TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual P/N 1072543B-EN • ISS 21JUN12
Copyright Trademarks and patents © 2012 UTC Fire & Security. All rights reserved. The TruVision and Interlogix names and logo are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Manufacturer UTC Fire & Security Americas Corporation, Inc. 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
Content Product overview 2 Package Contents 2 Features 2 User guidelines 2 Product description 3 Installation 4 Attach the lens 4 Connect the cables 4 Programming 6 OSD control button 6 Access the Setup menu 6 Save changes 7 Select the lens type 7 Set shutter/AGC 8 Set white balance 9 Set backlight compensation (BLC) 10 Adjust the picture characteristics 10 Set ATR level 11 Set motion detection 11 Set the privacy mask area 12 Set Day/Night mode 13 Set image noise reduction 13 Set the camera ID 14 Set sync m
Product overview The TVC-6110-1-N(-P)/ TVC-6120-1-N(-P) camera uses a digital signal processor (DSP) to process video signals. The camera includes a microcontroller to provide high-quality images with high-color reproduction and sharp pictures.
WARNING: To reduce the risk of fire or electronic shock, do not expose the camera to rain or moisture and do not remove the cover or back. Product description Figure 1: Product description - TVC-6110-1-N(-P) 1. OSD control button 2. Power LED 3. 12 VDC Power 4. Video output 5. Ground Figure 2: Product description – TVC-6120-1-N(-P) 1 2 3 4 5 8 7 1. 2. 3. 4. OSD control button Alarm output/Ground D/N switch (3.3V) RS-485 ports (D+, D-) TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual 6 5. 6.
Installation Please check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. To install the camera you will need to prepare the mounting surface, mount the camera, attach the lens, and make cable connections. Note: Before installing, please ensure that the mounting surface is strong enough to withstand three times the weight of the camera. If the mounting surface is not strong enough, the camera may fall and cause serious damage.
Power supply Monitor Note: TVC-6110-1-N(-P) is 12 VDC only.
Programming Once the camera hardware has been installed, the camera can then be configured. Program the camera by attaching a standard video monitor to the system. To connect the monitor: 1. Plug the monitor output cable to the video monitor output connector. 2. Connect the BNC cable to the video monitor. 3. Press Enter on the OSD menu button to display the Setup menu. See Table 1 for instructions on how to move the cursor.
Table 2: Setup menu description Menu item Description Lens Defines autoiris or manual iris. Shutter/AGC Define the method of iris control, shutter and AGC. White Bal Defines the white balance (WB) set up. Backlight Defines the highlight compensation (HLC) and backlight compensation (BLC) set up. Pict Adjust Defines the image quality functions. ATR Defines the adaptive tone reproduction (ATR) set up. Motion Det Defines the motion detection set up. Privacy Defines privacy mask set up.
Manual menu: Select a higher shutter speed value to see movement and a lower value to see clearer images. The shutter speed available are 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000 and 1/10000. The AGC value can be set between 6 and 44.8. Auto iris menu: Type: Select the drive mode of the lens, DC or Video. Mode: Select the iris control mode. Auto (automatically controlled depending on the light), Open (always open), or Closed (always closed).
Low luminance: Sets the lux level for low light conditions. Mode: Only AGC is available. Brightness: Adjust the brightness to X0.25, X0.50, X0.75 or X1. Manual shutter menu: Mode: Only Shut/AGC available. Shutter: Set the manual shutter to 1/60(1/50), 1/100(1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000 or 1/10000. AGC: Set the gain level. A higher gain compensates for a brighter scene but noise increases. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8 dB.
Menu Item Description has no limits between 1,800 to 10,500˚K so it may over-compensate the WB for a large single-color object. User1 This is a fixed white balance that is user-defined by blue and red gain parameters. Only use this function when there is steady light. Blue-gain from 0 to 255 Red- gain from 0 to 255 User2 This is a second fixed white balance that is user-defined by blue and red gain parameters. Only use this function when there is steady light.
Set the camera image characteristics such as brightness, contrast, sharpness, hue, and saturation (called “Gain” here) of the picture. The parameters of each can be set between 0 and 255. Use the mirror function to flip the camera image so that it is correctly orientated for viewing. The image can be flipped vertically, horizontally or horizontallyvertically (180 degrees). Default setting is Off. Set ATR level This feature is similar to WDR (wide dynamic range).
Detect sense: Set the sensitivity level for motion detection. A higher value is more sensitive. Block Disp: When enabled, any movement detected will be tracked on-screen. Press Enter to enable or press the button again to cancel it. Monitor area: When enabled, a square grid is displayed on-screen. It can only be enabled if Block Disp is also enabled. Area Sel: Up to four motion-sensitive areas can be set. Set the size and position of each one.
Set Day/Night mode In the Setup menu, go to Day/Night and select the desired mode. The Day/Night mode has two options: Auto, Color and B/W. Select Color to manually set the camera to color (day) mode. Select Auto so that the camera can automatically switch between day (color) and night (black and white) mode. Auto mode: Burst: Enable/disable the color burst component of the video signal when the camera switches to B/W.
Set the camera ID In the Setup menu, go to Camera ID and press Enter to display the menu. The camera ID displayed on-screen can have up to 40 characters. Camera ID input line Command line To enter a character, move the cursor to the desired character and press Enter to select it. It appears in the input line. Repeat the process until all characters are entered. To move the character input position in the input line, move the cursor in the command line to ← or → and press Enter.
Select the language Use this menu to select the OSD language. In the Setup menu, go to Language and select the desired language. There are only two languages available, English and Japanese. Reset camera settings Use this menu to reset the camera settings to factory default. In the Setup menu, go to Camera Reset and press Enter.
Specifications Model TVC-6110-1-N(P) Pickup device TVC-6120-1-N(P) 1/3" Super HAD CCD II Total pixels NTSC: 811 × 508 / PAL: 795 × 596 Effective pixels NTSC: 768 × 494 / PAL: 752 × 582 Resolution Synchronization system 600 TVL Internal Internal / Line up Scanning system IR cut 2:1interlace NA Yes S/N ratio 52 dB (AGC Off) Electronic shutter PAL: 1/50 to 1/10,000 s NTSC: 1/60 to 1/10,000 s Minimum illumination Video output White balance 0.01 lux (F1.
Menu Map TruVision TVC-6110-1 / TVC-6120-1 Camera User Manual 17
