Inc. Speaker User Manual
COMPONENT WOOFER INSTALLATION INSTRUCTION MANUAL
MOUNTING LOCATION
Carefully select a suitable mounting location for the speaker/tweeter. Be sure to check
behind the mounting location selected for adequate space for speaker/tweeter depth.
Use the included template if needed
MOUNTING HOLE
SPEAKER : Using a sharp knife or razor, cut the panel using the outline from the template as a guide. Also,
drill holes for the mounting screws if installing on metal panels.
INSTALLATION
SPEAKER : Place ABS grill on top of speaker and secure assembly using the self tapping
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.
TWEETER : Screw the angle mounting to the location selected or use the double sided
tape provided to stick the flush mounting to the location selected.
WIRING
INSTALLATION PROCEDURE :
Speaker
Tweeter
Interfire Audio Inc.
Santa Fe Springs, CA ,
www.inter f i reaudio. c o m
SPEAKER: Carefully route the supplied wire to the speaker, ensuring that it does not pass over any sharp
metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers,
watching that the left/right and positive/negative connections are made correctly to the appropriate
outputs of the radio or amplifier.
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening
and connect these wires to the line wires coming from the included outboard crossover tweeter
terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.
Moun t i ng Hol e s
Spe a k er Un i t
Moun t i ng Scr e ws
Gri l l
Twe ete r
Sc r ew
An g le M o unt i n g
Do ub le si de d
Ta pe
Fl u sh M o unt i ng
Pea k P owe r H and lin g
Con tin uou s P owe r ( RMS )
Imp eda nce
Mag net Wei g ht
Sen sit ivi ty (1W /m)
Fre q. Res pon se
Woof e r Voic e C o il Di a .
Fo (Fr eq. Re sp. )
Qts (Tot al Q)
Va s
Cro sso ver
: 3 00Watt s
: 1 50 Wa t ts
: 4 Oh m
: 1 0 O z
: 9 1 d B
: 5 0Hz - 25k Hz
: 1 " ( 25m m) ASV
: 9 2.0 6 H z
: 0 .82
: 4 .1 Lt
: 1 2dB /Oc t
MODEL : IFC-525
5.2 5" 2-Way Hig h D efi nit ion
Com pon ent Sy ste m
5.2 5" Inj ect ion PP M ic a C o ne
Rub ber Su rro und an d
1" Ti t an i um Do m e Tw ee t er
wit h N eod ymi um Mag net
Pea k P owe r H and lin g
Con tin uou s P owe r ( RMS )
Imp eda nce
Mag net Wei g ht
Sen sit ivi ty (1W /m)
Fre q. Res pon se
Woof e r Voic e C o il Di a .
Fo (Fr eq. Re sp. )
Qts (Tot al Q)
Va s
Cro sso ver
: 3 50Watt s
: 1 75 Wa t ts
: 4 Oh m
: 1 3 O z
: 9 1 d B
: 4 0Hz - 25k Hz
: 1 " ( 25m m) ASV
: 5 3.1 Hz
: 0 .61
: 1 2.4 2 L t
: 1 2dB /Oc t
MODEL : IFC-650
6.5 " 2 -Wa y H ig h D e fi n it i on
Com pon ent Sy ste m
6.5 " I nje cti on PP M i ca Co n e
Rub ber Su rro und an d
1" Ti t an i um Do m e Tw ee t er
wit h N eod ymi um Mag net
SPECIFICATIONS :
COMPONENT WIRING DIAGRAM:
INPUT
WOOFER
SIGNAL SOURCE UNIT
RADIO OR AMPLIFIER
TWEETER
EXTERNAL 2-WAY
CROSSOVER
*NOTE : When installing tweeter with flush mount kit, a hot glue gun is sometimes necessary to secure
the tweeter's flush mount housing.