User guide

ManualsBrandsInterlogix ManualsSafetyT-500-PIV

U.S.

T 855 536 3573

F 561 998 6224

Asia

T 65 6424 7932

F 65 6424 7978

Australia

T 61 3 9239 1200

F 61 3 9239 1299

Canada

T 800 267 6317

F 613 737 5517

EMEA

T 48 58 326 22 40

F 48 58 326 22 41

Latin America

T 503 589 8614

F 561 994 6572

www.utcfireandsecurity.com

UTC Fire & Security, 9 Farm Springs Road,

Farmington, CT 06034-4065, USA

Transition Series

Multi-technology Access Readers

Description

Transition™ 500-PIV Series multi-technology card

readers feature simultaneous compatibility with multi-

vendor 125 kHz Proximity and PIV (ISO 14443A)

credential technologies—all in one reader. With this

remarkable technology combination, security

administrators can now deploy the Transition readers into

new or existing facilities.

Figure 1. Multi-technology Readers

Mounting the reader

All models of the T-500-PIV series readers can be

mounted using a U.S. single-gang electrical box or

directly to a wall.

1. Find a suitable mounting position on the door frame

or wall.

Note: For out of doors or wet locations, it is recommended

that the gasket provided be installed on the base as shown in

Figure 5.

2. If mounting directly to the wall, use one of the

following methods:

2a. Drill two vertical mounting holes from 3.25”

(83 cm) to 4.891” (125 cm) apart on the mounting

surface of the door frame or wall.

Figure 2. Direct wall mounting

2b. Models 520/525-PIV can be mounted using a

second pair of vertical mounting holes,

horizontally spaced 2.75” (70 cm) from the first

pair.

Figure 3. T520/525-PIV Direct wall mounting alternative

3. Drill one 0.625” (15.87 mm) diameter hole in wall for

the pigtail wire connection.

4. Follow the Cable Connection Chart to connect the

reader to the field panel and external door

equipment.

5. Mount the base plate to the wall using the supplied

screws.

6. Install gasket if required, see Figure 5.

Summary of content (3 pages)

PAGE 1
U.S. T 855 536 3573 F 561 998 6224 Asia T 65 6424 7932 F 65 6424 7978 Australia T 61 3 9239 1200 F 61 3 9239 1299 Transition Series Multi-technology Access Readers Canada T 800 267 6317 F 613 737 5517 EMEA T 48 58 326 22 40 F 48 58 326 22 41 Latin America T 503 589 8614 F 561 994 6572 www.utcfireandsecurity.com © 2012 UTC Fire & Security. All rights reserved. UTC Fire & Security, 9 Farm Springs Road, Farmington, CT 06034-4065, USA Description Figure 2.
PAGE 2
7. Install the top cover to the reader base. The base plate and top cover guides should be aligned, so the connectors seat correctly. Figure 4. Aligning base plate and top cover Connecting the cable 1. The readers are supplied with a 12-conductor cable pigtail with drain wire. Connect the pigtail to the host panel. Use the Cable Connection Chart (below) to correctly match the color of each wire. Color Signal Red 6 to 16 VDC Black Ground Green Data 0 White Data 1 Orange Green LED Control 8.
PAGE 3
Keypad configuration card Temperature rangea -31oF to +149oF (-35oC to +65oC) Cable distance to panel Up to 500 ft. (152.4 m) @ 12 VDC with 20 AWG shielded cable Read Rangeb (Distances may vary depending on environment.) Proximity Perfect and Ultralight cards are not supported by the Transition Series reader. Model T-500-PIV: - Proximity: up to 3.5" (8.89 cm) - HID Proximity: up to 3.5" (8.89 cm) - PIV: up to 1" (2.54 cm) Model T-520-PIV and T-525-PIV: - Proximity: up to 5" (15.