TruVision 360° Camera Bracket Installation Manual P/N 1072843A-EN • REV 1.
Copyright © 2014 United Technologies Corporation. Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Certification N4131 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Content Introduction 1 Bracket descriptions 2 TruVision 360° camera round back box (TVF-BBM) 2 TruVision 360° camera round angled back box (TVF-WBM) 2 TruVision 360° camera cup base back box (TVF-CBM) 3 TruVision dome swan neck bracket (TVD-SNB) 3 TruVision dome pendant mount bracket (TVD-PPB) 3 360° camera installation 4 To mount the 360° camera on a round back box 4 To mount the 360° camera on a round angled back box 5 To mount the 360° camera on a swan neck bracket 7 To mount the 360° camera on a pendant
Unpacking Please check the package contents to ensure that all parts are present and in good condition. Note: For safety purposes, the mounting surface must be able to support three times the combined weight of the bracket and camera. Bracket descriptions TruVision 360° camera round back box (TVF-BBM) Drywall anchor Φ7.5 x 24.5mm (4 pcs) Screw A Φ4 x 25mm (4 pcs) Screw B Φ4 x 10mm (3 pcs) Plug Inside view Outside view Side view TruVision 360° camera round angled back box (TVF-WBM) Drywall anchor Φ7.
TruVision 360° camera cup base back box (TVF-CBM) Screw B Φ4 x 10mm (3 pcs) TruVision dome swan neck bracket (TVD-SNB) Expansion screw Ø 10 mm (5 pcs) Locking screw Ø 4 mm (2 pcs) TruVision dome pendant mount bracket (TVD-PPB) Expansion screw Ø 10 mm (5 pcs) Locking screw Ø 4 mm (5 pcs) 1. Mounting plate TruVision 360° Camera Bracket Installation Manual 2.
360° camera installation To mount the 360° camera on a round back box 1. Using the three A screws and the drywall anchor, attach the back box to the wall. Note: The four other screw holes are for double gang. 2. Remove the camera cover from the camera. Open the small flap on the camera cover. Using the hex wrench provided, unscrew the hex head screw (1). Using a flathead screwdriver, release the two clips on the base of the camera (2) to detach the cover (3). 3. Connect the cables to the camera. 4.
Important: When mounting the camera to the back box, ensure that the ‘UP’ reference on the camera base is pointing upwards. 6. Re-attach the camera cover. 7. Tighten the cover screw in the camera cover to securely reattach cover to the camera. To mount the 360° camera on a round angled back box 1. Using the three A screws and the drywall anchor, attach the wedge back box to the wall. Note: The four other screw holes are for double gang. 2. Remove the camera cover from the camera.
3. Connect the cables to the camera. 4. Partially screw the three B screws into the wedge back box. 5. Attach the camera to the round angled back box. Align the holes on the base of the camera with the three back box screws and rotate the camera to lock it into position on the back box. Tighten the three B screws to securely fix the camera to the back box. Important: When mounting the camera to the back box, ensure that the ‘UP’ reference on the camera base is pointing upwards. 6.
To mount the 360° camera on a swan neck bracket 1. Pull the camera cables through the TVD-SNB bracket tube and then attach the swan neck bracket to the wall with the expansion screws (A) provided. 2. Screw the cup base onto the swan neck bracket and fasten with the locking screw, as shown (A). 3. Screw the three B screws into the cup base. 4. Remove the camera cover from the camera. Open the small flap on the camera cover. Using the hex wrench provided, unscrew the hex head screw (1).
6. Attach the camera to the cup base (A). 7. Re-attach the camera cover onto the camera (B). 8. Tighten the cover screw in the camera cover to securely reattach the cover to the camera. To mount the 360° camera on a pendant mount bracket 1. Screw the mounting plate onto the tube and fasten with the locking screw (A). 2. Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws. 3.
4. Partially screw the three B screws into the pendant bracket. 5. Connect the cables to the camera. 6. Remove the camera cover from the camera. Open the small flap on the camera cover. Using the hex wrench provided, unscrew the hex head screw (1). Using a flathead screwdriver, tighten the two clips on the base of the camera (2) to detach the cover (3). 7. Attach the camera to the cup base (A). 8. Re-attach the camera cover onto the camera (B).
9. Tighten the cover screw in the camera cover to securely reattach the cover to the camera. Specifications SKU Dimensions Weight TVD-SNB 253 × 95 × 180 mm 490 g (1.2 lb) TVD-PPB Ø 150 × 537 mm 1169 g (2.56 lb) TVF-BBM Ø 168 × 42 mm 337.5 g TVF-WBM Ø 168 × 49 mm 304.5 g TVF-CBM Ø 179 × 86 mm 542 g Pipe threading information Pipe thread size G1 10 Threads / in 11 Pitch (mm) 2.309 Thread major diameter Corresponding pipe Tapping drill size (mm) (mm) (in.) DN OD (mm) OD (in.
