Assembly Instructions

ManualsBrandsInterion ManualsCubicle Partition PanelsOffice Partition Panel with Pass-Thru Cable, 36-1/4"W x 46"H, Blue

Assembly Instructions1-800-645-2986

OFFICE PARTITIONS

STEP 1

Remove opening blanks on

raceway cover for power and data.

If panel contains no electric or data

and is used as a pass-thru, leave

opening blanks in place.

Rear view

Data Port

Openings

Power Box Opening

Rear View

Front View

STEP 2

Insert data ports and data cables before

installing raceway cover. (Phone connectors,

data connectors and cables not included.)

Removable, hinged raceway cover allows

easy access to receptacles and cables

Notch

Rear

Panel

Notch

Lip

Notch

STEP 1

Place notches in raceway

cover over the lips

located on raceway leg.

STEP 2

Swing panel upward until

magnet snaps into place.

Adjust accordingly.

TIP

Push or pull magnetic tabs in or out

for a better fit. Adjust as needed.

Use cable tie bracket

to dress data cables

under panels.

Use twist ties

or zip ties to

fasten cables

under panels

as needed.

Office Partitions With Electric 4/16/10 3:17 PM Page 1

Summary of content (13 pages)

PAGE 1
Office Partitions With Electric 4/16/10 1-800-645-2986 3:17 PM Page 1 Assembly Instructions OFFICE PARTITIONS Power Box Opening Rear View N Data Port Openings Front View STEP 1 STEP 2 Remove opening blanks on raceway cover for power and data. If panel contains no electric or data and is used as a pass-thru, leave opening blanks in place. Insert data ports and data cables before installing raceway cover. (Phone connectors, data connectors and cables not included.
PAGE 2
Office Partitions With Electric 4/16/10 3:17 PM Page 2 Assembly Instructions Customer Service 1-800-645-2986 globalindustrial.com Office Partitions With Electric WARNING ASSEMBLY In order to prevent structural failure, instability, tipover, and/or serious injury, please follow instructions carefully. • Configurations require the corresponding steps needed for proper assembly. • Attach appropriate brackets or legs on the ends of the panels as needed.
PAGE 3
Office Partitions With Electric 1-800-645-2986 Go To “A” 4/16/10 3:17 PM Page 3 OFFICE PARTITIONS Go To “B” Go To “D” Assembly Instructions Go To “C” Go To “E” Go To “F” Go To “I” Go To “G” Go To “H” 2
PAGE 4
Office Partitions With Electric 4/16/10 1-800-645-2986 I 3:17 PM Page 4 Assembly Instructions OFFICE PARTITIONS STEP 1 STEP 4 Remove feet from panel. Attach connectors to top and bottom. Insert panel studs. P2 P1 H14 STEP 2 H13 Attach raceway to bottom of panels. Add feet and bottom bracket. STEP 3 H9 Attach aluminum plate(s) to bottom of raceway.
PAGE 5
Office Partitions With Electric 4/16/10 1-800-645-2986 3:17 PM Page 5 Assembly Instructions OFFICE PARTITIONS H16 H - Right H15 P1 STEP 1 STEP 6 Insert panel filler caps into panel filler post top and bottom. Insert post into bottom bracket first, then into top bracket. Then tighten all bolts firmly Remove feet from panel. Attach connectors to top and bottom. STEP 2 Attach raceway to bottom of panels. Add feet and bottom bracket. H11 H7 STEP 5 STEP 4 P2 Insert panel studs.
PAGE 6
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 Page 6 Assembly Instructions OFFICE PARTITIONS A H13 STEP 1 Remove feet from panel. Attach connectors to top and bottom. H1 P1 STEP 2 Attach raceway to bottom of panel. Add feet and bottom bracket. P1 STEP 3 H13 Attach aluminum plate(s) to bottom of raceway. Foam seal may need to be trimmed to fit panel. H1 H13 (2) (6) H18 H19 (1/2)* (2/4)* Note: Hardware to anchor wall bracket to wall is not provided.
PAGE 7
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 C Page 7 Assembly Instructions OFFICE PARTITIONS STEP 1 Remove feet from panel. Attach connectors to top and bottom. STEP 5 STEP 4 Insert panel studs Loosely attach top bolts H13 P2 H3 P1 H14 Foam seal may need to be trimmed to fit panel H13 STEP 3 Attach aluminum plate(s) to bottom of raceway. STEP 2 Attach raceway to bottom of panels. Add feet and bottom bracket.
PAGE 8
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 G Page 8 Assembly Instructions OFFICE PARTITIONS STEP 1 STEP 4 STEP 5 Remove feet from panel. Attach connectors to top and bottom. Loosely attach top bolts. Insert panel studs. P2 P3 P1 H14 H13 STEP 2 STEP 6 Attach raceway to bottom of panels. Add feet and bottom bracket. Insert panel filler caps into filler post top and bottom. Insert post into bottom bracket.
PAGE 9
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 E Page 9 Assembly Instructions OFFICE PARTITIONS STEP 1 STEP 4 Remove feet from panel. Attach connectors to top and bottom. Loosely attach top bolts H13 H5 P1 Foam seal may need to be trimmed to fit panel STEP 5 Insert panel studs H13 STEP 2 Attach raceway to bottom of panels. Add feet and bottom bracket. P2 P3 P4 STEP 3 Attach aluminum plate(s) to bottom of raceway.
PAGE 10
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 F Page 10 OFFICE PARTITIONS Assembly Instructions STEP 1 Remove feet from panel. Attach connectors to top and bottom. STEP 4 Insert panel studs. Foam seal may need to be trimmed to fit panel P1 P2 H13 H14 STEP 2 Attach raceway to bottom of panel. Add feet and bottom bracket. STEP 3 H3 Attach aluminum plate to bottom of raceway. H18 H19 STEP 5 STEP 6 Bolt and tighten top bracket H8 onto panel 2.
PAGE 11
Office Partitions With Electric 4/16/10 1-800-645-2986 J 3:17 PM Page 11 OFFICE PARTITIONS Assembly Instructions INSTALLATION OF POWER BOX WARNING Fire Risk. Connection to the power source, by a licensed electrician, and quantity of receptacles used for a given circuit, must be in compliance with all national and local electrical codes. Failure to observe this warning could result in a fire. Risk of electrical shock. Be sure in-feed power is disconnected to prevent personal injury.
PAGE 12
Office Partitions With Electric 4/16/10 3:17 PM 1-800-645-2986 Page 12 OFFICE PARTITIONS L Assembly Instructions Receptacle Removal Tool is required when removing receptacles from power box. Each power box accepts up to 6 simplex receptacles; 3 per side. SIMPLEX RECEPTACLE TYPES 1 2 IG 4 Circuit 1 Circuit 2 Circuit 3 Circuit 4 Isolated Use blank to fill “empty” simplex locations on power box. WARNING Maximum 16 simplex receptacles per 15 amp circuit.
PAGE 13
Office Partitions With Electric 4/16/10 1-800-645-2986 Q 3:17 PM Page 13 OFFICE PARTITIONS Assembly Instructions STEP 1 Depending on where your power source comes from, remove opening blank from End Cap, Three Way or Corner Cap. Place over starter cable and attach to bottom of panel raceway. Adjust accordingly. STEP 2 If power source does not exit from End, Corner or Three Way, leave opening blank in place and attached cap as needed. Finished Three Way with power source exiting raceway.