User Manual

ManualsBrandsInterlogix ManualsAccessories8-Port 10/100+2 GigE TP/SFP Industrial Full PoE Managed Switch

Table Of Contents

Package Contents
- What’s in the box
- Product Description
- Product Features
- Product Specifications
Hardware Description
- Physical Dimensions
  - GE-DSH-82
  - GE-DSH-82-PoE
- Front / Rear Panel
- Top View
- LED Indicators
Installing the Switch
- Installation Steps
- DIN-Rail Mounting
- Wall Mount Plate Mounting
- Wiring the Power Inputs
- Wiring the Fault Alarm Contact
- Wiring the Digital Inputs / Outputs (GE-DSH-73)
- Installing the SFP transceiver
  - Approved GE Security SFP Transceivers
- Factory Redundant Ring Application
- Transportation Networking and Public Wireless Service
- X-Ring Application
- Coupling Ring Application
- Dual Homing Application
- Connecting to the Console Port
  - DB9/ RJ-45 Connector Pinouts
- Login in the Console Interface
- CLI Management
  - CLI commands and descriptions
About Web-based Management
Requirements
Logging on the Switch
System
- System Information
- IP Configuration
- DHCP Server
- TFTP
- System Event Log
- Fault Relay Alarm
- SNTP Configuration
  - _
- IP Security
- User Authentication
Port Management
- Port Statistics
- Port Control
- Port Trunk
- Aggregator setting
  - Aggregator Information
  - State Activity
- Port Mirroring
- Rate Limiting
Protocol
- VLAN Configuration
- Rapid Spanning Tree Protocol
- RSTP Parameters
- Illustration of STP
- RSTP System Configuration
  - Port Configuration
- SNMP Configuration
- QoS Configuration
- IGMP Snooping
- IGMP Configuration
- X-Ring
Security
- Security-802.1X/Radius Configuration
- MAC Address Table
Digital Input/Output (GE-DSH-73)
- Digital Input
  - Digital Output
Power Over Ethernet (GE-DSH-82-PoE)
- Power over Ethernet Powered Device
- Power Management
Factory Default
Save Configuration
System Reboot
System Commands Set
Port Commands Set
Trunk Commands Set
VLAN Commands Set
Spanning Tree Commands Set
QOS Commands Set
IGMP Commands Set
MAC / Filter Table Commands Set
SNMP Commands Set
Port Mirroring Commands Set
802.1x Commands Set
TFTP Commands Set
SystemLog, SMTP and Event Commands Set
SNTP Commands Set
X-ring Commands Set
PoE Command Set
Address Table
- Learning
- Forwarding & Filtering
- Store-and-Forward
- Auto-Negotiation
What is PoE?
- PoE System Architecture
- How Power is Transferred Through the Cable
  - When to install PoE?
- The PoE Provision Process
- Stages of powering up a PoE link
- Line Detection
- Classification
- Start-up
- Operation
- Power Overloads
- Power Disconnection Scenarios
- DC Disconnect
- AC Disconnect
Switch's RJ-45 Pin Assignments
10/100Mbps, 10/100Base-TX

Chapter 2: Installation

28 GE-DSH-73/DSH-82 and DSH-82-PoE User Manual

forms an open circuit. The following illustration shows an application example for

wiring the fault alarm contacts.

Figure 2-16: 6-Pin Terminal Block Fault Alarm contact

NOTE: The wire gauge for the terminal block should be in the range between 12 ~ 24

AWG.

Figure 2-17: Power Fault Alarm trigger description

Wiring the Digital Inputs / Outputs (GE-DSH-73)

There is another terminal block comprising two sets of digital input/output contacts

on the topside of GE-DSH-73. Please refer to the Digital Input/Output section for how

to configure Digital Input/Output. The following illustration shows the pin assignment

of the DIDO connector. Please note do not connect DO0/DO1 to the external device

using power higher than 40V/200mA.