TruVision High Definition TVI Bullet Camera Installation Guide TVB-2401, TVB-4401 TVB-2403, TVB-4403 P/N 1072936-EN • REV A • ISS 12MAR15
Contents Product overview 1 Camera description 3 Installation 5 Programming 7 Setup menu 9 Specifications 10 Legal and regulatory information 11 Product overview This is the Installation Guide for TruVision High Definition TVI Bullet Camera TVB-2401/TVB-4401 and TVB-2403/TVB-4403. This guide describes a standard installation.
Package contents: Camera with power and video output cables 3 screws and 3 anchors for wall or ceiling installation Template Installation Guide • WEEE and Battery Disposal CD 2 Installation Guide
Camera description TVB-2401/TVB-4401 1 3 4 2 5 6 1. 2. 3. TVI video output cable (grey) Power cable Mounting base output Installation Guide 4. 5. 6.
TVB-2403/TVB-4403 1 2 5 3 4 6 7 8 1. 2. 3. 4. WDR/CVBS switch cable Power cable TVI video output cable (grey) CVBS video output cable (black) 5. 6. 7. 8. Mounting base Sun shield Lens IR LED Note: Please check the camera output settings before setting up a system. The TVI video output can be only connected to a DVR with TVI signal input. The CVBS output supports the standard monitor, test monitor, encoder and DVR.
For TVB-2403/TVB-4403, you can connect the white and black line ends of the WDR switch cable to enable the Wide Dynamic Range (WDR) function. The WDR function is disabled by default. If WDR is enabled, the CVBS output will be blocked out, and only TVI output is available. Installation To install the camera on a ceiling: 1. Using the template, place it level against the mounting surface and mark the position of the mounting holes. Drill Template 2.
4. Using a 75-ohm coaxial video cable, connect the camera TVI video output and a TVI DVR, and connect a 12 VDC power supply to the camera power cable. 5. Adjust the camera position and angle as required.
Programming Programming on TVI output: Programming on TVI output is available for TVB2403/TVB-4403 only. Once the camera hardware has been installed, you can configure the camera settings on the TVI DVR. TVI Select PTZ protocol as TruVision Coax and click menu button to call up the camera menu. For more details, please see the TVI DVR user manual.
Programming on CVBS output: Programming on CVBS output is available for TVB2403/TVB-4403 only. Programming on CVBS output, you need to connect a monitor and a TVS-C200 controller (purchase separately) as following system figure. TVI CVBS The TVS-C200 has one male BNC output and a female output. Please connect the male output to camera’s CVBS output and female output to a monitor.
Setup menu Installation Guide 9
Specifications Power supply 12 VDC Current TVB-2401/TVB-4401: Max.300mA TVB-2403/TVB-4403: Max. 330mA Power consumption TVB-2401/TVB-4401: Max. 3.5 W TVB-2403/TVB-4403: Max.4 W Weight TVB-2401/TVB-4401: 0.64 lb. (291 g) TVB-2403/TVB-4403: 0.68 lb. (309 g) Dimensions (Ø × L) 2.76 x 5.89 in. (70 x 149.
Legal and regulatory information Copyright: © 2015 United Technologies Corporation, Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents: Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Canada This Class A digital apparatus complies with Canadian ICES-003.
