Installation Guide

Cellular PVC TRIM
Installation Guidelines
er substrates. Consult adhesive labeling to determine
suitability.
Glue joints should be secured with fasteners on each
side of the joint.
For best results, surfaces to be glued should be smooth,
clean and in complete contact with each other.
TOUCH UP
Recommend non-solvent base llers.
Very good with All Purpose Painter’s Putty and High
Performance Wood Filler.
Good with Fill-N-Finish Light Wood Filler and Shrink
Free Spackling.
Clean with a damp cloth with soap and water.
DRILLING AND ROUTING
Use standard wood working drills and routers.
Care should be taken to avoid frictional heat build-up.
Periodic removal of shaving from the drill hole may be
necessary.
Carbide tipped router bits are recommended.
MOISTURE
Veranda HP TRIM does not absorb moisture, it can be
installed at or below grade.
It is perfect for use in moisture prone applications
such as ground contact, masonry contact, hot tub
surrounds, freeze boards, rooines and garage door
jambs, etc.
EXPANSION & CONTRACTION
Allow 1/8” space per 18 foot for expansion and con-
traction, Veranda HP TRIM expands and contracts with
changes in temperature. Joints between pieces should
be glued to eliminate joint separation — see “gluing”
section.
Properly fastening Veranda HP TRIM along its entire
length will minimize expansion and contraction.
When gaps are glued on a long run of the board, al-
low suitable expansion and contraction space at ends
of the run.
Scarf joints are recommended to minimize seams and
allow expansion & contraction.
SPANNING
Never span Veranda HP TRIM more than 24”.
Must not be used in load bearing applications, but
maybe used in spanned applications such as sots
and ceilings, with suitable thickness.
Proper fastening will help reduce the possibility of ex-
cessive movement from expansion and contraction.
STORAGE AND HANDLING
Store on a at and level surface.
Should be handled in a fashion as pine, because it has
a density comparable to pine with more exibility.
Keep product free of dirt and debris at job site. If prod-
uct gets dirty, clean after installation.
Always store Veranda HP TRIM with manufacturer cover.
CUTTING
Use standard wood working equipment for cutting.
Carbide tipped blades are recommended.
Avoid using ne tooth metal cutting blades.
Rough edge from cutting may be caused by excessive
friction, poor board support, or improper tooling.
FASTENING
Use standard nail guns or wood working tools.
Stainless steel or hot-dipped galvanized nails are rec-
ommended.
Do not use brads, staples, wire nails, ring-shank nails or
ne-threaded wood screws.
Place nails and screws on center of board and keep ap-
proximately ¾” from each edge.
Fasteners should penetrate into at, solid wood sub-
strate or framing member a minimum of 1-1/4”.
Always use 2 fasteners per every framing member for
trim board applications. If 12” or wider, Veranda HP™
TRIM will require additional fasteners.
Veranda HP TRIM should be fastened into a at, solid
substrate. It can damage the board if fastened Veranda
HP TRIM into hollow or uneven areas. Shutter applica-
tion is not recommended.
If nailing product at 32°F or below, pre-drilling is re-
quired.
Pre-drilling and/or counter-sink are typically not re-
quired unless a larger fastener is used.
PAINTING
Clean surface prior to painting. The surface must be
clean, dry, and void of any foreign article and material
such as dirt, oil, grease or other contaminates.
Veranda HP TRIM does not require painting for protec-
tion like wood. Veranda HP TRIM accepts paints and
stains well.
Both oil base and latex paints are desirable. Follow
paint manufacturer’s recommendations.
Avoid painting dark colors in area of direct sunlight.
Acrylic or urethane based latex exterior or interior
paints are recommended. General brands such as
Sherwin Williams, Behr, Glide, etc. are all suitable.
Always use paint with Light Reective Value (LRV) of
55 or higher.
If paint darker color (LRV of 54 or lower), Vinyl safe
paint or paints specically designed for such applica-
tion must be used.
GLUING
Standard PVC cements or cellular cements provide a
strong Veranda HP TRIM to Veranda HP TRIM bond.
For the best result, glue all joints between trim pieces
such as long fascia runs, window surrounds, etc., to
prevent joint separation.
Various adhesives, such as epoxy or polyurethane ad-
hesives may be used to bond Veranda HP TRIM to oth-
©2012.3 VerandaHP TRIM installation
H IGH P ERFORMANCE
Oce: 9 Peach Tree Hill Road, Livingston, NJ 07039
TEL: [phone] / FAX: [phone]
www.VerandaHP.com / Please visit our website for
most updated Installation Guideline & Warranty