IFS MC250-1T/1S User Manual P/N 1072573 • REV 00.
Copyright © 2013 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Intended use Manufacturer The IFS MC250-1T/1S and logo are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Contents Overview 1 Package Contents 1 Product Features 2 Installation 3 Product Description 3 Front Panel 5 LED Indicators 6 Converter Top Panel 7 Wiring the Power Inputs 7 Wiring the Fault Alarm Contact 8 Mounting Installation 9 Installation Steps 13 Switch Operation 14 Troubleshooting 16 Specifications 17 RJ45 Pin Assignments 18 Contacting Technical Support 20 IFS MC250-1T/1S User Manual i
Overview This section describes the functionalities of the IFS MC2501T/1S Industrial Media Converter’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. In the following section, the term “Industrial Media Converter” means the IFS MC250-1T/1S.
Product Features Physical Port MC250-1T/1S 1-Port 10/100Base-TX RJ-45 1-Port 100Base-FX SFP slot (Distance depends on SFP module) Industrial Design Slim type IP-30 metal case -40 to +75 Degree C operating temperature DIN rail and wall mount design 12 to 48V DC, redundant power with polarity reverse protection and detachable terminal block connectors for master and slave power Supports EFT protection 6000V DC for power line Supports 6000V DC Ethernet ESD protection Data Communication Compl
Installation This section describes the functionalities of the Industrial Fast Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. In the following section, the term “Industrial Fast Ethernet Switch” means the MC250-1T/1S. Product Description The MC250-1T/1S is an industrially hardened media converter which is specially designed to operate from -40 to 75℃ temperature.
With the Fast Ethernet SFP interface, the MC250-1T/1S extends the transmission distances from 220m to 70Km. The actual distance is defined by the Fast Ethernet SFP module selected. The IFS family of Fast Ethernet SFP modules comes with one of the following models. The following list shows the available Modules for MC250-1T/1S.
Front Panel The figure below shows the Front Panel of the MC250-1T/1S.
LED Indicators System LED Color Function P1 Green Indicates that power 1 is on. P2 Green Indicates that power 2 is on. Fault Green Indicates either power 1 or power 2 has no power. Per 10/100Base-TX Port LED Link / ACT Color Function Light Indicates that the link through that port is successfully established at 100Mbps. Blink Indicates that the Switch is actively sending or receiving data over that port.
Converter Top Panel The top panel of the MC250-1T/1S consists of a terminal block connector with two DC power inputs. Wiring the Power Inputs The 6-contact terminal block connector on the top panel of the MC250-1T/1S is used for two DC redundant powers inputs. Please follow the steps below to insert the power wires. 1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. V1- V1+ V2- V2+ 2.
1 - 2 Power 1 3 4 5 Fault 6 Power 2 + - + Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the MC250-1T/1S will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
Mounting Installation This section describes how to mount the MC250-1T/1S and make connections to it. Please read the following section and perform the procedures in the order presented. Note: In the installation steps below, this Manual uses the IFS 8 Port Industrial Gigabit Switch, GE-DSGH-8, as an example. However, the steps for any IFS Industrial Switch & Industrial Media Converter are similar. Mounting to a DIN-Rail The DIN-Rail kit comes assembled on the MC250-1T/1S out of the box.
1. Lightly press down and push the bottom of the DIN-Rail connector mount into the track. 2. Check that the DIN-Rail connector mount is tightly mounted on the track. 3. Please refer to following procedures to remove the MC2501T/1S from the track.
4. Lightly press down and pull the bottom of DIN-Rail connector mount to remove it from the track. Mounting to a Wall To install the MC250-1T/1S on the wall, please follow the instructions described below. 1. Loosen the screws to remove the DIN Rail from the Media Converter.
2. Place the wall mount plate on the rear panel of the MC2501T/1S. 3. Assemble the wall mount plate on the MC250-1T/1S 4. Use the hook holes at the corners of the wall mount plate to hang the MC250-1T/1S on the wall.
Installation Steps Step 1: Unpack the Industrial Fast Ethernet Switch. Step 2: Check that DIN-Rail is screwed on the Industrial Fast Ethernet Switch. (Please refer to the DIN-Rail Mounting section for DIN-Rail installation. If you want to wall mount the Industrial Fast Ethernet Switch, then please refer to Wall Mount Plate Mounting section for wall mount plate installation.
Switch Operation Address Table The Industrial Fast Ethernet Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of each node in the network, including MAC address, Port No., etc. This information comes from the learning process of the Industrial Fast Ethernet Switch.
from the frames before transmission. Lack of error packet occurrence is important for an efficient and stable network.. The Industrial Fast Ethernet Switch scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers directly to the network, thereby increasing throughput and availability.
Troubleshooting This chapter contains information to help resolving issues. If the Industrial Fast Ethernet Switch is not functioning properly, make sure the device was set up according to instructions in this manual. The Link LED is not light Solution: Check the cable connection of the Industrial Fast Ethernet Switch. Performance is bad Solution: Check the speed duplex mode of the partner device.
Specifications Product MC250-1T/1S Hardware Specification 10/100Base-TX Port 100Base-FX Port 1 RJ-45 Auto-MDI/MDI-X port 1 SFP Slot Fiber Port Type Cable Distance Optical Frequency Launch Power (dBm) Receive Sensitivity (dBm) Maximum Input Power (dBm) Dimension (W x D x H) Deprends by SFP module 135mm x 85mm x 32mm 430g Weight Installation DIN rail kit and wall mount ear Maximum Frame Size 1522bytes packet size Flow Control Back pressure for half duplex, IEEE 802.
When connecting to other Ethernet equipment such as a Router, Bridge, Switch, or Hub, please refer to that device’s Technical Manual.
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network.
Contacting Technical Support Contact technical support if you encounter any difficulties during this installation. Please make sure you have the requested diagnostic or log files ready before you contact us by phone or go to www.interlogix.com/customer-support. Technical Support Europe, Middle East and Africa W Select Contact Us at www.utcfssecurityproducts.eu North America T +1 855.286.8889 E techsupport@interlogix.com Australia E 20 techsupport@interlogix.
