MONO CHANNEL CLASS "D" AUTOMOTIVE AMPLIFIER D900.1 / D1700.1 / D3000.
CONGRATULATIONS ON YOUR PURCHASE Your new high fidelity mono block amplifier is designed to deliver maximum enjoyment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation.
INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface.
SPEAKER WIRING The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to only one output terminal. See diagram below.
MONO BRIDGED MASTER SLAVE Master Amplifier MASTER SLAVE L 6V R 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.F BASS BOOST REMOCON SLAVE LINE INPUT FROM RADIO MASTER Slave Amplifier MASTER SLAVE SLAVE L 6V R 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.
MONO BRIDGED Master Amplifier SPEAKER FUSE POWER +12V REM GND ON PROTECT Using a lead wire of 8 gauge or bigger connect from the master Amp's negative(-) speaker terminal to the slave Amp's negative(-) speaker terminal.
MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION Master Amplifier SPEAKER FUSE POWER +12V REM GND ON PROTECT Voice Coil1 Voice Coil2 SPEAKER FUSE POWER +12V REM GND Slave Amplifier Master Amplifier ON PROTECT SPEAKER FUSE POWER +12V REM GND ON PROTECT SPEAKER FUSE POWER +12V Slave Amplifier REM GND ON PROTECT 6
POWER SUPPLY CONNECTIONS The Class "D" amplifier is designed to work within 10 to 16 volts DC. Before any wires are connected, the vehicle's electrical system should be checked for correct voltage supply with the help of a voltmeter. First check the voltage at the battery terminals with the ignition in the off position. The voltmeter should read no less than 12 volts. Next, check the battery with the engine running between 1500 and 2000 rpm. The voltmeter should now read between 13.5 and 14.5 volts.
OPERATION 1 2 3 4 5 6 MASTER 7 SLAVE L 6V R 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.F REMOCON BASS BOOST SLAVE LINE INPUT 1. RCA Input Jacks 2. Input Level Control 4. Bass Boost 5. Remote Control Jack 6. Master/Slave Switch 3. Low Pass Frequency 7. Slave Input Jack Control and Crossover 1. RCA Input Jacks - Low level-high impedance inputs. Use high quality RCA cables designed for mobile applications. 2. Input Level Control - Adjust the input level for the marked channels.
FRONT/REAR PANEL MASTER SLAVE L 6V 0.2V 50Hz 250Hz 0dB 12dB GAIN R L.P.F REMOCON BASS BOOST SLAVE LINE INPUT D900.1, D1700.1, D3000.1 SPEAKER FUSE 25A 25A POWER 25A +12V REM GND ON PROTECT D900.1 D900.1 SPEAKER FUSE 30A 30A POWER 30A +12V REM GND ON PROTECT D1700.1 D1700.1 SPEAKER POWER +12V REM GND ON PROTECT D3000.1 D3000.
TROUBLE SHOOTING GUIDE. This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.
SPECIFICATION AMPLIFIER D900.1 D1700.1 D3000.1 RMS POWER / 1 ohm @ 1% T.H.D 900W x 1 1700W x 1 3000W x 1 2 ohms @ 0.05% T.H.D 650W x 1 1000W x 1 2000W x 1 4 ohms @ 0.05% T.H.
Interfire Audio, Inc. Santa Fe Springs, CA 90670 www.interfireaudio.