DE7100-EE DE7100-ME DE7100-SE DE7100-MM DE7100-MS DE7100-SS DE7200-M DE7200-S DE7200-MM DE7200-SS DE7200-MS IFS EtherNav Installation & Operation Instructions P/N 1062843 • REV B • ISS 01AUG11
DE7100 SERIES 10 / 100 MIDI Switch Off (All Electrical Ports) 10 / 100 MIDI Switch On (All Electrical Ports) LOSS OF SIGNAL Fiber Port A LOSS OF SIGNAL Fiber Port B FIBER LINK CONTACTS (All Optical Ports) Transmit + (Pin 1) Transmit - (Pin 2) Receive + (Pin 3) Receive - (Pin 6) NOTE: Pins 4, 5, 7, 8 are not used. Receive + (Pin 1) Receive - (Pin 2) Transmit + (Pin 3) Transmit - (Pin 6) NOTE: Pins 4, 5, 7, 8 are not used.
DE7100 SERIES D A C B H E F A B C D E F G H Fiber port A Fiber port B Link Speed (Channels A&B) Simplex/Duplex (Channels A&B) Power connection Power LOS A&B switch MDI On/Off Fiber link contacts connection I Port connection C I D G GRN = 100 RED or OFF = 10 GRN or YEL = DUPLEX OFF = SIMPLEX LED illuminates with fiber connection
DE7200-M OPTICAL ETHERNET MEDIA CONVERTER 10/100TX 10/100TX NO - 3 CONTACT CLOSURE COM - 2 NC - 1 LNK ACT TX 100FX RX ifs Inter nati onal F i ber Sy s tem s Inc or por ated MDI - 3 NC - 2 LOS B - 1 OFF POWER POWER -2 + 12 VDC - 1 Multimode fiber optic cable DE7100-MS 3 PORT ETHERNET SWITCH TX 10/100TX A 100FX 10/100TX RX NO - 3 CONTACT CLOSURE COM - 2 NC - 1 LNK TX ACT ifs B 100FX RX Inter nati onal F i ber Sy s tem s Inc or por ated MDI - 3 LOS A - 2 LOS B - 1 OFF POWER POWER
IF YOUR POWER OUTLET DOES NOT HAVE A CONNECTION TO GROUND: For proper installation the DE7100-XX stand alone units must be attached to earth ground. Ordinarily, this is accomplished through the power supply. If your power outlet does not have a ground prong then a wire must be attached from the power connector to ground. Connect the green wire included, from ground to the power connector as shown below.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Sales and support contact information North America Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Copyright Trademarks and patents Manufacturer Certification ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.