AT1000 AT1000-R3 AT1020 AT1020-R3 AT1025 AT1025-R3 AR1000 AR1000-R3 AR1030 AR1030-R3 AR2000 AR2000-R3 AR2020 AR2020-R3 AR2025 AR2025-R3 AR2010WDMA AR2010WDMA-R3 AR2010WDMB AR2010WDMB-R3 IFS Fiber Module Installation & Operation P/N 1062858 • REV B • ISS 01JUL11
AT1000 AUDIO INPUT 3 2 1 Ground Audio Input Audio Input AR1000 AUDIO OUTPUT 6 5 4 Ground Audio Output Audio Output NOTE: For an unbalanced connection, tie pin 2 to pin 3 and utilize pins 2 and 3 for the audio input to the AT1000 Series module. Utalize pins 1 and 2 for the audio output from the AR1000 Series module.
AT1000 FM AUDIO TRANSMITTER ifs OPTICAL OUT International GRD - 6 Fiber AUDIO OUT - 5 Systems AUDIO OUT - 4 Incorporated GRD - 3 AUDIO IN - 2 AUDIO IN - 1 12 VAC/12 VDC - 3 POWER POWER GRD - 2 12 VAC/12 VDC - 1 *Note: For unbalanced audio input, use the following setup Ground Audio Input Audio Input } Tie together } Audio Output } Balanced Audio Input* Blue Green Brown Simplex multimode fiber optic cable AR1000 FM AUDIO TRANSCEIVER OPTICAL IN ifs International GRD - 6 Fiber AUDIO
AR2000 AUDIO INPUT 6 5 4 3 2 1 AUDIO OUTPUT 6 5 4 3 2 1 Ground Audio Input Audio Input Ground Audio Output Audio Output NOTE: For an unbalanced connection, tie pin 2 to pin 3 and utilize pins 1 and 2 for the audio input to the AR2000 Series module. Utalize pins 4 and 5 for the audio output from the AR2000 Series module.
AR2000 FM AUDIO TRANSCEIVER OPTICAL IN ifs OPTICAL OUT International GRD - 6 Fiber Systems AUDIO OUT - 5 Incorporated AUDIO OUT - 4 GRD - 3 AUDIO IN - 2 AUDIO IN - 1 CARRIER 12 VAC/12 VDC - 3 POWER POWER GRD - 2 12 VAC/12 VDC - 1 *Note: For unbalanced audio input, use the following setup Ground Audio Input Audio Input } Tie together } } Audio Output Balanced Audio Input* Blue Green Brown Duplex multimode fiber optic cable AR2000 FM AUDIO TRANSCEIVER OPTICAL IN OPTICAL OUT ifs Internati
AT1000 A A Power LED AR1000/AR2000 A A B B Carrier LED Power LED NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE CORRECT OPERATIONAL STATUS OF THE UNIT.
AR2000 B A 1 2 3 1 A B C D A 2 3 4 5 6 Power Connector Audio Connector Optical Out Optical In AT1000 B 1 2 3 C 1 2 C 3 A Power Connector B Audio Input Connector C Optical Out A AR1000 B 1 2 3 4 5 6 A Power Connector B Audio Output Connector C Optical In C D
PROPER MOUNTING METHOD FOR THE AT/AR2000 1) Locate unit on solid flat horizontal or vertical surface. 2) Position unit no closer than 24 inches from any power source or machinery. 3) Securely mount unit using (4) four mounting screws (not provided). 4) Attach power wires to terminal block, black wire to PIN 2 and black wire with white stripe to PIN 1. 5) Plug power brick into approved 120v AC outlet. 6) Check power LED to insure device is properly powered, LED will illuminate green.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Sales and support contact information North America Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Copyright Trademarks and patents Manufacturer Certification ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.
