Wireless G Broadband Router user manual Model 503693 INT-503693-UM-0608-01
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™ Wireless G Broadband Router, Model 503693. The Wireless G Broadband Router allows you to conveniently share your network connection with multiple users on your network — with or without wires. It delivers 10/100 Mbps (auto-sensing) WAN and LAN connections, and is interoperable with 54 Mbps (802.11g) and 11 Mbps (802.11b) devices over a 2.4 GHz band wireless network. The WAN connection wizard makes installation a snap.
safety & compliance statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents 1 hardware..................................................................................5 1.1 Front Panel / LEDs........................................ . .........................5 1.2 Rear Panel / Ports & Jacks.......................................................5 1.3 System Requirements................................... . .........................5 1.4 Connection the Router................................... . .........................6 2 configuration.....................................
1 hardware 1.1 Front Panel / LEDs The front panel of the Wireless G Broadband Router features several LEDs for immediate indication of the device’s operational status. LED PWR Status On Off CPU On Flashing Off WL Flashing Off WAN On Flashing Off 1/2/3/4 On Flashing Off Description Power is on. Power is off. The router is initializing. The router is operating properly. The router is experiencing a hardware error. The wireless radio function is enabled. The wireless radio function is disabled.
• Broadband Internet access service (DSL/cable/Ethernet) • DSL/cable modem that has an RJ-45 connector (not needed if you connect the router to the Ethernet) • Each PC on the LAN needs a working Ethernet adapter and an Ethernet cable with RJ45 connectors • TCP/IP protocol must be installed on each PC • Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.
2.2 Wireless Settings 2.2.1 Basic Settings Band — The three options in the drop-down menu are “2.4 GHz (G)” for 54 Mbps (802.11g); “2.4G Hz (B)” for 11 Mbps (802.11b); and “2.4 GHz (G+B),” which allows both 802.11g and 802.11b wireless stations to connect to the router. Mode — The default is “AP”; options are “Client,” “WDS,” “AP+WDS.” Network Type — The default is “Infrastructure”; when Mode is set to “Client,” this should be set to “Ad Hoc.” SSID — Enter a value of up to 32 characters.
2.2.3 Wireless Security Setup Encryption — Select “None,” “WEP,” “WPA,” WPA2” or “WPA2 Mixed.” • WEP: Wired Equivalent Protocol. • WPA: WI-FI Protected Access (WPA) is an intermediate solution for security issues. It uses Temporal Key Integrity Protocol (TKIP) to replace WEP. WPA Authentication Mode — “Enterprise” uses an external authentication server (e.g., RADIUS) and EAP just as IEEE 802.1X does; “Personal” uses pre-shared keys without the need for additional servers.
are on the access control list will be able to connect to your access point. When”Deny Listed” is selected, these wireless clients on the list will not be able to connect to the access point. 2.2.5 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, as the Ethernet does. To do this, you must set these APs in the same channel and set the MAC address of other APs you want to communicate with in the table and then enable the Wireless Distribution System. 2.2.
2.3 TCP/IP Settings 2.3.1 LAN Interface Setup IP Address — Enter the IP address of your router in dotted-decimal notation (factory default = 192.168.1.254). Subnet Mask — This determines the size of the network, and would normally be set to 255.255.255.0. DHCP — Drop-down options are “None,” “Client” and “Serve.” The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs connected to the router on the LAN.
Connection Type — Select “Continuous,” “Connect on Demand” or “Manual.” Idle Time — When the connection type is set to “Connect on Demand,” you can set the idle time. MTU Size — The normal MTU (maximum transmission unit) value for most Ethernet networks is 1492 Bytes. For some ISPs, you need to reduce the MTU. This is rarely required, however, and shouldn’t be done unless you’re sure it’s necessary for your ISP connection. DNS — Select “Attain DNS Automatically” or “Set DNS Manually.
2.4.3 MAC Filtering Similar to Port and IP Filtering (above), with similar options. Enable MAC Filtering — Select to modify the MAC filter. MAC Address — Enter the MAC address; for example, 00:e0:4e:3f:2d:c5. Protocol — Select “TCP,” “UDP” or “Both.” Current Filter Table — This displays the list of MAC filters. 2.4.4 Port Forwarding Entries on this screen allow you to automatically redirect common network services to a specific machine behind the NAT firewall.
2.4.6 DMZ The DMZ host feature allows one local host to be exposed to the Internet for a specialpurpose service, such as Internet gaming or videoconferencing. DMZ Host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function. DMZ Enable — Select to enable the function. DMZ Host IP Address — Enter an IP address; e.g., 192.168.
2.5.2 Statistics This screen displays the packet counters for transmission and reception as regards to wireless and Ethernet networks. 2.5.3 Dynamic DNS Settings Dynamic DNS is a service that provides you with a valid, unchanging Internet domain name (URL) to go with your (possibly ever-changing) IP address. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own Web site, FTP server or other server behind the router.
Enable NTP client update — Select to get the time from NTP (Network Time Protocol). NTP server — Select a server from the drop-down menu. Click “Apply Change” to get the time from the Internet (if connected). 2.5.5 Denial of Service A denial-of-service (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service. Enable DOS Prevention — Select to modify the function. Enable Source IP Blocking — Enter a source IP blocking time. 2.5.
2.5.7 Upgrade Firmware This screen lets you upgrade the AP firmware. NOTE: Do not power off the device during the upload, as doing so may crash the system. Browse... 2.5.8 Save/Reload Settings This screen lets you save current settings to a file or reload the settings from the file which was saved previously. You can also reset the current configuration to factory default settings. 2.5.9 Password Setup On this screen, you can set up the account to access the Web server of the access point.
3 specifications • NAT: Port forwarding • Firewall: - Port filter - IP filter - Access control based on ..
INTELLINET NETWORK SOLUTIONS™ offers a complete line of active and passive networking products. Ask your local computer dealer for more information or visit www.intellinet-network.com. Copyright © INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners.
