Installation Manual

ManualsBrandsInterlogix ManualsElectronicsConcord 5 Inch TouchScreen

Concord 5” TouchScreen Installation Sheet

Description

Concord 5” TouchScreen, model 60-924-3-C4TS5, features a

5-inch color LCD screen with a graphical user interface

designed to control basic functionality of Concord 4, version

4.5 or later.

Multiple touch screens can be added to each Concord panel.

An internal speaker provides system status beeps for trouble

and alarm indications.

The touch screen provides a convenient option for the

following system operations:

• Easily obtain home/building status using At-A-Glance

(AAG) sensor status.

• Arm the system (doors, windows, motion sensors, and

property).

• Disarm the system.

• Activate a panic alarm to call the central monitoring station

in a non-medical emergency.

Equipment

• Alphanumeric keypad (for panel and end user

programming)

• 4-conductor, 18 to 22-gauge wire

• #6 screws and anchors (included)

• Super bus power supply (optional), PN 600-1019

Tools

• 2.5mm flat-blade screwdriver

• #2 Phillips screwdriver

• Drill and drill bits for opening wallboard (3/16- and 1/2-inch

bits)

Safety information

IMPORTANT SAFETY INFORMATION. READ ENCLOSED

WARNINGS AND SAFETY INFORMATION.

WARNING! Disconnect panel power before servicing.

CAUTION: Use static electricity precautions when

handling electronic components.

Installation guidelines

The touch screen can be the primary interface to the panel or it

can act as auxiliary interface working in conjunction with

alphanumeric keypads (such as Interlogix P/N 600-1070-E or

60-983).

• The touch screen is not listed to UL Fire Standards and

may not be programmed for use with a Fire System in

California per CSFM Regulations.

• Mount the touch screen in an environmentally-controlled

area (32°F to 120°F/0°C to 49°C).

• Do not exceed the maximum available power given in the

panel. Refer to the total system power and guideline

section in Concord installation instructions. See Table 1

for touch screen power usage and Table 2 for maximum

wire length between touch screen and panel.

• Depending on system loading, multiple touch screens can

be installed on a Concord 4 system. See the examples in

Table 3 and Table 4.

Table 1: Touch Screen Power Usage

Current (mA)

Conditions

400

Maximum alarm current with the buzzer sounding and

the touch screen illuminated from a button press

100

Typical operation

Power saving mode (no panel AC power)

Table 2: Maximum SuperBus Lengths

Wire gauge

(shielded or

unshielded)

Max. touch screen wire length between touch

screen and panel

120 feet

Summary of content (8 pages)

PAGE 1
Concord 5” TouchScreen Installation Sheet Safety information IMPORTANT SAFETY INFORMATION. READ ENCLOSED WARNINGS AND SAFETY INFORMATION. WARNING! Disconnect panel power before servicing. CAUTION: Use static electricity precautions when handling electronic components. Installation guidelines The touch screen can be the primary interface to the panel or it can act as auxiliary interface working in conjunction with alphanumeric keypads (such as Interlogix P/N 600-1070-E or 60-983).
PAGE 2
Table 3: Example – Basic Concord 4 system with two Concord 5” TouchScreens and one alphanumeric keypad Device Part # Number used Alarm current draw Concord 4 2. Available Power 1000 mA Concord 5” Touch Screen 60-924-3C4TS5 2 800 mA ATP 1000 60-983 1 110 mA Total Remove the touch screen from the mounting base pressing the opening button on the bottom of the touch screen (as shown in Figure 2).
PAGE 3
Figure 4: Bus Wire Routing Wall Mount Figure 6: Connecting the touch screen GND (Black) BUS-B (White) BUS-A (Green) +12V (Red) 4 3 2 1 Wires Terminal block 7. Hang the base using the screws, level the base, and tighten the screws. 8. Feed any extra bus wire back into wall. Bus wires should not protrude outside of the bus wire drop opening. Surface, desktop mounting If the unit is to be wall mounted, skip to step 11. 9.
PAGE 4
Press and hold the Enter button for approximately five seconds. The following screen will appear: 3. Exit programming mode. 4. Remove AC and battery power from the panel. 5. Replace the defective bus device with a new one. 6. Apply AC and battery power to the panel. Partition assignment With this menu, assign bus devices to work in the desired partition. To assign bus devices to partitions: The emulated keypad works and functions the same as the 600-1070-E keypad.
PAGE 5
TouchScreen setting options Touch the Settings icon Settings screen appears. on the Home screen and the Setting options With the Setting options, adjust the touch screen’s features. Typical status indicators (excluding light screen): • Gold - A button is selected. • Blue - Buttons not selected. Note: If this device (or any other keypad) is located in areas that are less secure such as a garage which is not monitored, be sure Quick Exit is programmed to off.
PAGE 6
Testing Problem Actions/Solutions Test the touch screen operation by arming/disarming the system, activating the touch screen panics, and bypassing sensors to verify correct operation. Trouble condition not displayed under status Refer to event buffer in touch screen and/or view full status on alphanumeric keypad.
PAGE 7
measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PAGE 8
/8 P/N 466-5410 (EN) • REV D • ISS 19MAR18