TruVision Series 4 IP Camera Installation Guide P/N 1073195-EN • REV D • ISS 24AUG16
Copyright © 2016 United Technologies Corporation, Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Manufacturer Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
interference. (2) This Device must accept any interference received, including interference that may cause undesired operation. ACMA compliance Canada Notice! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This Class A digital apparatus complies with CAN ICES-003 (A)/NMB-3 (A). Cet appareil numérique de la classe A est conforme à la norme CAN ICES-003 (A)/NMB-3 (A).
information see: www.recyclethis.info. Contact information For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.
Content Introduction 2 Product overview 2 Installation 3 Installation environment 3 Package contents 4 Cable requirements 10 Camera description 11 Setting up the camera 15 IR illuminators 16 Accessing the SD card 17 Mounting the bullet camera 17 Mounting the VF mini dome camera 18 Mounting the outdoor dome camera 24 Using the camera with a TruVision recorder or another system 29 Using the camera with TruVision Navigator 29 Specifications 29 TruVision IP box cameras 29 TruVision IP VF bullet dome 30 TruVisio
Introduction Product overview This is the installation guide for TruVision Series 4 IP camera models: TVC-5401 (2MPX IP box camera) TVC-5402 (3MPX IP box camera) TVC-5403 (5MPX IP box camera) TVB-5401 (2MPX IP bullet camera, 2.8 to 12 mm) TVB-5402 (2MPX IP bullet camera, 8 to 32 mm) TVB-5403 (3MPX IP bullet camera, 2.8 to 12 mm) TVB-5404 (3MPX IP bullet camera, 8 to 32 mm) TVB-5405 (5MPX IP bullet camera, 2.8 to 12 mm) TVD-5401 (2MPX IP VF mini dome, 2.
Installation This section provides information on how to install the cameras. Installation environment When installing your product, consider these factors: • Electrical: Install electrical wiring carefully. It should be done by qualified service personnel. Always use a proper PoE switch or a 12 VDC UL listed Class 2 or CE certified power supply to power the camera. Do not overload the power cord or adapter.
• Cleaning: Do not touch the sensor modules with fingers. If cleaning is necessary, use a clean cloth with some ethanol and wipe the camera gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensors from dirt. Package contents Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit; contact the supplier immediately.
• WEEE and Battery Disposal sheets IP VF bullet camera • Camera • Back box • Template • Screws M4.
• Screws (4 pcs) • Water joint: Provide water resistance to network connection.
IP VF mini dome camera • Camera • Adaptor: for TVD-CB3 cup base • Template • Screws (4 pcs) • Hex wrench • CD with Configuration manual and TruVision Device Manager Installation Guide 7
• Installation manual • WEEE and Battery Disposal sheets IP VF outdoor dome camera • Camera • Back box • Template (flush mount) • Template (back box) • Screws: 4 × 75 mm (3 pcs) Drill Template • 8 Screws (4 pcs) Installation Guide
• Screws M4 × 9.5 (3 pcs) to attach the back box • Wrench • Alarm connector (4 pcs) • Water joint: Provide water resistance to network connection.
CAUTION: Use direct plug-in UL listed power supplies marked Class 2/CE certified or LPS (limited power source) of the required output rating as listed on the unit. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Cable requirements For proper operation, adhere to the following cable and power requirements for the cameras. Category 5 cabling or better is recommended.
Camera description Figure 1: IP bullet camera GND AUX 1. Ethernet RJ45 PoE port 2. Power supply 3. Reset button 4. SD card slot 5. BNC port 6. Ground 7. Alarm Out Installation Guide 8. Aux Power Port (AUX&GND) 9. RS-485 port 10. Alarm In 11. Audio Out 12. ABF (automatic back focus) button 13.
Note: 1. To reset the camera to default settings, press and hold the RESET button and power on the camera. After the camera is started up, please hold the Reset button for an additional 20 seconds. 2. The type of auto-iris interface is shown below: No. DC-driven 1 Damp- 2 Damp+ 3 Drive+ 4 Drive- Power, Video and GND pins are used when the auto-iris is driven by video. Damp+, Damp-, Drive+ and Drivepins are used when the auto-iris is driven by DC.
Figure 2: IP VF bullet camera 1. Light sensor 8. Power supply 2. Lens 9. Alarm I/O 3. Shield 10. Audio output 4. Mounting base 11. Audio input 5. DC 12V output 12. 6. BNC output 13. SD card slot 7. Ethernet RJ45 PoE port 14.
Figure 3: IP VF mini dome camera 1. Dome liner 7. Serial port 2. Bubble Assembly 8. SD card slot 3. Lens 9. Adaptor 4. BNC port 10. Knockout 5. Reset button 11. Camera terminals 6.
Figure 4: IP VF outdoor dome camera 1. Dome liner 7. Power supply 2. Bubble Assembly 8. Lens 3. SD card slot 9. 4. Video output Alarm I/O, 12 V AUX output and Audio I/O 5. Reset button 6. Ethernet RJ45 PoE port 10. BNC output 11. Back box Setting up the camera Note: If the light source where the camera is installed experiences rapid, wide-variations in lighting, the camera may not operate as intended.
To quickly put the camera into operation: 1. Prepare the mounting surface. 2 Mount the camera on the mounting surface using the appropriate fasteners. See “Mounting the bullet camera” on page 17. 3. Set up the camera’s network and streaming parameters so that the camera can be controlled over the network. For further information, please refer to the “TruVision Series 4 IP Camera Configuration Manual”. 4. Program the camera as appropriate for its location.
Accessing the SD card Insert a Micro SD card with up to 128GB to use the camera as an additional recording device, or as a backup in case of failure of communication with the network video recorder (see Figure 1 on page 11). The card is not supplied with the camera. For the IP VF mini dome and outdoor dome cameras, point the lens vertically upwards to access the SD card slot. Recorded video and log files can be accessed via the web browser or via TruVision Navigator.
3. Hook the camera to the back box with the safety cable. Use the screws to fix the camera to the back box. Mounting the VF mini dome camera To mount the VF dome camera on a ceiling or wall: 1. Loosen the three screws on the edge of the lower dome with a wrench. 2. Open the lower dome and remove the black inner liner.
3. Using the drill template, drill the holes in the mounting surface. Screw holes Cable holes 4. If you want to route the cables behind the dome, drill a cable hole in the ceiling or wall using the drill template.
supported. Use a pliers to remove the knockout plug shown in the figure below, and route the cables from the knockout. Knockout 5. Fix the adapter plate to the ceiling with the supplied screws. 6. Align the mounting base with the adapter plate and route the mounting base counterclockwise to fit it to the adapter plate. Then secure it by tightening the lock screw.
Lock screw 7. 8. Adjust the viewing angle according to the figure below. Panning angle [0~80°], tilting angle [0~355°], and azimuth angle of the lens [0~355°]. Adjust the focus and zoom. a) Connect the VIDEO OUT interface of the camera to the event monitor. b) Set the iris type to MANUAL.
c) Adjust the No.1 Zoom Lever (T~W) to select a proper angle of view. d) Adjust the No.2 Focus Lever (F~N) to obtain the desired image quality on the monitor. e) Set the iris type as MANUAL if the environment has a good and stable illumination. Set the iris type as AUTO if the environment has varied levels of illumination. 2 9. 1 Attach the black liner to the dome drive. 10. Attach the bubble to the dome drive and rotate it to tighten.
Dome drive Black liner Bubble 11. Tighten the lock screw to complete the installation.
Mounting the outdoor dome camera To mount the outdoor dome camera on a ceiling: 1. Drill the screw holes on the ceiling with the supplied drilling template. To route the cables from the base of the camera, cut a cable hole in the ceiling. 2. Install the mounting base to the ceiling with the supplied screws. 3. Connect the corresponding power cable and network cables. 4. Remove the bubble and liner of the camera.
5. 6. Install the dome camera to the mounting base. Adjust the viewing angle. a) Loosen the lock screw beside the lens. b) Hold the plastic plate and rotate the camera to adjust the panning angle [0~350°]. c) Push the lens forward and backward to adjust the tilting angle [0~80°].
d) Rotate the lens to adjust the azimuth angle of the camera [0~350°]. e) Tighten the lock screw. Tilt 80° Pan 350° Rotation 350° 7. Re-attach the dome liner and bubble to the camera. To mount the outdoor dome camera into a ceiling: 1. 26 Drill the screw holes on the ceiling with the supplied drilling template.
Drill Template 2. Remove the housing and liner from the camera. 3. Secure the camera to the holes with three screws.
4. 28 Re-attach the housing and liner.
Using the camera with a TruVision recorder or another system Please refer to the NVR/DVR user manuals for instructions on connecting and operating the camera with these systems. Using the camera with TruVision Navigator A camera can either be connected to a TruVision, or it can be added directly to TruVision Navigator. Please refer to the TruVision Navigator user manual for instructions on operating the camera with TruVision Navigator.
TruVision IP VF bullet dome Electrical Voltage input 12 VDC, PoE+ (IEEE 802.3at) Power consumption Max. 13 W Miscellaneous Connectors Audio In/Out, Alarm In/Out, 12 VDC Power Input, Network Port (PoE), CVBS Output, AUX Power Output Operating temperature -40 to +60 °C (-40 to +140 °F) Dimensions Ø 115.8 × 291.8 mm (Ø 4.56 × 11.5 in.) Weight 1600 g Environmental rating IP66 TruVision IP VF mini cameras Electrical Voltage input 12 VDC, PoE (IEEE 802.3af) Power consumption 2MPX: Max. 7.
Dimensions Ø 140 × 121.8 mm Weight 1400 g (3.09 lbs.) Environmental rating IK10 (Ø 5.51 × 4.80 in.) TruVision IP VF outdoor dome cameras Electrical Voltage input 12 VDC/24 VAC, PoE+ (IEEE 802.3at) Power consumption Max. 17 W Miscellaneous Connectors Network Port(PoE), 12 VDC/24 VAC Power Input, Aux Power Output, Audio In/Out, Alarm In/Out, CVBS Output. Operating temperature -40 to +60°C (-40 to +140°F), with heater on Dimensions Ø 159.8 × 146 mm (Ø 6.29 × 5.75 in.) Weight 2100 g (4.62 lbs.
Pin definitions There are eight wires on a standard UTP/STP cable and each wire is color-coded.
Please make sure your connected cables have the same pin assignment and color as above before deploying the cables in your network.