Manual

ManualsBrandsInterlogix ManualsSafetyNX-148E-RF

P/N 466-2198 • REV F • OCT12

NX-148E-RF LCD Touchpad with Receiver

Installation Instructions

Content

Contact information 1

Product summary 1

Installation 2

Transmitter programming 2

Touchpad programming 5

Reference tables 9

Specifications 14

Regulatory information 14

Contact information

www.utcfireandsecurity.com or www.interlogix.com

For customer support, see www.interlogix.com/customer-

support

Interlogix is part of UTC Climate Controls & Security, a unit of

United Technologies Corporation.

Product summary

The NX-148E-RF Touchpad with Receiver combines touchpad

and receiver capabilities into a single device for use with all

NetworX control panels except CF (commercial fire) panels.

Note: When using this touchpad with an NX-8E, NX-8V2, NX-

6V2, or NX-4V2 and downloading via modem, make sure the

control panel version is equal to or greater than the following

versions:

• NX-8E 17.00

• NX-8V2 1.04

• NX-6V2 1.05

• NX-4V2 1.04

Make sure you are using DL900 version 2.11 or greater

software.

Installation guidelines

Use the following installation guidelines:

• Mount transmitters as close as possible to the touchpad.

For best results, we recommend the distance between the

transmitter and the touchpad be less than 100 ft. (30.5 m).

• Mount the touchpads in an environmentally controlled area

with a temperature range from 32 to 120°F (0° to 49°C).

• When mounting the touchpad, allow at least 3 in. (7.6 cm)

below the touchpad for the swing-down door (Figure 1).

Figure 1. Side view

• Use Table 1 to determine the maximum wire lengths

allowed between the touchpad and the panel.

Tools and supplies needed

• Pencil

• Phillips screwdriver

• Drill

• 15/64 in. drill bit

• Mounting screws (provided)

• Wall anchors (optional)

• 4-conductor, 22, 18, 16, 14 or 12-gauge wire (see Table

1).

Summary of content (14 pages)

PAGE 1
NX-148E-RF LCD Touchpad with Receiver Installation Instructions Content Contact information 1 Product summary 1 Installation 2 Transmitter programming 2 Touchpad programming 5 Reference tables 9 Specifications 14 Regulatory information 14 Installation guidelines Use the following installation guidelines: • Mount transmitters as close as possible to the touchpad. For best results, we recomm end the distance between the transmitter and the touchpad be less than 100 ft. (30.5 m).
PAGE 2
Installation To install the touchpad, do the following: 1. Remove the mounting-plate screw (Figure 1) from the bottom of the touchpad and lift off the mounting plate. Caution: You must be free of static electricity before handling circuit boards. Wear a grounding strap of touch a bare metal surface to discharge static electricity. 2. At the mounting location, use the mounting plate to mark the location for the antenna and mounting holes (Figure Table 1: w iring guidelines Length Wire gauge 250 ft.
PAGE 3
RM: receiver module 4. To load factory default s and clear unwant ed informat ion in memory for new installat ions, enter 9 1 0 #. 5. To determine the starting zone number for the specific touchpad receiver on new installations, set the receiver zone bank (Location 594) The bank setting is based on the zone capabilities of both the receiver and the panel and must be set before you add (learn) transmitters. 6. Enter 400 # to enter the sensor (transm itt er) learnin g location. 7.
PAGE 4
9. To program remaining transmitters, repeat steps 6 to 8. 6. To continue programming keyfob transmitter partition settings, repeat steps 4 to 8. 7. To exit program mode, press EXIT EXIT. 10. To exit program mode, press EXIT EXIT. Transmitter options Door/window transmitter settings To set features 4 (Input option 1) and 5 (Input option 2) for door/window transmitters, do the following: • To disable the transmitter’s internal reed s witches, turn on feature 4.
PAGE 5
4. Enter the zone location and press #. For example, enter 407 # to delete zone 7. 6 Assign user authority 7 Reset function 5. To change transmitter feature 1 (Transmitter enabled), enter 1 and press *. The 1 turns off to indicate the feature change.
PAGE 6
Service menu (2) A Service Required message will display periodically if the system requires service. To access the service menu, do the following: 1. device such as an NX-507E, NX-508E, NX-534E or NX-540E), do the following: 1. Enter * 47. 2. Enter your program code. Enter * 2 to display one or more of the fault messages in Note: Use * key to select light number. Table 9. 2. Press or to scroll through the messages. 3. To exit the service messages, press # #.
PAGE 7
Assign user authority (6) Adjust view/brightness of LCD (91) To assign user authority levels, you must have authority over To adjust the view and brightness of the LCD display, do the the assigned partitions. To assign user authority, do the following: following: 1. Enter * 6. 2. Enter your master code. 3. Enter the user number. 4. Use keys 1 (yes) and 0 (no) to assign authorities when 1. Enter * 91. 2. Enter your master code. 3.
PAGE 8
Table 7. Editing character data 12 Select an option - Programs special characteristics. Com mand Action 1 = Display Press * For Help * Saves character or word. Moves cursor to the right. 2 = Disable LED extinguish on this touchpad CANCEL Moves cursor to the left. 3 = On if PIN should be hidden w hen programming Scrolls through available characters. In library mode, scrolls through available w ords. 4 = On suppresses beeps when an RF Transmission is lost. STAY Inserts a black space.
PAGE 9
Silent exit (EXIT) Zone trouble, press * To silence the exit beeps during exit delay (while the system is A zone is experiencing trouble. Press * to identify the zone. disarmed), do the following: Table 10. Log m essages 1. Enter * EXIT. 2. Enter your user code. 3. To exit, press #. Reference tables Table 9. Service menu messages Display Description TXlobat Transmitter low battery ZN Lost Zone lost - A w ireless multiplexed zone device is not reporting to the control.
PAGE 10
Man Test Manual test - Bell and/or communicator test w hile system is disarmed. Zone _____ Re-exit The exit delay has been restarted w ithout disarming the system. Assigned to module #_____. Output Trip A trip has occurred on an expander auxiliary output. Data Lost Communication of a signal has failed (log only event). Walk-test A zone Walk Test mode has been activated. End Test Test has ended. Cross-Trip The first zone of a cross zone has been tripped (log event only).
PAGE 11
Zone _____ Assigned to module #_____. RM HE P Zone _____ Assigned to module #_____.
PAGE 12
Zone _____ Assigned to module #_____. RM HE P Zone _____ Assigned to module #_____.
PAGE 13
Zone _____ Assigned to module #_____. RM HE P Zone _____ Assigned to module #_____.
PAGE 14
Specifications Compatibility Compatible w ith all Netw orX control panels except CF (commercial fire) panels Frequency 319.5 MHz Wireless range 600 feet (183 m) open air Required pow er 12.0 VDC (provided by panel) Current draw 75 mA maximum Operating temperature 32 to 120°F (0 to 49°C) Storage temperature -30 to 140°F (-34 to 60°C) Humidity 90% relative noncondensing Dimensions 5 x 6 x 1 in. (12.7 x 15.2 x 2.