Instruction Manual

ManualsBrandsInterlogix ManualsSensorsAP750-ID

AP750-ID Installation Instructions

Description

The AP750-ID is an addressable PIR device that interfaces

with the PinPoint® system. This system provides flexible and

reliable two-way communication between the device and the

controller.

Figure 1: Exploded view

1 - Corner mounting knockouts

2 - Base indent

3 - Wall mounting bracket

4 - Flat wall mounting knockout

5 - Cable entry

6 - Tamper actuator

7 - Flat wall mounting knockout

8 - Tabs

9 - Wiring access

10 - Circuit board

Parts included

• PIR detector

• Two plastic masks

• One screw to secure the to the wall mounting bracket

• Wall mounting bracket

• Sheet of adhesive masking labels

• Cardboard undercrawl window mask

Selecting a location

Mount the unit:

• On a rigid vibration-free surface.

• 6 to 10 feet (1.8 to 3m) high, but at least 6 inches (15cm)

from the ceiling.

• So the expected movement of an intruder is across the

fields of the detection pattern. See Figure 2 below.

Figure 2: Detection pattern

10.0 ft.(3.0m) maximum

8.0 ft.(2.4m) nominal

6.0 ft.(1.8m) minimum

8.0 ft.(2.4m)

25.0 ft.(7.6m)

50.0 ft.(15.2m)

10.0 ft.(3.0m)

33.0 ft.(10.1m)

Do not locate the unit:

• On a surface exposed to moisture.

• Where it may be exposed to false alarm sources such as:

direct sunlight, heat sources (heater, radiators, etc.) in the

field of view, strong air drafts (fans, air conditioner, etc.).

P/N 1036045 • REV C • 16MAY11 1

Summary of content (4 pages)

PAGE 1
AP750-ID Installation Instructions Description Selecting a location The AP750-ID is an addressable PIR device that interfaces with the PinPoint® system. This system provides flexible and reliable two-way communication between the device and the controller. Figure 1: Exploded view Mount the unit: • • • 2 On a rigid vibration-free surface. 6 to 10 feet (1.8 to 3m) high, but at least 6 inches (15cm) from the ceiling. So the expected movement of an intruder is across the fields of the detection pattern.
PAGE 2
• Where the ambient temperature is below 32° F (0°C) or above 131°F (55°C). If necessary, use one or more of the following methods to modify the coverage pattern: • Mounting the unit • 1. Separate the PIR unit from the mounting bracket by inserting a small, flat-bladed screwdriver between the tabs at the bottom of the unit and turning the screwdriver to push the tabs apart. See Figure 1 on page 1. Caution: You must be free of static electricity before handling sensor circuit boards.
PAGE 3
Figure 6: Detector back Note: The LED only lights if the unit is placed in Walktest Mode by the installer and the unit is enrolled in the system. Opening tab OUT IN -+-+ Walk testing Terminal block 1 2 3 4 5 6 7 8 ON APEMS Tamper switch DIP switches Switch settings: 33'(10.1m) STD 50'(15.2m) BI A Walktest Mode for testing the unit operation and coverage pattern is provided. Use the following instructions to walk test the unit: 1. Ensure the unit is enrolled in the PinPoint system. 2.
PAGE 4
As shown in Figure 7 below, pets are free to roam below the mounting height of the unit without causing alarms. Figure 7: Pet alley Regulatory information Listings UL 639 FCC compliance (Class A & B) This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. Certification 3 ft. (0.