TruVision 12/32 Series IP Camera Configuration Manual P/N 1072881-EN • REV B • ISS 08JAN15
Copyright Trademarks and patents Manufacturer © 2015 United Technologies Corporation. Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Building & Industrial Systems B.V.
Content Introduction 3 Network access 4 Checking your web browser security level 4 Accessing the camera over the internet 5 Overview of the camera web browser 5 Camera configuration 8 Configuration menu overview 8 Local configuration 9 System time 11 Network settings 12 Recording parameters 17 Video image 19 OSD (On Screen Display) 22 Overlay text 24 Privacy masks 24 Picture overlay 25 Motion detection alarms 26 Tamper-proof alarms 32 Exception alarms 33 Alarm inputs and outputs 34 Face detection 35 Audio e
Camera operation 61 Logging on and off 61 Live view mode 61 Playing back recorded video 61 Searching event logs 64 Operating PTZ control 66 2 TruVision 12/32 Series IP Camera Configuration Manual
Introduction This is the user manual for the following TruVision IP camera models: TVC-1201 (1.3MPX IP box camera, PAL) TVC-3201 (1.3MPX IP box camera, NTSC) TVC-1202 (3MPX IP box camera, PAL) TVC-3202 (3MPX IP box camera, NTSC) TVB-1201 (1.3MPX IP bullet camera, PAL) TVB-3201 (1.
Network access This manual explains how to configure the camera over the network with a web browser. TruVision IP cameras can be configured and controlled using Microsoft Internet Explorer (IE) and other browsers. The procedures described use Microsoft Internet Explorer (IE) web browser. Checking your web browser security level When using the web browser interface, you can install ActiveX controls to connect and view video using Internet Explorer.
To add the camera’s IP address to Internet Explorer’s list of trusted sites: 1. Open Internet Explorer. 2. Click Tools, and then Internet Options. 3. Click the Security tab, and then select the Trusted sites icon. 4. Click the Sites button. 5. Clear the “Require server verification (https:) for all sites in this zone box. 6. Enter the IP address in the “Add this website to the zone” field. 7. Click Add, and then click Close. 8. Click OK in the Internet Options dialog window. 9.
Figure 1: Web browser interface Table 1: Overview of the web browser interface Name Description 1. Live view Click to view live video. 2. Playback Click to play back video. 3. Log Click to search for event logs. There are three main types: Alarm, Exception and Operation. 4. Configuration Click to display the configuration window for setting up the camera. 5. Viewer View live video. Time, date and camera name are displayed here. 6. Current user Displays current user logged on. 7.
Name Description 13. Start/stop recording Click to record live video. 14. Digital zoom Click to enable digital zoom. 15. PTZ controls Direction actions, zoom, focus, iris, light and wiper control. Note: Direction actions, light, and wiper control can be used if the camera supports RS-485 and external pan/tilt unit, light or wiper is installed.
Camera configuration This chapter explains how to configure the cameras through a web browser. Once the camera hardware has been installed, configure the camera’s settings through the web browser. You must have administrator rights in order to configure the cameras over the internet. The camera web browser lets you configure the camera remotely using your PC. Web browser options may vary depending on camera model.
Configuration menus Description 2. Network Defines the network parameters required to access the camera over the internet. See “Network settings” on page 12 for further information on the setup. 3. Video/Audio Defines recording parameters. 4. Image Defines the image parameters, OSD settings, overlay text, and privacy mask. See “ To configure ROI settings: 1. From the menu toolbar, click Configuration > Video/Audio > ROI. 2. Select the desired channel from the drop-down list. 3.
Figure 3: Example of the Local configuration window Table 3: Overview of the Local configuration window Parameters Description Live View Parameters 1. Protocol Specifies the network protocol used. Options include: TCP, UDP, MULTICAST and HTTP. 2. Live View Performance Specifies the transmission speed. Options include: Shortest Delay or Auto. 3. Rules It refers to the rules on your local browser.
System time NTP (Network Time Protocol) is a protocol for synchronizing the clocks of network devices, such as IP cameras and computers. Connecting network devices to a dedicated NTP time server ensures that they are all synchronized. To define the system time and date: 1. From the menu toolbar, click Configuration > System > Time Settings. 2. From the Time Zone drop-down menu, select the time zone that is the closest to the camera’s location. 3.
Network settings Accessing the camera through a network requires that you define certain network settings. Use the “Network” menu to define the network settings. See Figure 4 and Table 4 below for further information. Figure 4: Network window (TCP/IP tab shown) Table 4: Network parameters Menu tabs Description 1. NIC Type: Enter the NIC type. Default is Auto. Other options include: 10M Half-dup, 10M Full-dup, 100M Half-dup and 100M Full-dup.
Menu tabs Description See page 14 for setup information. 2. Port HTTP Port: The HTTP port is used for remote internet browser access. Enter the port used for the Internet Explorer (IE) browser. Default value is 80. RTSP Port: RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. Enter the RTSP port value. The default port number is 554.
Menu tabs Description 11. A NAT (Network Address Translation) is used for network connection. Select the port mapping mode: auto or manual. See page 17 for setup information. NAT To define the TCP/IP parameters: 1. From the menu toolbar, click Configuration > Network > TCP/IP. 2. Configure the NIC settings, including the NIC Type, IPv4 settings, IPv6 settings, MTU settings, and Multicast Address. 3. If the DHCP server is available, check DHCP. 4.
To define the PPPoE parameters: 1. From the menu toolbar, click Configuration > Network > PPPoE. 2. Check Enable PPPoE to enable this feature. 3. Enter User Name, Password, and Confirm password for PPPoE access. 4. Click Save to save changes. To define the SNMP parameters: 1. From the menu toolbar, click Configuration > Network > SNMP. 2. Select the corresponding version of SNMP: v1, v2c or v3. 3. Configure the SNMP settings.
Directory: In the Directory Structure field, you can select the root directory, Main directory and Subdirectory. When the Main directory is selected, you have the option to use the Device Name, Device Number or Device IP for the name of the directory; and when the Subdirectory is selected, you can use the Camera Name or Camera No. as the name of the directory. Upload Type: To enable uploading the snapshots to the FTP server. 3. Click Save to save changes. To define the UPnP parameters: 1.
Attached Snapshot: Check the checkbox of Attached Snapshot if you want to send emails with attached alarm images. Interval: This is the time between two actions of sending attached images. Authentication: If your email server requires authentication, check this checkbox to use authentication to log in to this server. Enter the login user name and password. User Name: The user name to log in to the server where the images are uploaded. Password: Enter the password. Confirm: Confirm the password.
Figure 5: Video/Audio Settings menu (Video tab shown) Table 5: Video setting parameters Tab 1. Parameter descriptions Video Stream Type: Specifies the streaming method used. Options include: Main Stream (Normal), Sub Stream and Third stream. Video Type: Specifies the stream type you wish to record. Select Video Stream to record video stream only. Select Video&Audio to record both video and audio streams. Note: Video&Audio is only available for those camera models that support audio.
Tab Parameter descriptions Profile: Different profile indicates different tools and technologies used in compression. Options include: High Profile, Main Profile and Basic Profile. I Frame Interval: A video compression method. It is strongly recommended not to change the default value 50. 2. Audio Audio Encoding: G.722.1, G.711ulaw, G.711alaw, MP2L2 and G.726 are optional. Audio Input: “”Linein” and “MicIn” is selectable for the pickup or built-in microphone respectively.
Figure 6: Camera image settings menu – Display Settings tab Table 6: Image display parameters Parameter Description 1. Image Adjustment Brightness, Contrast Saturation, Sharpness Modifies the different elements of picture quality by adjusting the position of the values for each of parameter. 2. Exposure Settings Iris Mode There are two settings, Auto and Manual. The type of lens determines which setting is used. Default is Auto.
Parameter Description mode according to the configured time period. Triggered by Alarm Input: The camera switches to the day mode or the night mode after the alarm is triggered. Sensitivity If you choose Auto Day/Night switch, you can choose the sensitivity value from 0 to 7. The higher the value, the easier it is for the mode to switch. Default is 4. Filtering Time Only available when Auto D/N switch mode is selected. The filtering time refers to the interval time between the day/night switch.
Parameter Description Noise Reduction Level Only available when DNR is set to Normal Mode. Set the level of noise reduction in the Normal Mode. Higher value has a stronger noise reduction. Default is 50. Time/Space DNR Level Set the level of noise reduction level in Expert Mode. Default is 50. Note: If you set a higher value, the image may not be clear. Defog Mode You can enable the defog function when the environment is foggy and the image is misty.
To position the date/time and name on screen: 1. From the menu toolbar, click Configuration > Image (1) > OSD Settings (2). 2. Check the Display Name box (3) to display the camera’s name on screen. You can modify the default name in the text box of Camera Name. 3. Check the Display Date box (4) to display the date/time on screen. 4. Check the Display Week box (5) to include the day of the week in the on-screen display. 5. In the Camera Name box (6), enter the camera name. 6.
Overlay text You can add up to eight lines of text on screen. This option can be used, for example, to display emergency contact details. Each text line can be positioned anywhere on screen. See Figure 7 below. Figure 7: Text overlay menu To add on-screen text: 1. From the menu toolbar, click Configuration > Image > Text Overlay. 2. Check the box for the first line of text. 3. Enter the text in the text box. 4.
Figure 8: Camera image settings menu – Privacy mask window To add privacy mask area: 1. From the menu toolbar, click Configuration > Image > Privacy Mask. 2. Check the Enable Privacy Mask. 3. Click Draw Area. 4. Click and drag the mouse in the live video window to draw the mask area. Note: You are allowed to draw up to 4 areas on the same image. 5. Click Stop Drawing to finish drawing, or click Clear All to clear all of the areas you set without saving them. 6. Click Save to save changes.
Figure 9: Camera image settings menu To add a picture: 1. From the menu toolbar, click Configuration > Image > Picture Overlay. 2. Click Browse to select a picture and Upload to upload it. 3. Check Enable Picture Overlay checkbox to enable the function. Note: X Coordinate and Y coordinate values are for the location of the picture on the image. And the Picture width and height shows the size of the picture. Motion detection alarms You can define motion detection alarms.
Figure 10: Motion detection window Defining a motion detection alarm requires the following tasks: 1. Area settings: Define the on-screen area that can trigger a motion detection alarm and the detection sensitivity level (see Figure 10, item 1). 2. Arming schedule: Define the schedule during which the system detects motion (see Figure 10, item 2). 3. Recording schedule: Define the schedule during which motion detection can be recorded. See “Recording schedule” on page 50 for further information. 4.
as define the percentage of the motion detection area that the object must occupy, select day or night mode, and set up eight differently configured defined areas. To set up motion detection in normal mode: 1. From the menu toolbar, click Configuration > Events > Motion Detection. 2. Check the Enable Motion Detection box. Check Enable Dynamic Analysis for Motion if you want to see real-time motion events.
11. Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a motion detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information. If you want to send the event snapshot together with the email, check the Attached Snapshot option.
4. Under Switch Day and Night Settings, select OFF, Auto-switch or Scheduledswitch. Default is OFF. Auto-switch and Scheduled-switch allow you to set different settings for day and night as well as different periods. 5. Select Area No. and click Draw Area. Click and drag the mouse on the live video image to draw an area sensitive to motion detection. Note: You can draw up to eight motion detection areas on the same image. 6. Click Stop Drawing to finish drawing.
12. Choose the day and click schedule to other days. to set the detailed time period. You can copy the 13. Click OK to save changes. 14. Specify the linkage method when an event occurs. Check one or more response methods for the system when a motion detection alarm is triggered. Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a motion detection alarm.
Tamper-proof alarms You can configure the camera to trigger an alarm when the lens is covered and to take an alarm response action. Figure 11: Tamper-proof alarm window To set up tamper-proof alarms: 1. From the menu toolbar, click Configuration > Events > Tamper-proof. 2. Check the Enable Tamper-proof box. 3. Move the Sensitivity slider to set the sensitivity of the detection.
4. Click Edit to edit the arming schedule for tamper-proof alarms. The arming schedule configuration is the same as that for motion detection. See “To set up motion detection” for more information. 5. Specify the linkage method when an event occurs. Check one or more response methods for the system when a tamper-proof alarm is triggered. Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs.
3. Specify the linkage method when an event occurs. Check one or more response methods for the system when a tamper-proof alarm is triggered. Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is an exception alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information.
Upload Snapshot Capture the image when an alarm is triggered and upload the picture to NAS or FTP server. Note: To upload the snapshot to NAS, you must first configure the NAS settings. See “NAS settings” on page 48 for further information. To upload the snapshot to an FTP, you must first configure the FTP settings. See “To define the FTP parameters” on page 15 for further information. Enable the Upload Type option.
Figure 13: Face detection window To define face detection: 1. From the menu toolbar, click Configuration > Events > Face Detection. 2. Check Enable Face Detection to enable the function. 3. Check Enable Dynamic Analysis for Face Detection if you want the face detected to be marked with a green rectangle in live view. Note: If you do not want the detected face marked with the green frame, select Disable from Configuration > Local Configuration > Live View Parameters > Rules. 4.
Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a face detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information. If you want to send the event snapshot together with the email, check the Attached Snapshot option.
Figure 14: Audio exception detection window To define audio exception detection: 1. From the menu toolbar, click Configuration > Events > Audio Exception Detection. 2. Under Audio Input Exception, check Enable to activate the function. 3. Under Sudden Change of Sound Intensity check Enable to activate the function. 4. Configure the sensitivity and threshold. Sensitivity: The smaller the value, the larger the change should be to trigger the detection. The range is between 1 and 100.
Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a motion detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information. If you want to send the event snapshot together with the email, check the Attached Snapshot option. Trigger Channel Triggers the recording to start in the camera.
To define cross line detection: 1. From the menu toolbar, click Configuration > Events > Cross Line. 2. Check the Enable Cross Line Detection checkbox (1) to enable the function. 3. Click Draw Area (2), and a crossing plane will show on the image. 4. Click the line and two red squares appear at each end. Drag one of the red squares to define the arming area. Select the direction as A<->B, A ->B, or B->A from the drop down menu (3): A<->B: Only the arrow on the B side is displayed.
Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a cross line detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information. If you want to send the event snapshot together with the email, check the Attached Snapshot option.
Figure 15: Intrusion detection window To define intrusion detection: 1. From the menu toolbar, click Configuration > Events > Intrusion Detection. 2. Check the Enable Intrusion Detection checkbox to enable the function. 3. Click Draw Area, and then draw a rectangle on the image as the defense region. When you draw the rectangle, all lines should connect end-to-end to each other. Up to four areas are supported. Click Clear to clear the areas you have drawn.
Notify Alarm Recipient Send an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a motion detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 16 for further information. If you want to send the event snapshot together with the email, check the Attached Snapshot option.
Figure 16: Defocus detection window To define defocus detection: 1. From the menu toolbar, click Configuration > Events > Defocus Detection. 2. Check the Enable Defocus Detection checkbox to enable the function. Sensitivity: The range is between 1 and 100. The higher the sensitivity level, the smaller the defocus required to trigger an alarm. 3. Specify the linkage method when an event occurs. Check one or more response methods for the system when a defocus detection alarm is triggered.
Figure 17: Scene change detection window To define scene change detection: 1. From the menu toolbar, click Configuration > Events > Scene Change Detection. 2. Check the Enable Scene Change Detection checkbox to enable the function. 3. Configure the sensitivity ranging from 1 to 100, the higher the sensitivity, the easier the change of scene can trigger the alarm. 3. Click Edit to set the arming schedule for the alarm input. See “Motion detection alarms” on page 26 for more information. 4.
Notify Alarm Recipient Sends an exception or alarm signal to remote management software when an event occurs. Send Email Sends an email to a specified address when there is a scene change detection alarm. Note: You must configure email settings before enabling this option. See “To set up the email parameters” on page 17 for further information.
Figure 18: Snapshot menu To set up scheduled snapshots: 1. From the menu toolbar, click Configuration > Storage > Snapshot. 2. Check Enable Timing Snapshot to enable continuous snapshots. 3. Select the desired format of the snapshot, such as JPEG. 4. Select the desired resolution and quality of the snapshot. 5. Enter the time interval between two snapshots. Select the unit of time from the dropdown list: milliseconds, seconds, minutes, hour, or day. 6.
3. Select the desired format of the snapshot, such as JPEG. 4. Select the desired resolution and quality of the snapshot. 5. Enter the time interval between two snapshots. Select the unit of time from the dropdown list: milliseconds or seconds. 6. Under Capture Number, enter the total number of snapshots that can be taken. 7. Click Save to save changes. NAS settings You can use a network storage system (NAS) to remotely store recordings.
To set up a NAS system: 1. From the menu toolbar, click Configuration > Storage > NAS. 2. Enter the IP address of the network disk, and the NAS file path. 3. Click Save to save changes. Storage devices Use the storage management window to display the capacity, free space available, and the working status of the HDD of the NAS and the SD card in the camera. You can also format these storage devices. Before formatting the storage device, stop all recording.
Recording schedule You can define a recording schedule for the camera in the “Record Schedule” window. The recording is saved on to the SD card or NAS in the camera. The camera’s SD card provides a backup in case of network failure. The SD card is not provided with the camera. The selected recording schedule applies to all alarm types. Pre-record time The pre-record time is set to start recording before the scheduled time or event.
If you have selected “All day”, select one of the record types to record from the dropdown list box: • Continuous: This is continuous recording. • Motion detection: Video is recorded when the motion is detected. • Alarm: Video is recorded when the alarm is triggered via the external alarm input. • Motion | Alarm: Video is recorded when the external alarm is triggered or motion is detected. • Motion & Alarm: Video is recorded when motion and alarms are triggered at the same time.
To set up the RS-232 settings: 1. From the menu toolbar, click Configuration > System > RS232. 2. Select the RS-232 port parameters. Note: If you want to connect the camera using the RS-232 port, the RS-232 parameters must be the same as those configured here. 3. Click Save to save changes. RS-485 settings The RS-485 serial port is used to control the PTZ of the camera or connect to light and wiper devices. Configuration of these parameters should be done before you connect to any devices.
Camera management This chapter describes how to use the camera once it is installed and configured. The camera is accessed through a web browser. User management This section describes how to manage users. You can: Add or delete users Modify permission Modify passwords Only the administrator can manage users. The administrator can create up to 31 individual users for the cameras listed in this manual.
Operator: This user can only change the configuration of his/her own account. An operator cannot create or delete other users. Viewer: This user has the permission of live view, playback and log search. However, they cannot change any configuration settings. Add and delete users The administrator can create up to 31 users. Only the system administrator can create or delete users. To add a user: 1. From the menu toolbar, click Configuration > Security > User. 2. Select the Add button.
Basic Permissions Camera Configuration Remote: Video Output Control Remote: Serial Port Control 7. Click OK to save the settings. To delete a user: 1. Select the desired user under the User tab. 2. Click Delete button. A message box appears. Note: Only the administrator can delete a user. 3. Click Save to save the changes. Modify user information You can easily change the information about a user such as their name, password and permissions. To modify user information: 1.
To define RTSP authentication: 1. From the menu toolbar, click Configuration > Security > RTSP Authentication. 2. Select the Authentication type Enable or Disable in the drop-down list to enable or disable the RTSP authentication. 3. Click Save to save the changes. IP address filter This function allows you to give or deny access rights to defined IP addresses. For example, the camera is configured so that only the IP address of the server hosting the video management software is allowed to be accessed.
Defining the security service This function enables Telnet and let you define its password. It is only used by Technical Support. Figure 24: Security service window To define Telnet: 1. From the menu toolbar, click Configuration > Security > Security Service. 2. Check the checkbox of Enable Telnet. 3. Click Save to save the changes. Note: 1. The Telnet user name is root as default and cannot be changed. 2. The default Telnet password is “ab12!” 3.
4. Click OK in the pop-up message box to confirm restoring operation. Import/export a configuration file The administrator can export and import configuration settings from the camera. This is useful if you want to copy the configuration settings to camera, or if you want to make a backup of the settings. Note: Only the administrator can import/export configuration files. To import/export configuration file: 1. In Configuration > System, click the Maintenance tab to open its window. 2.
4. Click Update. You will receive a prompt asking you to reboot the camera. 5. When the upgrade is finished, the device will reboot automatically. The browser will also be refreshed. To upgrade the firmware via TruVision Device Manager: 1. In the FW upgrader panel, select a device or hold the Ctrl or Shift key to select multiple devices for simultaneous upgrading. 2. Click the browse button to locate the firmware file to use.
Reboot camera The camera can be easily rebooted remotely. To reboot the camera through the web browser: 1. In Configuration > System, click the Maintenance tab. 2. Click the Reboot button to reboot the device. 3. Click OK in the pop-up message box to confirm reboot operation.
Camera operation This chapter describes how to use the camera once it is installed and configured. Logging on and off You can easily log out of the camera browser window by clicking the Logout button on the menu toolbar. You will be asked each time to enter your user name and password when logging in. You can change the language of the interface from the drop-down menu in the top right corner of the window. Live view mode Once logged in, click “Live View” on the menu toolbar to access live view mode.
Figure 25: Playback window Name Description 1. Playback button Click to open the Playback window. 2. Search calendar Click the day required to search. 3. Search Start search. 4. Set playback time Input the time and click 5. Download functions to locate the playback point. Download video files. Download captured images. 6. Archive functions Click these buttons for the following archive actions: Enable digital zoom. Capture a snapshot image of the playback video.
Name Description 9. Timeline bar The timeline bar displays the 24-hour period of the day being played back. It moves left (oldest) to right (newest). The bar is color-coded to display the type of recording. Click a location on the timeline to move the cursor to where you want playback to start. The timeline can also be scrolled to earlier or later periods for play back. Click to zoom out/in the timeline bar. 10. Audio control Control level of audio. 11.
To archive recorded snapshots: 1. Click to open the snapshots search window. 2. Select the snapshot type as well as the start and end time. 3. Click Search to search for the snapshots. 4. Select the desired snapshots, and click Download to download them. Searching event logs You must configure NAS or insert a SD card in the dome camera to be able to use the log functions. The number of event logs that can be stored on NAS or SD card depends on the capacity of the storage devices.
Figure 26: Log window 1. Major Type 4. Start search 2. Minor Type 5. Save searched logs 3. Start and end search time You can search for recorded logs by the following criteria: Major type: There are four types of logs: All Types, Alarm, Exception, and Operation. See Table 7 below for their descriptions. Minor type: Each major type log has some minor types. See Table 7 below for their descriptions. Date and Time: Logs can be searched by start and end recording time.
Main log type Minor log types: Description of events included Operation Power On, Abnormal Shutdown, Remote Reboot, Remote Login, Remote Logout, Remote Configure parameters, Remote Start Record, Remote Stop Record, Remote PTZ Control, Remote Initialize HDD, Remote Playback by File, Remote Playback by Time, Remote Export Config file, Remote import config file, Remote Get Parameters, Remote Get Working Status, Establish Transparent Channel, Disconnect Transparent Channel, Start Bidirectional Audio, Stop Bi
Description 7. Initializes the lens Note: 1. To do pan/tilt movement using the direction buttons, the camera connected to the network must support RS-485 and a pan/tilt unit must be installed in the camera. Please properly set the PTZ parameters on RS-485 Settings page referring to Defining RS-485 settings 2. To control the lens, such as zoom or focus, the camera must support auto focus. To set a preset: 1. Select a preset number from the preset list. 2.
To set a preset tour: 1. In the PTZ control panel, click to enter the tour settings interface. 2. Select a preset tour number from the drop-down list. 3. Click to enter the adding interface of preset. 4. Configure the preset number, preset tour time and preset tour speed. Preset Tour Duration: The dwell time. The length of time in seconds for which a camera stays at a preset before moving to the next preset. Preset Tour Speed: The speed the camera moves from one preset to another. 5.
Index A Alarm inputs set up, 34 Alarm outputs set up, 34 Alarm types motion detection, 26 Archive files recorded files, 63 snapshots of recorded files, 63 Archived files play back, 63 Archivefiles set up default directories, 8 Archiving files set up default directories, 9 Audio parameters, 17 Email parameters set up, 16 Events searching logs, 64 Exception alarms types, 33 F Firmware upgrade, 58 H HDD capacity, 49 formatting, 49 HDD error alarm, 33 HDD full alarm, 33 C I Camera image configuring, 19 Ca
P Passwords modify, 55 Picture overlay, 25 Playback play back recorded files, 63 screen, 61 search recorded video, 61 Port parameters set up, 14 Post-recording times description, 50 Pre-recording times description, 50 Privacy masks, 24 PTZ control, 66 R Reboot camera, 60 Recording manual recording, 61 parameters, 17 playback, 61 recoding schedule, 50 snapshots in live view mode, 61 RS-232 settings, 51 RS-485 settings, 52 RTSP authentification, 55 S SDHC card capacity, 49 formatting, 49 Snapshot, 46 Snapsh
