2 CHANNEL / 4 CHANNEL / 5 CHANNEL AUTOMOTIVE AMPLIFIER G2-600 / G2-800 / G2-1200 G4-600 / G4-800 / G4-1000 G5-900 INSTRUCTION MANUAL
Congratulations on your Purchase Your new high fidelity bridgeable/stereo amplifier is designed to deliver maximum enjoy ment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. Features • • • • • • • • • • • • Four Class ''AB'' High-Current Dual Discrete Drive Stages. Class ''AB'' Technology MOSFET PWM Power Supply. Bridgeable & TRI-Mode Operation.
• NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at the amplifier may cause damage to the amplifier and will void your warranty.
INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface.
CONNECTIONS INPUT CONNECTIONS This amplifier will accept low level inputs only. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use a "high to low converter" available through your local car audio shop. Connect the low level/line level RCA cables from the head unit, or signal processor, to the line level input on the amplifier. See Fig.
2CHANNEL SYSTEM WIRING DIAGRAM LINE INPUT GAIN BASS L.P.F H.P.F CH1 6V 0.2V 0dB 12dB 50Hz 250Hz L.P.F H.P.F FLAT 80Hz 1.2KHz CROSSOVER CH2 REMOTE CH1 CH2 AUTO - ANTENNA LEAD +12V REM GND CAR STEREO HEAD UNIT FIG.
4CHANNEL SYSTEM WIRING DIAGRAM LINE INPUT GAIN BASS FREQUENCY FREQUENCY BASS GAIN LINE INPUT CH1 CH3 6V 0.2V 0dB 12dB L.P.F H.P.F H.P.F L.P.F 0dB 12dB 50Hz 500Hz 50Hz 500Hz FLAT FLAT CH 1/2 CH2 6V 0.2V CH 3/4 CH4 CH1 CH2 CH3 CH4 AUTO - ANTENNA LEAD +12V REM GND CAR STEREO HEAD UNIT FIG.
5CHANNEL SYSTEM WIRING DIAGRAM CH 1/2 LINE INPUT CH1 CH3 GAIN 6V L.P.F CROSSOVER 0.2V 50Hz 250Hz L.P.F FLAT H.P.F H.P.F CROSSOVER 80Hz 1.2kHz 80Hz 1.2kHz FLAT H.P.F LINE INPUT L.P.F CH5 50Hz 250Hz GAIN CH2 CH4 6V CH6 0.2V 50Hz 250Hz FLAT CH 3/4 80Hz 1.2kHz CH 5 CH1 CH2 6V 0.2V CH3 CH4 CH5 CH6 AUTO - ANTENNA LEAD +12V REM GND CAR STEREO HEAD UNIT FIG.
SPEAKER CONNECTIONS This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel power is referred to stereo and mono at the same time. Minimum impedance remains the same for three channel (front /subwoofer) systems as long as proper passive crossovers are used. Connect right and left speaker wire to corresponding speaker output terminals of the amplifier.
SPEAKER CONNECTIONS 4 CH SPEAKER WIRING DIAGRAM 2 SPEAKER BRIDGED G4-1000 4 CHANNEL AMPLIFIER POWER GND REM B+ FUSE 40A 40A SPEAKER CH1 BRIDGED CH1 CH2 CH3 CH3 CH4 4-8 Ohms CH4 2 CH 2 SPEAKER + 1 SUBWOOFER 1 CH G4-1000 4 CHANNEL AMPLIFIER POWER GND CH2 REM B+ FUSE 40A 40A SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH3 CH3 CH4 CH4 3 CH 2-4 Ohms 1CH 2-4 Ohms 2 CH SUB WOOFER 4-8 Ohms 4 SPEAKER STEREO G4-1000 4 CHANNEL AMPLIFIER POWER GND REM B+ FUSE 40A 40A 1 CH SPEAKER CH
SPEAKER CONNECTIONS 5 CH SPEAKER WIRING DIAGRAM 3 SPEAKER BRIDGED 5 CHANNEL AMPLIFIER POWER GND REM B+ G5-900 FUSE 40A 40A SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH5 CH3 CH3 CH4 CH5 CH4 2-8 Ohms 3 CH 2 CH 1 CH 4-8 Ohms 5 SPEAKER STEREO 2-4 Ohms 1 CH 5 CHANNEL AMPLIFIER POWER GND REM B+ G5-900 FUSE 40A 40A 2 CH SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH5 CH3 CH3 CH4 CH5 3 CH CH4 2-8 Ohms 5 CH 4 CH 2-4 Ohms SUBWOOFER 7 SPEAKER HEX MODE 4-8 Ohms 5 CH 4-8 Ohms 1 CH 5 CHANNEL A
ADJUSTMENTS 1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave.
FRONT/REAR PANEL 2CHANNEL LINE INPUT GAIN L.P.F BASS H.P.F CH1 6V 0.2V 50Hz 250Hz L.P.F H.P.F FLAT 0dB 12dB 80Hz 1.
FRONT/REAR PANEL 4CHANNEL 4 CHANNEL AMPLIFIER POWER GND REM B+ G4-600 FUSE 40A SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH3 CH3 CH4 CH4 G4-600 REAR 4 CHANNEL AMPLIFIER POWER GND REM B+ G4-800 FUSE 30A 30A SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH3 CH3 CH4 CH4 G4-800 REAR 4 CHANNEL AMPLIFIER POWER GND REM B+ G4-1000 FUSE 40A 40A SPEAKER CH1 BRIDGED CH1 CH2 CH2 CH3 CH3 CH4 CH4 G4-1000 REAR 5CHANNEL CH 1/2 LINE INPUT CH1 CH3 GAIN 6V L.P.F CROSSOVER H.P.F H.P.
TROUBLE SHOOTING GUIDE. This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.
SPECIFICATION AMPLIFIER G2-600 G2-800 G2-1200 4 OHMS @ 0.05% THD 100W x 2 150W x 2 225W x 2 4 OHMS Bridged 0.5% THD 200W x 1 300W x 1 450W x 1 MAXIMUM OUTPUT POWER 600 Watts 800 Watts 1200 Watts YES (OPTIONAL) YES (OPTIONAL) YES (OPTIONAL) LOW PASS FILTER 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) 50Hz-250Hz (VARIABLE) HIGH PASS FILTER 80Hz-1.2kHz (VARIABLE) 80Hz-1.2kHz (VARIABLE) 80Hz-1.
SPECIFICATION G4-600 G4-800 G4-1000 G5-900 60W x 4 90W x 4 110W x 4 60W x 4 + 160W x 1 4 OHMS Bridged 0.5% THD 105W x 2 175W x 2 225W x 2 120W x 2 + 160W x 1 MAXIMUM OUTPUT POWER 600 Watts 800 Watts 1000 Watts 900 Watts N/A N/A N/A N/A LOW PASS FILTER 50Hz-500Hz (VARIABLE) 50Hz-500Hz (VARIABLE) 50Hz-500Hz (VARIABLE) 50Hz-250Hz (VARIABLE) HIGH PASS FILTER 50Hz-500Hz (VARIABLE) 50Hz-500Hz (VARIABLE) 50Hz-500Hz (VARIABLE) 80Hz-1.
WARRANTY WARRANTY LIMITATIONS The following is NOT covered under Interfire Audio's warranty program: 1. Product owned by anyone other than the original purchaser from an authorized Interfire Audio dealer. (The warranty is NOT transferable and will not apply to products purchased from unauthorized dealers.) 2. Speaker products that have been overpowered, causing thermal (burnt voice coil) and/or mechanical failure (ripped surrounds or spiders). 3.
Interfire Audio, Inc. Santa Fe Springs, CA 90670 www.interfireaudio.