KTD-400 Controller Keypad User Manual KTD-400 GE Security
Copyright Copyright © 2006, GE Security Inc. All rights reserved. This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from GE. Document number/ 1034790E (March 2006). Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
iii Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Conventions used in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Safety terms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv KTD-400 Controller Keypad User Manual
1 Preface This is the GE KTD-400 Controller Keypad User Manual for models KTD-400 and KTD-300R. This document includes an overview of the product and detailed instructions explaining: • • how to install and program; and how to operate the KTD-400 and KTD-300R. There is also information describing how to contact technical support if you have questions or concerns.
2 KTD-400 Controller Keypad User Manual Product overview The KTD-400 Controller Keypad is designed for use in a Digiplex system. The KTD-400 can address and control 512 pan/tilt/zoom (PTZ) receiver sites, operate a matrix switcher with 64 monitor outputs, and address/ select views from as many as 64 multiplexers and VCRs. Several modes of multiplexers are supported. Note: For CyberDome control with the KTD-400, pan/tilt operation is limited to three speeds.
3 Installation To install a KTD-400 keypad, you will need to set the DIP switches, mount the unit (KTD-300R only), and wire the device. CAUTION: Do not connect power to the unit before all installation steps have been completed. Do not connect directly to a telecommunication network. DIP switch settings Use Table 1 to select your mode of operation. Table 1. DIP switch settings Setting Binary Description 1000 Digiplex PTZ and VCR control only.
4 KTD-400 Controller Keypad User Manual Mounting the KTD-300R The KTD-300R is designed to fit into a standard EIA 19-inch rack and uses one unit (1.75 in.) of rack space. Mount the unit using the four holes in its front panel and hardware provided from the rack manufacturer. Wiring connections The KTD-400 comes with a 6 ft. (1.8 m) cable that attaches to a modular phone box (Figure 4). All external connections are made in the phone box.
5 KTS-41 system control Wiring the KTD-300R to control a KTS-41A system involves connecting the RS-422 input cable (if used), the RS-422 output cable (if used), the DTMF output cable (to the KTS-41A), and the 12 VDC wall transformer (Figure 6). Figure 6.
6 KTD-400 Controller Keypad User Manual KTD-400 configuration After you install and power up your KTD-400 keypad, you will need to configure it to operate within your systems. You can also use the KTD-400 to configure other components in the Digiplex system. (See System component configuration on page 10.) The KTD-400 offers many programming choices that identify how it will function in the system. A separate code is used to access the menus.
7 3. The clear memory option (Figure 10) will erase all data in the controller keypad’s nonvolatile memory and reload the factory default values. • • If you do not want to clear the memory, press 0. This will advance you to the system size display (Figure 11). To clear the controller keypad’s memory, press 1. This will advance you to the confirmation display. Press 3 to reload the controller keypad’s memory with factory default values. If you do not want to clear the memory, press 0.
8 KTD-400 Controller Keypad User Manual 6. Use the menu in Figure 13 to deny or permit the controller keypad’s access to certain monitors. Press 0 to deny access or 1 to permit access. After each selection, the next monitor number will appear. Use the up and down directional arrows to move between monitors. When done, press Seq to advance to the next menu. 7. The menus in Figure 14 let you select which multiplexers can be enabled from the keypad.
9 9. The menu in Figure 16 lets you select which VCRs can be can be enabled from the keypad. This display will only come up if your system has at least one VCR. • • • Figure 16. VCR access display VCR 01 ACC=YES 0=NO 1=YES SEQ=NEXT If you don’t want to enable any VCRs, press Seq to advance to the maximum preset display (Figure 17). Press 0 to advance to the next VCR, or use the up and down arrows to move between VCRs. Press 1 to enable a VCR.
10 KTD-400 Controller Keypad User Manual System component configuration After you have completed the KTD-400 keypad configuration, you can used the keypad to configure other Digiplex system components. To configure these system components, begin at the normal operating display and do the following: 1. In the normal operating display shown in Figure 19, press and hold the Set key until the display in Figure 20 appears. 2. In the menu in Figure 20, enter the access code 9, 5, 1, Seq.
11 PTZ receiver configuration Each PTZ receiver offers modes of operation choices, many of which can be programmed using a KTD-400 series keypad. It can also store preset position information if applicable. To program a PTZ receiver, complete the steps in System component configuration on page 10, press 2 at the component programming selection menu (Figure 21 on page 10), then do the following (for all cameras): 1.
12 KTD-400 Controller Keypad User Manual 6. Use the menu in Figure 27 to reverse the pan and tilt directions for cameras that must be mounted in an inverted position. Press 1 to invert or 0 for normal pan/tilt operation. The next display will appear. 7. The next three menus provide choices for defining the polarity of the output voltage for the motorized lens connected to the receiver. a. For zoom direction, press 0 if the lens requires positive voltage for zoom in and negative voltage for zoom out.
13 PTZ receiver preset position programming If a PTZ receiver or a KTA-12 series PTZ dome is equipped for preset camera positioning (P option), the receiver can store 10 preset positions in its nonvolatile memory. You can call each preset position individually and include each in a preset tour (camera automatically pans, tilts, zooms, and focuses through a series of preset positions).
14 KTD-400 Controller Keypad User Manual Operation A KTD-400 series keypad can address and control 512 PTZ receiver sites, operate a matrix switcher with 64 monitor outputs, address and select views from 64 multiplexers, and control 64 VCRs. It can also be used to control a KTS-41 Mini-Matrix switcher. Key layouts Figure 34 shows the key layout for the KTD-400. Figure 34.
15 Key functions PTZ control keys Zoom in, Zoom out Used to control the zoom function of the selected receiver site’s motorized lens. Focus near, Focus far Used to control the focus function of the selected receive site’s motorized lens. Also used to disengage the autofocus feature on the CyberDome. Iris open, Iris close Used to control the iris function of the selected receiver site’s motorized lens. Also used to enable the Backlight compensation option.
16 KTD-400 Controller Keypad User Manual Site select keys 0 to 9 Numerical keys are used for camera and monitor selection in Digiplex operation mode, or camera and multiplexer selection in multiplexer operation. Also used for preset position selection when applicable. Clear Refreshes the alphanumeric display on the selected monitor. Also used to clear infinite alarms using numerical keys. Set Used in combination with a numerical key (0 through 9) to find preset positions.
17 Keypad operation When power is first supplied to a KTD-400 series keypad, the LCD display will briefly display the company name, and then show the normal operating display (Figure 36). Figure 36. KTD-400 normal operating display CAMERA 000 MONITOR 01 From this display and by observing the system’s monitors, you can use the function keys for control. Monitor selection To select a monitor, press Mon and use 0 through 9 to enter the desired number. For example to select monitor 12, press Mon, 1, 2.
18 KTD-400 Controller Keypad User Manual Camera sequencing To place a monitor in the sequence mode, select the monitor and press Seq. The display shown in Figure 37 will appear in the keypad’s display window. Figure 37. Sequence selection ENTER SEQUENCE NUMBER? - (1, 2, 3, 4) Use 1 through 4 to enter the desired sequence tour. Setting electronic autopan limits for domes To set the electronic autopan limits on dome receivers, first position the dome at the limit.
19 Multiplexer operation The Mode key toggles the KTD-400 between normal operation mode, multiplexer operation mode, and VCR operation mode. Switching to multiplexer control mode To enter the multiplexer operation mode, press Mode once and the display shown in Figure 39 appears. Figure 39. Multiplexer operation mode MULTIPLEXER 01 VIEW -- The keypad is now able to control multiplexers.
20 KTD-400 Controller Keypad User Manual Selecting multiple camera views on a multiplexer Press View to step the active multiplexer between those views programmed to be available for that multiplexer. Each time you press View, the next available view will be displayed by the multiplexer. Refer to the installation and operation documentation provided with the multiplexer to determine available views.
21 Contacting technical support For assistance installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, you may contact technical support during normal business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Table 2. Sales and support contact information Sales Phone Technical support Toll-free: 888.GESECURity (888.437.
22 KTD-400 Controller Keypad User Manual
23 Index A alarms M multiplexer control mode........................................................................19 clearing alarms...................................................................................18 video alarms .......................................................................................18 multiplexer operation..............................................................................19 MV96 multiplexer...................................................................
24 KTD-400 Controller Keypad User Manual