Installation Manual

ManualsBrandsInterlogix ManualsAlarms AccessoriesQuik Bridge Non-supervised 2-CH Receiver

Page 1

INSTALLATION

INSTRUCTIONS

Quik Bridge ® Two-Channel Receiver

Product Summary

The Quik Bridge® Two-Channel Receiver allows two

zones of a hardwired panel to use wireless devices. This

allows you to add up to four wireless sensors and /or

Keychain Touchpads to the hardwired system. You may

assign the wireless devices to the two receiver zones in

any combination (4 on zone 1 and 0 on zone 2, 3 on zone

1 and 1 on zone 2, etc.). See the diagrams below for some

suggested uses for this receiver. The letters by each Key-

chain Touchpad represent the button modes (see Tabl e3)

you must enter into the receiver. The receiver recognizes

each button mode as a separate device.

1) Expanding zones by adding

sensors

2) Expanding zones, and remote

level-sensitive keyswitch arm-

ing

3) Expanding zones, and control-

ling one garage door opener

HARDWIRE

ZONE

HARDWIRE

ZONE

9217G15A.DSF

9217G16A.DSF

ZONE

HARDWIRE

ZONE

ZONE FOR

KEYSWITCH

ARMING

9217G17A.DSF

GARAGE

DOOR

HARDWIRE

ZONE

60-760

Quik Bridge

Two-

Channel Receiver

Document Number: 466-1547 Rev. C

September 1999

9217G07A.DS

Summary of content (14 pages)

PAGE 1
Quik Bridge® TwoChannel Receiver Quik Bridge ® Two-Channel Receiver Document Number: 466-1547 Rev. C September 1999 9217G07A.DSF 60-760 INSTALLATION INSTRUCTIONS Product Summary The Quik Bridge® Two-Channel Receiver allows two zones of a hardwired panel to use wireless devices. This allows you to add up to four wireless sensors and /or Keychain Touchpads to the hardwired system.
PAGE 2
Quik Bridge ® Two-Channel Receiver 4) Controlling one garage door opener, and level-sensitive remote keyswitch arming* 5) Controlling two garage door openers, each using a separate touchpad D+H D+H ZONE 1 2 ZONE FOR KEYSWITCH ARMING GARAGE DOOR Edge-sensitive switch arming Q or W L H ZONE 6) ZONE ZONE 1 2 Q or W Q or W ZONE ZONE 1 2 9217G18A.DSF 9217G20A.DSF 9217G19A.
PAGE 3
Quik Bridge ® Two-Channel Receiver Sensor andTouchpad Compatibility The following current ITI Learn Mode™ wireless devices are compatible with this receiver: ■ Two- and Four-Button Keychain Touchpads ■ PIR motion sensors ■ Smoke sensors ■ Panic sensors (60-578 only) ■ Door/window sensors (see note below) Note: Only the internal reed switches of a door/window sensor can be used. The receiver does not support the use of door/window sensors with external devices connected to the sensor terminal block.
PAGE 4
Quik Bridge ® Two-Channel Receiver Overview of Receiver Operation LED Indicator The receiver has one LED. Table 1 lists the possible states of the LED and what they mean. PROGRAMMING BUTTON LED INDICATOR Table 1. What the states of the LED mean Power LED Means On and flickering irregularly Receiver has power and is functioning normally. Off Receiver has no power. Flashing regularly Receiver is ready to learn a wireless device.
PAGE 5
Quik Bridge ® Two-Channel Receiver Installation Guidelines Installation Observe the following guidelines when installing the receiver: ■ Leave ten inches above the receiver for the antenna. ■ Avoid areas that are likely to expose the receiver to moisture. ■ Avoid areas with excessive metal or electrical wiring, including furnace and utility rooms. ■ Avoid mounting the recevier on a metal surface.
PAGE 6
Quik Bridge ® Two-Channel Receiver receiver against the wall, mark the location of the top-left and lower-right mounting holes. Powering the Receiver SCREW MOUNTING HOLES CAUTION: You must be free of all static electricity when handling sensors. Touch a grounded metal object before handling the circuit board. You must connect the receiver to the 11 –15 VDC power outputs on the panel, or to a separate power supply (such as 12-volt DC adapter).
PAGE 7
Quik Bridge ® Two-Channel Receiver Zone Planning This section explains the capabilities, limitations, and suggested uses of the Quik Bridge Two-Channel Receiver. Possible Combinations of Wireless Devices Table 2. Each row shows a possible combination of wireless devices that you can program into the receiver. Zone 1 Zone 2 sensors sensors sensors Table 2 shows the combinations of wireless devices that you can program into the receiver. See Table 3 to find out what the Keychain Touchpad buttons do.
PAGE 8
PAGE 9
Quik Bridge ® Two-Channel Receiver Planning the installation Before you begin programming, it’s a good idea to write down how you plan to use the wireless devices with each zone. Use Table 5 as a worksheet. Table 5.
PAGE 10
Quik Bridge ® Two-Channel Receiver 5) 6) double-clicks indicates the number of wireless devices now added to the receiver. To add another wireless device into zone 1, go back to step 1 . If necessary, complete the installation of the device by adding it to the control panel (see the panel installation instructions). click from the receiver, which indicates that the receiver has successfully “learned” the key code.
PAGE 11
Quik Bridge ® Two-Channel Receiver Setting up Garage Door Opener Control ZONE 1 COMMON ZONE 1 N/O 1 +11–15 VDC GROUND The Quik Bridge Two-Channel Receiver is a super regenerative receiver. To ensure consistent operation of the receiver, mount it at least three feet away from other super regenerative receivers (such as the receiver in most garage door openers).
PAGE 12
Quik Bridge ® Two-Channel Receiver Testing Specifications This section explains how to test the operation of the wireless devices that you programmed into the Quik Bridge Two-Channel Receiver. Dimensions: 2.5 × 2.6 × 0.9'' (64 × 66 × 23 cm) General procedure for testing the Quik Bridge TwoChannel Receiver: Maximum current draw (both relays on): 70 m A Operating temperature range: 40 to 120°F (4 to 49°C) Power requirements: 11 to 15 VDC Receiver frequency: 319.
PAGE 13
Notices This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: 1) This may not cause harmful interference. 2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the user’s authority to operate the equipment.
PAGE 14
Quik Bridge ® Two-Channel Receiver Page 14