User Manual

ManualsBrandsInterlogix ManualsAccessories8-Port 10/100+2 GigE TP/SFP Industrial Full PoE Managed Switch

Table Of Contents

Package Contents
- What’s in the box
- Product Description
- Product Features
- Product Specifications
Hardware Description
- Physical Dimensions
  - GE-DSH-82
  - GE-DSH-82-PoE
- Front / Rear Panel
- Top View
- LED Indicators
Installing the Switch
- Installation Steps
- DIN-Rail Mounting
- Wall Mount Plate Mounting
- Wiring the Power Inputs
- Wiring the Fault Alarm Contact
- Wiring the Digital Inputs / Outputs (GE-DSH-73)
- Installing the SFP transceiver
  - Approved GE Security SFP Transceivers
- Factory Redundant Ring Application
- Transportation Networking and Public Wireless Service
- X-Ring Application
- Coupling Ring Application
- Dual Homing Application
- Connecting to the Console Port
  - DB9/ RJ-45 Connector Pinouts
- Login in the Console Interface
- CLI Management
  - CLI commands and descriptions
About Web-based Management
Requirements
Logging on the Switch
System
- System Information
- IP Configuration
- DHCP Server
- TFTP
- System Event Log
- Fault Relay Alarm
- SNTP Configuration
  - _
- IP Security
- User Authentication
Port Management
- Port Statistics
- Port Control
- Port Trunk
- Aggregator setting
  - Aggregator Information
  - State Activity
- Port Mirroring
- Rate Limiting
Protocol
- VLAN Configuration
- Rapid Spanning Tree Protocol
- RSTP Parameters
- Illustration of STP
- RSTP System Configuration
  - Port Configuration
- SNMP Configuration
- QoS Configuration
- IGMP Snooping
- IGMP Configuration
- X-Ring
Security
- Security-802.1X/Radius Configuration
- MAC Address Table
Digital Input/Output (GE-DSH-73)
- Digital Input
  - Digital Output
Power Over Ethernet (GE-DSH-82-PoE)
- Power over Ethernet Powered Device
- Power Management
Factory Default
Save Configuration
System Reboot
System Commands Set
Port Commands Set
Trunk Commands Set
VLAN Commands Set
Spanning Tree Commands Set
QOS Commands Set
IGMP Commands Set
MAC / Filter Table Commands Set
SNMP Commands Set
Port Mirroring Commands Set
802.1x Commands Set
TFTP Commands Set
SystemLog, SMTP and Event Commands Set
SNTP Commands Set
X-ring Commands Set
PoE Command Set
Address Table
- Learning
- Forwarding & Filtering
- Store-and-Forward
- Auto-Negotiation
What is PoE?
- PoE System Architecture
- How Power is Transferred Through the Cable
  - When to install PoE?
- The PoE Provision Process
- Stages of powering up a PoE link
- Line Detection
- Classification
- Start-up
- Operation
- Power Overloads
- Power Disconnection Scenarios
- DC Disconnect
- AC Disconnect
Switch's RJ-45 Pin Assignments
10/100Mbps, 10/100Base-TX

Chapter 2: Installation

GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 25

2. Lightly push the DIN-Rail into the track.

Figure 2-12: DIN-Rail mounting

3. Check if the DIN-Rail is tightened on the track or not.

4. To remove the industrial switch from the track, reverse above steps.

Wall Mount Plate Mounting

Follow the steps below to mount the Industrial Switch with wall mount plate.

1. Remove the DIN-Rail from the Industrial Switch; loose the screws to remove the

DIN-Rail.

2. Place the wall mount plate on the rear panel of the Industrial Switch.

3. Use the screws to screw the wall mount plate on the Industrial Switch.

4. Use the hook holes at the corners of the wall mount plate to hang the Industrial

Switch on the wall.

5. To remove the wall mount plate, reverse the above steps.