IS-ZW-TSTAT-300 Advanced Thermostat Operation Guide Content Contact information 1 Description 2 Home screen 3 Menu screen 3 Program screen 5 Manual screen 6 Initial settings 7 Auto-run program 7 Other functions 8 Communicating thermostat 9 Specifications 10 Contact information For contact information, see www.interlogix.com. © 2013 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved.
Description The IS-ZW-TSTAT-300 programmable communicating thermostat operates via a high-quality, easy-to-use touch screen. To program or adjust your thermostat, simply touch your finger firmly to the screen. The screen will automatically light up and you will hear a “beep”. The screen will respond differently to different types of touches, so you may want to experiment by touching it different ways, finger, fingernail, etc. Do not use a sharp or metallic device; it will scratch the screen.
Home screen The Home screen is displayed when the unit is operating. This screen shows you the current settings and conditions. Figure 2: Home screen Time of day Fan status Time slot RADIO Lock status LINK Chirp indicator Radio indicator Target temperature Thermostat mode TARGET TEMP Current room temperature Day To set a mode, press the MODE button on the side of the thermostat. The thermostat will step through the HEAT, OFF, and COOL modes in order.
Time of day Touch the left (down) or right (up) arrows next to the time display to set the current time (1 minute per touch). Touch and hold the arrow for fast time set (15 minute jumps). Day of week Touch the Day area to select the present day. FILTER The thermostat can be programmed to remind you when the HVAC system’s air filter needs changing. Touch FILTER. The display will show the usage to date. Touch FILTER for over 3 seconds and the display will change to LIMIT.
For full lock, touch the Lock icon again for 5 seconds to go to Full Lock mode (Lock icon with two bars). No changes can be made. Once locked, the thermostat will respond just to mode and menu. To unlock, press the Menu button. Touch and hold the Lock icon for 5 seconds for two bars (if not there already). Then touch and hold the Lock icon for another 5 seconds. Each 5-second touch and hold must be separate. Home icon Return to the Home screen.
Manual screen Touch the large current temperature display on the middle of the Home screen to access the Manual screen. You can use the Manual screen to make temporary changes to your thermostat’s operation. Note: The mode must be in HEAT or COOL to access the Manual screen.
EMER (heat pump only) If you set your thermostat for HEAT PUMP with auxiliary heat, the EMER function is available on the Manual screen. If you touch EMER, it displays EMER|ON. You heat pump is disabled and auxiliary heat is your sole source of heat. This manual override stays active until you toggle EMER off. Auxiliary heat is more expensive than the heat pump, so use EMER only if the heat pump cannot keep up or is defective. Home icon Touch to return to the Home screen.
Table 1: EPA program MORN DAY EVEN NITE HEAT 6:00am 8:00am 6:00pm 10:00pm All Days 70 F 62 F 70 F 62 F MORN DAY EVEN NITE COOL 6:00am 8:00am 6:00pm 10:00pm All Days 78 F 85 F 78 F 82 F To change the program Make sure the thermostat mode is set to either HEAT or COOL, then press the Prog button to display the Program screen. The programmed start time is displayed on the upper left. The Time Slot icon indicates the active time slot in the default program (MORN, DAY, EVEN, NITE).
feature, press the Save Energy button in the upper left corner of the unit. The screen will now read “Save Energy”. To return to normal operation, press the Save Energy button again. This is useful to save energy if your are going to be gone for a short time. MODE button The MODE button sets the thermostat to HEAT, COOL, or OFF modes. Press it once to step to the next mode. If the thermostat is in OFF mode and you want to return to the mode you were previously in, touch the OFF indicator on the screen.
Figure 6: USNAP radio and port USNAP radio USNAP port The USNAP ports allow you to connect your Thermostat to your home Z-Wave network. This can give you access to your home’s HVAC system even when you are away (with additional web service). It can also give you access to web based efficient energy management sites that can help you save money and protect the environment.
Statement of use: 100% compatible with all popular residential HVAC systems; 24 VAC single, twostage conventional heating systems (gas/oil/electric), heat pumps, single stage or auxiliary heat (electric or fossil), zoned forced air and zoned hot water (two or three wire), millivolt systems (with a 12-24 AC or DC source), one or two stage cooling, and hybrid systems.
IS-ZW-TSTAT-300 Advanced Thermostat Operation Guide
