TruVision TVC-7120-1 Camera User Manual P/N 1072793A • REV 1.
Copyright Trademarks and patents Manufacturer Certification FCC compliance Canada © 2014 United Technologies Corporation. Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Content Product overview 2 Package contents 2 Features 2 User guidelines 2 Product description 3 Installation 4 Attach the lens 4 Connect the cables 4 Programming 6 OSD control button 6 Access the Setup Menu 6 Save changes 7 Select the lens type 7 Set the shutter/AGC 8 Set white balance 9 Set backlight compensation (BLC) 10 Adjust the picture characteristics 11 Set the ATR level 11 Set the motion detection 11 Set the privacy mask area 12 Set the Day/Night mode 13 Set image noise reduction 14 Set the camera
Product overview The TVC-7110-1-N(-P) / TVC-7120-1-N(-P) camera uses a digital signal processor (DSP) to process video signals. The camera includes a microcontroller to provide high-quality images with high-color reproduction and sharp pictures.
WARNING: To reduce the risk of fire or electronic shock, do not expose the camera to rain or moisture and do not remove the cover or back. Product description Figure 1: Product description - TVC-7120-1-N(-P) 1. 2. 3. 4. OSD control button Alarm output/Ground D/N switch (3.3 V) RS-485 ports (D+, D-) TruVision TVC-7120-1 Camera User Manual 5. 6. 7. 8.
Installation Please check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. To install the camera you will need to prepare the mounting surface, mount the camera, attach the lens, and make cable connections. Note: Before installing, please ensure that the mounting surface is strong enough to withstand three times the weight of the camera. If the mounting surface is not strong enough, the camera may fall and cause serious damage.
Power supply Monitor TruVision TVC-7120-1 Camera User Manual 5
Programming Once the camera hardware has been installed, the camera can then be configured. Program the camera by attaching a standard video monitor to the system. To connect the monitor: 1. Plug the monitor output cable to the video monitor output connector. 2. Connect the BNC cable to the video monitor. 3. Press Enter on the OSD menu button to display the Setup Menu. See Table 1 for instructions on how to move the cursor.
Table 2: Setup Menu description Menu item Description Lens Defines autoiris or manual iris. Shutter/AGC Define the method of light control. White Bal Defines the white balance (WB) set up. Backlight Defines the highlight compensation (HLC) and backlight compensation (BLC) set up. Pict Adjust Defines the image quality functions. ATR Defines the adaptive tone reproduction (ATR) set up. Motion Det Defines the motion detection set up. Privacy Defines privacy mask set up.
Manual menu: Select a higher shutter speed value to see movement and a lower value to see clearer images. The shutter speed available are 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000 and 1/10000. The AGC value can be set between 6 and 44.8. Auto iris menu: Type: Select the drive mode of the lens, DC or Video. Mode: Select the iris control mode. Auto (automatically controlled depending on the light), Open (always open), or Closed (always closed).
Brightness: Select the brightness level to which the iris and shutter speed will adjust automatically. The value ranges from 0 to 255. Low Luminance: Sets the lux level for low light conditions. Mode: Only AGC is available. Brightness: Adjust the brightness to X0.25, X0.50, X0.75 or X1. Manual shutter menu: Mode: Only Shut/AGC available. Shutter: Set the manual shutter to 1/60(1/50), 1/100(1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000 or 1/10000. AGC: Set the gain level.
Menu Item Description compensated for high color temperature such as from daylight). Default is Indoor. Push Like ATW, the Push function continually monitors/analyzes the color temperature of the incoming light and corrects the WB. However, Push has no limits between 1,800 to 10,500˚K so it may over-compensate the WB for a large single-color object. User1 This is a fixed white balance that is user-defined by blue and red gain parameters. Only use this function when there is steady light.
Adjust the picture characteristics In the Setup Menu, go to Pict Adjust and select the options to be modified. Set the camera image characteristics such as brightness, contrast, sharpness, hue, and saturation (called “Gain” here) of the picture. The parameters of each can be set between 0 and 255. Use the mirror function to flip the camera image horizontally so that it is correctly orientated for viewing. Default setting is Off. Set the ATR level This feature is similar to WDR (Wide Dynamic Range).
In the Setup Menu, go to Motion Det and select the desired parameters. Default setting is Off. Detect Sense: Set the sensitivity level for motion detection. A higher value is more sensitive. Block Disp: When enabled, any movement detected will be tracked onscreen. Press Enter to enable or press the button again to cancel it. Monitor Area: When enabled, a square grid is displayed on-screen. It can only be enabled if Block Disp is also enabled. Area Sel: Up to four motion-sensitive areas can be set.
Set the Day/Night mode In the Setup Menu, go to Day/Night and select the desired mode. The Day/Night mode has four options: Auto, Color, B/W, and EXT1/EXT2. Select Color to manually set the camera to color (day) mode. Select Auto so that the camera can automatically switch between day (color) and night (black and white) mode. Auto mode: Burst: Enable/disable the color burst component of the video signal when the camera switches to B/W.
On the B/W submenu, you can switch it to ON or OFF to enable or disable BURST. EXT1/EXT2 mode: EXIT1/EXT2 mode enables synchronization of day/night and IR light. Note: EXIT1/EXT2 mode is only available for TVC-7120-1. Set image noise reduction In the Setup Menu, go to NR and select the desired mode. Set the noise reduction strength of the luminance signal (Y). Set the camera ID In the Setup Menu, go to Camera ID and press Enter to display the menu.
To delete a character in the input line, select the character so that it blinks. Then move the cursor to CLR on the command line and press Enter. To position the camera ID on-screen, move the cursor to POS and press Enter. The menu will then disappear on-screen and the camera ID will be displayed on the monitor. Use the menu button to move the camera ID to the desired position. Press Enter. The menu will reappear. Select Return to return to the previous menu.
Specifications Model TVC-7120-1-N(P) Pickup device 1/3" Super HAD CCD II Total pixels (H NTSC: 1028 × 508 / PAL: 1028 × 596 Effective pixels NTSC: 976 × 494 / PAL: 976 × 582 Resolution 700 TVL Synchronization system Internal / Line lock Scanning system 2:1interlace WDR DWDR IR cut Yes S/N ratio 62 dB (AGC Off) Electronic shutter NTSC: 1/60 to 1/10,000 s PAL: 1/50 to 1/10,000 s Minimum illumination 0.001 Lux @ (F1.
Menu Tree TruVision TVC-7120-1 Camera User Manual 17
