IFS SFP Transceiver User Manual P/N 1069181 • REV 1.
Copyright Trademarks and patents © 2014 United Technologies Corporation Interlogix is part of UTC Building & Industrail Systems, Inc. a United Technologies Corporation. All rights reserved The SFP Tranciever name and logo are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Safety Notices The fiber optic SFP transceiver modules are equipped with a Class 1 laser, which emits invisible radiation. Read the following safety warnings carefully. Class 1 Laser Product Complies with FDA Regulation 21 CFR 1040.10 and 1040.11 Class 1 radiation is present when the device or system is powered up. Do not look directly into a laser aperture, as prolonged exposure may cause eye damage.
Content Overview 1 Checklist 2 Installing an IFS SFP Module 3 Connecting the fiber cable 3 Removing the SFP transceiver 4 SFP Specifications 5 Appendix A 9 Fiber Optical Cable Connection Parameters 9 IFS SFP Tranceivers User Manual i
Overview Thank you for purchasing an IFS SFP transceiver. The IFS SFP transceiver can be installed into any IFS network equipment with a 100Base-FX or 1000BaseSX/LX mini-GBIC interface. This user guide provides an overview of the various IFS SFPs (also known as mini-GBIC) transceiver modules available from Interlogix. This user guide also provides instructions for installing, connecting and removing these transceivers.
Checklist The SFP package should contain the following items: • The SFP Transceiver Module x1 • This User Manual x1 If any items are missing or damaged, please consult Interlogix or the dealer/distributor from whom you purchased your SFP transceiver module.
Installing an IFS SFP Module This section describes how to insert an IFS SFP transceiver into a mini-GBIC slot. The IFS SFP transceivers are hot-pluggable and hot-swappable. You can insert and remove an IFS SFP transceiver in any IFS network equipment with a miniGBIC port without having to power down the switch or media converter. As shown in Figure 1.
2. Connect the other end of the cable to a device – i.e. switches with an SFP installed, fiber NIC on a workstation or a Media Converter. 3. Check the LNK/ACT LED of the SFP slot of the switch / converter. Ensure that the SFP transceiver is operating correctly. 4. Check the link mode of the SFP port to see if there is any link failure. With some fiber-NICs or Media Converters, setting the link mode to “1000 Force” or “100 Force” may be needed for proper operation. Removing the SFP transceiver 1.
SFP Specifications The IFS SFP transceivers are available in the following models. Twisted Pair SFP 1000 Base TX GigE Part # Connector Wire Type Max Distance S30-RJ RJ 45 Cat 5e 100M (328 ft) Fast Ethernet 100 Base FX Fiber Connector Part # # of Fibers Fiber Type Max Distance Wave Length Optical Optical Budget Power (dBm) (dBm) Receiver Sensitivitiy (dBm) Operating Temperature S20-2MLC2 LC 2 Multimode 2km (1.
Gigabit Ethernet 1000 Base SX Part # Fiber Connector # of Fibers Fiber Type OM1 & OM2 S30-2MLC LC 2 Multimode 220/550m (720/1800ft) S35-2MLC LC 2 Multimode 220/550m (720/1800ft) Optical Budget (dBm) Optical Power (dBm) Receiver Sensitivitiy (dBm) Operating Temperature 850nm 7.5 -9.5 ~ -1 -17 0 to + 50C (32 to 122F) 850nm 7.5 -14 ~ -8 -17 -40 to +75C (-40 to 167F) Max Distance Wave Length OM1/OM2 OM1 Multimode fiber @ 200/500MHz-km OM2 Multimode fiber @ 500.
Gigabit Ethernet 1000 Base ZX Part # Fiber Connector # of Fibers Fiber Type Max Distance Wave Length Optical Budget (dBm) Optical Power (dBm) Receiver Sensitivitiy (dBm) Operating Temperature S30-2SLC-70 LC 2 Single Mode 70km (43mi) 1550nm 19* -15 ~ -8 -34 0 to + 50C (32 to 122F) S35-2SLC-70 LC 2 Single Mode 70km (43mi) 1550nm 19* -15 ~ -8 -34 -40 to +75C (-40 to 167F) * Note: High Power Optic. There must be a minimum of 5dB of optical loss to the fiber for proper operation.
10GBase-SR SFP+ Part # Fiber Connector # of Fibers Fiber Type OM3 Max Distance OM3 Wave Length Optical Budget (dBm) Optical Power (dBm) Receiver Sensitivitiy (dBm) Operating Temperature S40-2MLC LC 2 Multimode 300m* 850nm 10 -7.3 ~ -1 -11 0 to + 50C (32 to 122F) *OM3 Multimode fiber @ 2000/500MHz-km Optimized got 850nm VCSELs maximum distance of 300m.
Appendix A Fiber Optical Cable Connection Parameters The wiring details are as below: • Fiber Optical patch Cables: Standard Fiber Type Cable Specification 1000Base-SX (850nm) Multi-mode 50/125μm or 62.5/125μm 1000Base-LX (1310nm) Single mode 9/125μm 1000Base-LX (1550nm) Single mode 9/125μm Multi-mode 50/125μm or 62.
