Spec Sheet

ManualsBrandsInterlogix ManualsFiber Optic TransmissionD1300 IFS RS-485 2-Wire Point-to-Point Data Transceivers

D1300 Series

IFS RS-485 (2-wire) Point-to-Point

Data Transceivers

IFS

Line / Fiber Transmission

interlogix.com

STANDARD FEATURES

• Meets EIA RS-485 Speciﬁcations

• Tested and Certiﬁed by an Independent Testing Laboratory for

Full Compliance with the Environmental Requirements (Ambient

Operating Temperature, Mechanical Shock, Vibration, Humidity

with Condensation, High-Line/Low-Line Voltage Conditions

and Transient Voltage Protection) of NEMA TS-1/TS-2 and the

Caltrans Speciﬁcation for Trafﬁc Signal Control Equipment.

• Automatic Resettable Solid-State Current Limiters

• Power, Transmit and Receive Data Status LED Indicators

• No In-ﬁeld Electrical or Optical Adjustments Required

• Data rates up to 150 kbps NRZ

• Data Re-clocking

• Transparent to Data Encoding / Compatible with Major Data

Protocols

• Point-to-Point Network Architecture

• 2-Wire (Half-Duplex)

• True Tri-State Output

• Hot-Swappable Rack Modules

• Distances up to 20 Miles (33 km)

• Comprehensive Lifetime Warranty

D1300

Control

Data

Control

Data

Host

2 Fibers

62.5/125μm MM

D1300

up to 1.9 miles

(3 km)

ifs

International

Fiber

Systems

Incorporated

203.426.1180

ifs

International

Fiber

Systems

Incorporated

203.426.1180

Speciﬁcations

Data

Data Interface: RS-485 (2-wire)

Data Rate: DC - 150 Kbps*

Total Network Pulse Distortion: <1μs

*-HS Option Data Rate: DC - 400 Kbps

Wavelength D1300 and D1300WDMB: 850 nm, Multimode

All others: 1310 nm, Multimode or Single Mode

NumberOfFibers 2

Connectors

Data and Power: Terminal Block with Screw Clamps

Optical: ST

Electrical&M echanical

Power:

Surface Mount: 12 VDC @ 200 mA to 24 VDC @ 100 mA

Rack: From Rack

Number of Rack Slots: 1

Current Protection: Automatic Resettable Solid-State Current Limiters

Circuit Board: Meets IPC Standard

Size (in./cm.) (LxWxH)

Surface Mount: 7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm

Rack Mount: 7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm

Shipping Weight: < 2 lbs./0.9 kg

Environmental

MTBF: > 100,000 hours

Operating Temp: -40° C to +74° C

Storage Temp: -40° C to +85° C

Relative Humidity: 0% to 95% (non-condensing)†

†May be extended to condensation conditions by adding suﬃx ‘–C’ to

model number for conformal coating.

System Design

PartNumber

Opt.Pwr.Budget

Max.Distance*

Multimode

62.5/125μm**

Single Mode

9/125μm

1.9 miles (3 km)

6 miles (10 km)

20 miles (33 km)

PS-12VDC 12 Volt DC Plug-in Power Supply (Included)

PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if speciﬁed at time of order)

Add ‘-24’ for 24 VDC Power (Extra charge, consult factory)

Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)

Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)

Add ‘-HS’ for High Speed Data Rates up to 400 Kbps (Extra charge, consult factory)

D1300

D1300WDMA

D1300WDMB

D1320

D1325

11 dB

10 dB

11 dB

FibersRequired

RS-485 Data Transceiver (850 nm)

RS-485 Data Transceiver (1310 nm)

Data Transceiver (1310 nm)

Description

Ordering Information

Made in the USA

Complies with FDA Performance

Standard for Laser Products, Title 21,

Code of Federal Regulations, Subchapter J

*Optical transmission distance is limited to optical loss of the ﬁber and any additional loss introduced by connectors, splices and patch panels.

Distance can also be limited by ﬁber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ♦All accessories are third party manufactured.

Accessories♦

Options

Security

North America

T 888-GE-SECURITY

888-437-3287

F 503-691-7566

E sales@ifs.com

Asia

T 852-2907-8108

F 852-2142-5063

Australia and New Zealand

T 613-9239-1200

F 613-9239-1299

Europe

T 32-2-719-9847

F 32-2-719-9846

Latin America

T 305-593-4301

F 305-593-4300

gesecurity.com/ifs

Speciﬁcations subject to

change without notice

Agency compliance

OVERVIEW

he IFS D1300 Series data transceivers provide point-to-point

transmission of half-duplex (2-wire) EIA RS-485 tri-state data signals

over one or two optical ﬁbers. The transceivers are transparent to

data encoding allowing for broad-range compatibility. When used

as a line-terminating device, these modules are also compatible

th the IFS D2300 Series drop and repeat data transceivers.

Models within this series are available for use with multimode or

single mode optical ﬁber. Plug-and-play design ensures ease of

installation requiring no electrical or optical adjustments. Each

transceiver incorporates power and transmit/receive data status

indicating LED’s for monitoring proper system operation. The

modules are available in either stand-alone or rack mount versions.

APPLICATION EXAMPLES

• Access Control Systems

• Building Automation and Environmental Control Systems

• Computer/Data Equipment

• Fire & Alarm Systems

• ITS Trafﬁc Signalization Networks

SYSTEM DESIGN

Summary of content (2 pages)

PAGE 1
IFS® Line / Fiber Transmission D1300 Series IFS RS-485 (2-wire) Point-to-Point Data Transceivers Speciﬁcations Data Data Interface: Data Rate: Total Network Pulse Distortion: *-HS Option Data Rate: RS-485 (2-wire) DC - 150 Kbps* <1μs DC - 400 Kbps D1300 and D1300WDMB: 850 nm, Multimode All others: 1310 nm, Multimode or Single Mode Wavelength OVERVIEW STANDARD FEATURES 2 NumberOfFibers The IFS D1300 Series data transceivers provide point-to-point • Meets EIA RS-485 Specifications • Tested and Certif
PAGE 2
D1300 Series North America T 855-286-8889 Latin America T 561-998-6114 IFS RS-485 (2-wire) Point-to-Point Data Transceivers Ordering Information Multimode 62.5/125µm** Part Number Description Fibers Required Optical Pwr. Budget Max. Distance* D1300 RS-485 Data Transceiver (850 nm) 2 11 dB 1.9 miles (3 km) D1300WDMA RS-485 Data Transceiver (850 nm) 1 11 dB 1.9 miles (3 km) D1300WDMB RS-485 Data Transceiver (1310 nm) 1 11 dB 1.