Assembly Instructions

ManualsBrandsInterion ManualsCubicle Partition PanelsOffice Partition Panel, 48-1/4"W x 96"H, Tan

Office Partitions

Assembly

Instructions

Customer Service

1-800-645-2986

Low-Hi (90˚)

3 - W ay Connector

Straight Extension

Hi-Low (90˚)

Right/Left Connector

90˚ Connector

S c r e w

Adjust all levelers to

approximately 1-1/4”

HARDWARE

A S S E M B LY

• Configurations require the corresponding

steps needed for proper assembly.

• Attach appropriate brackets or legs on

the ends of the panels as needed.

• Panels must be level. Level each panel.

• Do not attach bolts or brackets into the

outermost edge of a panel that will be last

in line.

• Starter panel should use a corner, 3-way,

4 - w a y, or wall bracket.

• Insert bolt cap into unused threaded

insert to finish your project.

• Level each panel as you go along.

H8 H9 H10 H11

Panel Filler Cap Panel Filler PostHex Bolt Threaded Stud Bolt Cap

H13 H14 H15 H16 H17

Toggle Bolt

H12

Straight Connector 3-way ConnectorWall Bracket

Right A n g l e

(90˚) Connector

4-way Connector

H1 H2 H3 H4 H5

T- L e g

WARNING

In order to prevent structural failure, instability,

t i p - o v e r, and/or serious injury, please follow

i n s t r uctions care f u l l y. Do not use hanging shelf or

o v e r head cabinet with panels that have glass.

• Use only the instructions, parts and

hardware included

• Maximum span for connected

panels without support is 12 feet

• Do not move panels while they are connected together

• Maximum span for connected

panels using overhead cabinets or

shelves without support is 12 feet

• Requires 2 people for assembly

• Not for outdoor or high humidity areas

12’

O v e r h e a d

C a b i n e t s

O v e r h e a d

S h e l v e s

Summary of content (10 pages)

PAGE 1
Assembly Instructions Customer Service 1-800-645-2986 Office Partitions WARNING ASSEMBLY • Configurations require the corresponding steps needed for proper assembly. • Attach appropriate brackets or legs on the ends of the panels as needed. • Panels must be level. Level each panel. • Do not attach bolts or brackets into the outermost edge of a panel that will be last in line. • Starter panel should use a corner, 3-way, 4-way, or wall bracket.
PAGE 2
1-800-645-2986 Office Partitions Go To “A” Go To “B” Go To “D” Go To “C” Go To “E” Go To “G” Assembly Instructions Go To “F” Go To “H” Go To “I” Go To “J” 2
PAGE 3
1-800-645-2986 Office Partitions Assembly Instructions A H13 H1 P1 Start at wall and level panel H1 P1 Foam seal may need to be trimmed to fit panel H13 H1 H13 (2) (4) Note: Hardware to anchor wall bracket to wall is not provided.
PAGE 4
1-800-645-2986 Assembly Instructions Office Partitions C STEP 2 Loosely attach top bolts H13 STEP 1 P2 H3 P1 H14 Foam seal may need to be trimmed to fit panel H13 P2 H3 H3 (2) P1 H13 (6) H14 STEP 3 Fit panel studs into bottom bracket, then bolt and tighten top bracket (2) D Loosely attach top bolts H13 STEP 2 STEP 1 P2 P3 H4 P1 P1 H14 H16 STEP 3 H13 Fit panel studs into bottom bracket, then loosely attach to top bracket H4 H15 P3 P1 P2 STEP 4 H4 H13 (2) (8) H14 (4) H
PAGE 5
1-800-645-2986 Assembly Instructions Office Partitions E STEP 2 H13 Loosely attach top bolts P2 P3 P4 H5 P1 H14 P1 P3 STEP 3 Fit panel studs into bottom bracket, then loosely attach to top bracket H5 P1 P2 P3 H13 STEP 4 H5 (2) H13 (10) P2 Fit panel studs into bottom bracket first, then into top bracket. Then tighten all bolts.
PAGE 6
1-800-645-2986 Assembly Instructions Office Partitions G STEP 1 P1 STEP 2 Foam seal may need to be trimmed to fit panel. P2 H13 H3 H14 STEP 3 STEP 4 Bolt and tighten top bracket H8 onto panel 2. Align panel to bracket and screw in using 2 self tapping screws and washers (H11) until tight (do not overtighten). H13 H8 H11 P1 P2 P1 Fit panel studs into panel bracket.
PAGE 7
1-800-645-2986 Assembly Instructions Office Partitions H STEP 2 Loosely attach top bolts. H13 STEP 1 P2 P3 H10 P1 H14 H16 H15 STEP 3 Insert panel filler caps into filler post top and bottom. Insert post into bottom bracket. Fit panel studs into bottom bracket, then bolt and tighten top bracket. H13 H4 P2 P1 H13 STEP 4 Assembled panels P1 and P2. H16 STEP 6 H8 P2 P2 Bolt on top bracket H8 to short panel 3. P1 P3 Drill holes where marked from previous Step 5.
PAGE 8
1-800-645-2986 I - Right Assembly Instructions Office Partitions H7 STEP 2 STEP 1 Loosely attach top bolts. P1 H16 P2 H2 H13 H15 P1 STEP 3 Insert panel filler caps into panel filler post top and bottom. Insert post into bottom bracket first, then into top bracket. Then tighten all bolts firmly P2 I - Left H14 P1 H11 P2 H7 STEP 2 STEP 1 STEP 4 Align panel to bracket and screw in using 2 self tapping screws and washers (H11) until tight (do not overtighten). Loosely attach top bolts.
PAGE 9
1-800-645-2986 Assembly Instructions Office Partitions J STEP 2 P2 P3 STEP 1 P1 H14 H13 STEP 3 Loosely attach top bolts H13 H9 STEP 4 H4 P3 Insert panel filler caps into panel filler post top and bottom H16 H15 P1 H9 STEP 5 Insert post into bottom bracket first. Fit panel studs into bottom bracket then attach bracket to panel 2. Tighten bolts H9 H13 P3 P2 P1 STEP 6 H11 Align panel 1 to bracket and screw in self tapping screws and washers H11 into side of panel 1.
PAGE 10
1-800-645-2986 Office Partitions Layout 012014 10 Assembly Instructions