GE Security GE-DSG-244 DSSG-244 and 244-PoE Managed Ethernet Switch Installation Sheet Package Contents Thank you for purchasing the GE Security GE-DSG/DSSG series of 24-Port Managed Ethernet Switches. The following Switch model numbers are covered in this sheet: • GE-DSG-244 • GE-DSSG-244 • GE-DSSG-244-PoE Open the box of the Managed Switch and carefully unpack it.
System Requirements Your switch is designed to operate with a variety of platforms, operating systems and network cards. Actual performance will depend on a combination of these components. Differences in performance can occur depending on the versions and types of platforms, operating system and network cards used. The minimum system requirements are: • Clients running Windows 98/ME, NT4.0, 2000/XP, Vista, MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols.
Figure 1: Terminal setup diagram A terminal program is required to make a software connection to the GEDSG/GE-DSSG Managed Switch. Windows' Hyper Terminal program is a good choice. The Hyper Terminal program can be accessed from the Start menu. 1. Click START, then Programs/ Accessories and then Hyper Terminal. 2.
Logon to the Console Once the terminal has connected to the device, power on the GE-DSG/GE-DSSG Managed Switch, the terminal will display that it is running testing procedures. Then, the following message asks for the password. The factory default password for the login screen is: • Password: admin Figure 3: Managed Switch Console Login screen Note: For security reasons, please change and memorize the new password after this first setup.
Show the current IP address 1. On "Switch/> " prompt, enter "show ip". 2. The screen displays the current IP address, Subnet Mask and Gateway. As show in Figure 4. Figure 4: IP information Screen Configure IP address 1. On "Switch/> " prompt, enter the following command and press . As show in Figure 5. Switch/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1 The previous command would apply the follow settings for the Switch. IP: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.
Figure 5: IP Setup command 1. Repeat Step 1 to check if the IP address is changed. If the IP is successfully configured, the Managed Switch will apply the new IP address setting immediately. You can access the Web interface of GE-DSG/GEDSSG Managed Switch through the new IP address. Note: If you are not familiar with console command or the related parameter, enter "?" anytime in console to get the help description. 6 of 13 P/N 1069667 • REV 1.
Telnet Setup 1. Connect an RJ-45 cable from the PC to a Switch port on the Managed Switch. Figure 6: RJ-45 connection diagram 2. Enable the Hyper Terminal program. A terminal program is required to make the software connection to the Managed Switch. Windows' Hyper Terminal program is a good choice. Hyper Terminal can be accessed from the Start menu. Click START, then Programs, Accessories and then Hyper Terminal. 3. The following screen will appear. Input a new connection name.
4. Change the Connect using drop-down menu to TCP/IP (Winsock) then input Host address. The Managed Switches default IP address is 192.168.0.100 and the default telnet port number is 23, then press the OK button. Figure 8: The Connect to dialog window Log on to the Console Make sure the device finished booting. Once telnet has connected to the device, hyper terminal will display the login request. Then, the following message asks the login user name and password.
Figure 9: Login request window Now you can configure the Switch by Telnet. Web Browser Setup Start Web Management The following shows how to start up the Web Management of the GE-DSG/GEDSSG Managed Switch. Please note that the Managed Switch is configured through an Ethernet connection, make sure the manager PC must be set on the same IP subnet address. For example, the default IP address of the GE-DSG/GE-DSSG Managed Switch is 192.168.0.100, then the manager PC should be set at 192.168.0.
Figure 10: IP management diagram Login to the managed Switch 1. Use Internet Explorer 6.0 or above Web browser, enter IP address http://192.168.0.100 (the factory-default IP address or that you have just changed in the console) to access the Web interface. 2. When the following dialog box appears, please enter the default password "admin" (or the password you have changed via console). The login screen in Figure 11 appears. • Default IP Address: 192.168.0.
3. After entering the password, the main screen appears as Figure 12. Note: The following screen based on GE-DSG-244 and for GE-DSSG Series, the display will be the same as GE-DSG-244. Figure 12: Main Screen of the Managed Switch 4. Now, you can use the Web management interface to continue the Switch management, please refer to the user manual for more information. Note: For security reasons, please change and memorize the new password after this first setup. P/N 1069667 • REV 1.
Figure 13: Switch Management Options Note: If you are not familiar with Switch functions or the related parameters, press the "Help icon". It is located near the right top of the Web page. Reset Button To reset the IP address to the default IP Address "192.168.0.100" or reset the login password to default value. Press the hardware reset button at the front panel about 10 seconds. After the device is rebooted, you can login the management WEB interface within the same subnet of 192.168.0.xx.
Contact information Thank you for purchase GE Security products. You can browse our online FAQ resource at the GE Security website first to check if it could solve you issue. If you need more support information, please contact GE Security support team. 888 GE Security (888.437.3287) Toll-free in the US, Puerto Rico, and Canada. 503.885.5700 outside of the toll-free area. For contact information see our Web site: www.gesecurity.com. For contact information see our Web site: www.gesecurity.eu.
