D9110 D9110-R3 D9120 D9120-R3 D9130 D9130-R3 D9110E D9110E-R3 D9120E D9120E-R3 D9130E D9130E-R3 IFS Fiber Module Installation & Operation Instructions P/N 1062846 • REV B • ISS 01AUG11
D9100 SERIES RS - 232 DATA (DTE) 1 2 3 4 5 6 7 12 13 14 15 16 RS - 232 DATA (DCE) 1 2 3 4 5 6 7 12 13 14 15 16 RS - 422 DATA 9 10 11 12 13 14 15 16 17 18 19 20 CONTROL LINES 1 2 3 4 5 6 7 8 9 10 20 21 Data Output Data Input Ground Data Input Data Output Ground + Data Input - Data Input - Data Output + Data Output Ground RTS CTS DSR DCD +5 VDC DTR
D9100 SERIES A/B SWITCH POSITION A 4 3 2 1 Ground Data Out Ground Data In A/B SWITCH POSITION B 4 3 2 1 Ground Data In Ground Data Out
2 1 1 2 Note: The MASTER / SLAVE / BUS switch is functional only on the D9100 Series units, not the D9100E Series units.
REPEATER CONFIGURATION D9130E RS232 OPTICAL TRANSCEIVER INDICATORS RECEIVE A CTS RTS XTMR A CHASSIS GRD DATA IN DATA OUT RTS CTS DATA GRD DSR DCD DTR DTE SW2 REC A RS232 CONNECTOR DCE TRANSMIT A SLAVE MASTER BUS POWER ifs RESET ON ON OFF #1 ON OFF OFF #2 - 1 2 3 4 5 7 6 8 20 International Fiber Systems A Incorporated FAIL B Black wire -2 POWER Black with white stripe + 12 VDC - 1 Duplex single mode fiber optic cable D9130 RS232 OPTICAL TRANSCEIVER INDICATORS REC A RS232 CONNECTOR C
POINT - TO - POINT CONFIGURATION INDICATORS RS232 CONNECTOR RECEIVE A CTS RTS XTMR A CHASSIS GRD - 1 DATA IN -2 DATA OUT - 3 RTS -4 CTS -5 DATA GRD - 7 DSR -6 DCD -8 DTR - 20 DTE SW2 REC A D9130E RS232 OPTICAL TRANSCEIVER DCE TRANSMIT A SLAVE MASTER BUS POWER RESET ifs ON ON OFF #1 ON OFF OFF #2 International Fiber Systems A Incorporated FAIL B POWER -2 + 12 VDC - 1 Black wire Black with white stripe Duplex single mode fiber optic cable INDICATORS RS232 CONNECTOR RECEIVE A CTS RTS X
D9100 A F C B G H J I A B C D E F G H I J K L M Data Receive Channel A Data Transmit Channel A Data Receive Channel B Data Transmit Channel B Reset Switch Receive Channel A CTS (Clear To Send) RTS (Request To Send) Transmit Channel A Power Receive Channel B Transmit Channel B Fail K LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE CORRECT OPERATIONAL STATUS OF
D9100E B A D C I E F H G A B C D E F G H I Data Receive Data Transmit Reset Switch Receive CTS (Clear To Send) RTS (Request To Send) Transmit Power Fail LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates LED illuminates NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE CORRECT OPERATIONAL STATUS OF THE UNIT.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Sales and support contact information North America Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Copyright Trademarks and patents Manufacturer Certification ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.