Installation Manual

P/N 466-5410 (EN) • REV D • ISS 19MAR18 5 / 8
TouchScreen setting options
Touch the Settings icon on the Home screen and the
Settings screen appears.
Setting options
With the Setting options, adjust the touch screen’s features.
Typical status indicators (excluding light screen):
• Gold - A button is selected.
• Blue - Buttons not selected.
Use the scroll bar to see all of the options (below):
Event History - Touch the Related Show button to view
system events.
Direct Bypass - Touch the Related button to bypass a sensor.
Panel Status - Touch the Related Show button to display the
status of the security system.
Change Partition - Touch the Related button to change
partitions.
Chime - Touch the On or Off button to toggle the touch screen
chime feature on or off. This feature will enable this touch
screen to beep when a certain door opens. Consult the dealer
regarding which doors or windows are programmed to chime
when opened. Refer to the security panel documentation for
information on this feature.
Keypress Volume - Touch the arrow buttons to adjust this
touch screen’s keypress volume level. The siren sounds are
not controlled by this setting.
Beep Volume - Touch the arrow buttons to adjust this touch
screen’s beep volume level. The siren sounds are not
controlled by this setting.
Brightness - Touch the arrow buttons to adjust the brightness
level of this touch screen’s screen.
Default screen - Use this feature to set this touch screen’s
screen saver mode. Select Blank to have the screen and LED
go dark after a period of inactivity. Otherwise, the default will
be the Home screen and the screen will always be lit.
The touch screen will automatically blank daily at 2:00 AM for
60 minutes.
Calibration – The touch screen typically does not need to be
calibrated. However, if the touch screen buttons do not
respond correctly, touch the Show button to access the
Calibration screen. To calibrate the touch screen, touch the +
icons in the corners of the screen using a soft, fine point.
Help - Touch the Help button to access the Help menu, which
displays a list of help topic buttons. Touch the buttons for
information on a given topic.
Set Date/Time - Touch the related button to access the
Date/Time menu.
Code Required Access - Touch the On or Off buttons to
toggle this feature. When turned on, it will require a user
access code to be entered for most touch screen functions.
With code required access, not all icons will be displayed.
Note: If this device (or any other keypad) is located in areas
that are less secure such as a garage which is not monitored,
be sure Quick Exit is programmed to off.
Emergency Keys (Default on) - Touch the On or Off buttons
to toggle this feature. There will be a prompt to enter a code.
Installer or dealer code must be used. When turned on, the
Emergency button appears. When turned off, the Emergency
button does not appear.
Fire Key (Default off) - Touch the On or Off buttons to toggle
this feature. There will be a prompt to enter a code. Installer or
dealer code must be used.
The fire emergency key will show that the fire key is active. If
the fire emergency option is on, the button
appears under the fire button. If the emergency option is off,
the button does not appear if the button is
pressed.
Note: The Emergency keys and Fire key programming options
appear only within two minutes of initial power up or if the
touch screen is reset.
Status LED
The touch screen has an LED that indicates power and sleep
mode status at a glance. Table 5 explains LED behavior.
Table 5: Status LED
LED
System status
Solid blue (while
backlights are on)
Primary power present
Fading blue
Primary power failure
Off
Screen saver active
Operation
Refer to Concord 5 in TouchScreen User Guide for basic touch
screen operation information.
Refer to the panel documentation for complete Concord 4
programming and operation information.
Emergency button
Touch the button and an Emergency screen
appears. Depending on the system, two or three buttons (the
Panic and Police buttons or the Panic, Police, and Fire
buttons) may appear. Select the appropriate button.
An emergency alarm initiated by mistake can be canceled by
touching the button and entering your user
access code within 30 seconds.
Note: The fire panic cannot be canceled.