TruVision HD-TVI 3MPX Camera Configuration Manual P/N 1073217-EN • REV B • ISS 19JAN17
Copyright © 2017 United Technologies Corporation. All rights reserved. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. Trademarks and patents The TruVision and Interlogix names and logos are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Content Introduction 2 HD-TVI 3MPX IR Bullet Cameras 2 HD-TVI 3MPX IR Turret Cameras 2 Programming 3 Call up the camera OSD menu 3 Menu trees 5 TVB-2407/4407 (fixed lens bullet) and TVT-2401/4401 (fixed lens turret) cameras 5 TVB-2408/4408 (motorized VF lens bullet) and TVT-2402/4402 (motorized VF lens turret) cameras 5 Configuration 6 FORMAT 6 FOCUS 6 MAIN MENU 6 AE (Auto Exposure) 6 WB (White Balance) 7 DAY/NIGHT 7 VIDEO SETTING 8 RESET 9 SAVE & EXIT 9 Preventing IR reflection 9 TruVision HD-TVI 3MPX Cam
Introduction This is the configuration manual for following camera models: HD-TVI 3MPX IR Bullet Cameras TVB-2407 (3MPX TVI Bullet Camera, Fixed Lens, IR, PAL) TVB-4407 (3MPX TVI Bullet Camera, Fixed Lens, IR, NTSC) TVB-2408 (3MPX TVI Bullet Camera, VF Motorized Lens, IR, PAL) TVB-4408 (3MPX TVI Bullet Camera, VF Motorized Lens, IR, NTSC) HD-TVI 3MPX IR Turret Cameras TVT-2401 (3MPX TVI Turret Camera, Fixed Lens, IR, PAL) TVT-4401 (3MPX TVI Turret Camera, Fixed Lens, IR, NTSC)
Programming Once the camera hardware has been installed, the camera can be configured using the built-in OSD button (if supported) and the TVI DVR menu. The TVSC200 controller (Service Tool) does not support the 3MPX cameras. You can also configure the camera settings via a TVI DVR. Select the PTZ protocol TruVision Coax and click the menu button to call up the menu. When using the TVI output, the 3MPX TVI cameras must be used with the higher resolution (3MPX or higher) TVI DVRs.
7. When the setup is complete, select Exit and click Iris+ to exit the camera OSD. Note: You cannot exit the camera setup menu using the Menu button on the camera.
Menu trees The menu trees of the TruVision TVI 3MPX cameras are shown below.
Configuration This section describes how to set up the menu settings. FORMAT Move the cursor to FORMAT, and press the menu button to enter the submenu. Set the format of the camera and confirm. FOCUS Move the cursor to FOCUS and press the menu button to enter the submenu. Move the cursor to FOCUS+, FOCUS-, ZOOM+ and ZOOM- to adjust the camera lens. Note: As TVB-2407/4407 and TVT-2401/4401 are fixed lens cameras, they do not support this feature.
balances the brightness level of the whole image. GAIN This optimizes the clarity of image under poor lighting conditions. Set the gain as HIGH, MIDDLE, or LOW. The higher the gain value, the clearer the image. Select OFF to disable the function. Note: The noise will be amplified if the gain is enabled. FLICKER MODE This is an anti-flicker function that is used when the camera is close to a light source. There are two modes that can be selected: MODE1 and MODE2.
SMART Select to turn on/off the INFRARED and to set the value of SMART IR. INFRARED: Select to turn on/off the IR LED depending on lighting conditions. SMART IR: Use it to avoid over exposure of an image due to IR LED glare. Adjust the SMART IR value from 0 to 3. The higher the value, the more obvious the effects. The option is disabled when the value is 0. VIDEO SETTING Move the cursor to VIDEO SETTING and press the confirm button to enter the submenu.
MIRROR Use this function to flip the original image into a mirror image. This could be used, for example, when the camera needs to be installed upside down. Select one of the functions: DEFAULT: The mirror function is disabled. H: The image flips 180 degrees horizontally. V: The image flips 180 degrees vertically. HV: The image flips 180 degrees both horizontally and vertically. RESET Reset all the settings to the default.
