TruVision Series 3 IP Camera FW3.
Copyright © 2017 United Technologies Corporation. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Manufacturer Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Interlogix. 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
Content Introduction 3 Network access 5 Checking your web browser security level 5 Activating the camera 7 Overview of the camera web browser 9 Camera configuration 11 Configuration menu overview 11 Local configuration 12 System time 13 Network settings 15 Recording parameters 26 Video image 29 OSD (On Screen Display) 33 Overlay text 34 Privacy masks 35 Motion detection alarms 36 Tamper-proof alarms 40 Exception alarms 40 Alarm inputs and outputs 42 Cross line detection 44 Intrusion detection 46 Snapshot pa
Operating PTZ control 67 Index 70 2 TruVision Series 3 IP Camera FW3.
Introduction This is the user manual for TruVision Series 3 IP camera models: IP fixed lens bullet camera: TVB-5301 (2MPX Bullet, 4 mm lens) TVB-5302 (4MPX Bullet, 4 mm lens) IP VF lens bullet camera: TVB-5303 (2MPX Bullet, 2.8 to 12 mm VF lens) TVB-5304 (4MPX Bullet, 2.8 to 12 mm VF lens) IP motorized lens bullet camera: TVB-5305 (2MPX Bullet, 2.8-12 mm VF motorized lens) TVB-5306 (4MPX Bullet, 2.
TVT-5305 (4MPX Turret, 2.8 mm lens, White) TVT-5306 (4MPX Turret, 2.8 mm lens, Black) TVT-5307 (4MPX Turret, 4.0 mm lens, White) 4 TruVision Series 3 IP Camera FW3.
Network access This manual explains how to configure the camera over the network with a web browser. TruVision IP cameras can be configured and controlled using Microsoft Internet Explorer (IE) and other browsers. The procedures described use Microsoft Internet Explorer (IE) web browser. Checking your web browser security level When using the web browser interface, you can install ActiveX controls to connect and view video using Internet Explorer.
Under Reset Custom Settings, click the security level for the whole zone in the Reset To box, and select Medium. Click Reset. Then click OK to the Internet Options Security tab window. 5. Click Apply in the Internet Options Security tab window. Windows users Internet Explorer for Windows operating systems have increased security measures to protect your PC from any malicious software being installed.
Activating the camera When you first start up the camera, the Activation window appears. You must define a high-security admin password before you can access the camera. There is no default password provided. You can activate a password via a web browser and via TruVision Device Manager (included on the CD to find the IP address of the camera). To activate the camera via the web browser: 1. Power on the camera and connect the camera to the network. 2.
3. Enter the password in the password field, and confirm it. Note: A valid password range must be between 8 and 16 characters. You can use a combination of numbers, lower and upper case letters, and special characters : _ - , . * & @ / $ ? Space. The password must contain characters from at least two of these groups. We also recommend that you reset your password regularly. For high security systems, it is particularly recommended to reset the password monthly or weekly for better protection. 4.
Overview of the camera web browser The camera web browser lets you view, record, and play back recorded videos as well as manage the camera from any PC with Internet access. The browser’s easy-to-use controls give you quick access to all camera functions. See Figure 1 below. If there is more than one camera connected over the network, open a separate web browser window for each individual camera.
Name Description 8. Aspect ratio Select the aspect. 9. Streaming Switch between main stream and substream. 10. Viewer View live video. Time, date and camera name are displayed here. 11. Start/stop live view Click to start/stop live view. 12. Audio Adjust volume. 13. Manual Alarm Click to trigger the alarm output. 14. Bidirectional audio Turn on/off microphone. 15. Capture Click to take a snapshot of the video. The snapshot will be saved to the default folder in JPEG format. 16.
Camera configuration This chapter explains how to configure the cameras through a web browser. Once the camera hardware has been installed, configure the camera’s settings through the web browser. You must have administrator rights in order to configure the cameras over the internet. The camera web browser lets you configure the camera remotely using your PC. Web browser options may vary depending on camera model.
Configuration folders Description 2. Network Defines the network parameters required to access the camera over the internet. See “Network settings” on page 15 for more information. 3. Video/Audio Defines recording parameters. See “Recording parameters” on page 26 for more information. 4. Image Defines the image parameters, OSD settings, overlay text, and privacy mask.
Table 3: Overview of the Local configuration window Parameters Description Live View Parameters 1. Protocol Specifies the network protocol used. Options include: TCP, UDP, MULTICAST and HTTP. 2. Live View Performance Specifies the transmission speed. Options include: Shortest Delay or Auto. 3. Rules It refers to the rules on your local browser. Specify whether or not to display the colored marks when motion detection, face detection, and intrusion detection are triggered.
2. From the Time Zone drop-down menu select the time zone that is the closest to the camera’s location. 3. Under Time Sync, check one of the options for setting the time and date: Synchronize with an NTP server: Check the NTP enable box and enter the server NTP address. The time interval can be set from 1 to 10080 minutes. - Or Set manually: Enable the Manual Time Sync. function and then click set the system time from the pop-up calendar.
Network settings Accessing the camera through a network requires that you define certain network settings. Use the “Network” folder to define the network settings. See Figure 4 and Table 4 below for further information. Figure 4: Network window (TCP/IP tab shown) Table 4: Network parameters Parameters Description 1. NIC Type: Specifies the NIC type. Default is Auto. Other options include: 10M Half-dup, 10M Full-dup, 100M Half-dup and 100M Full-dup.
Parameters Description network storm. Enable Multicast Discovery: Enables the automatic detection of the online network camera via private multicast protocol in the LAN. DNS server: Specifies the preferred and alternate DNS server for your network. 2. Port HTTP Port: The HTTP port is used for remote internet browser access. Enter the port used for the Internet Explorer (IE) browser. Default value is 80.
Parameters Description 8. The UPnP (Universal Plug and Play) protocol allows devices to connect seamlessly and to simplify the implementation of networks in the home and corporate environments. With the function enabled, you do not need to configure the port mapping for each port, and the camera is connected to the Wide Area Network (WAN) via the router. NAT Enable and set the friendly name detected. 9.
2. Set the HTTP port, RTSP port, HTTPS port, and server port of the camera. HTTP Port: The default port number is 80. It can be changed to any port number that is not occupied. RTSP Port: The default port number is 554. It can be changed to any port number in the range from 1 to 65535. HTTPS Port: The default port number is 443. It can be changed to any port number that is not occupied. Server Port: The default server port number is 8000. It can be changed to any port number in the range from 2000 to 65535.
• DynDNS: Enter the DNSS server address, members.ddns.org, which is used to notify DDNS about changes to your IP address, the host name for your camera, the port number (443 (HTTPS)), and your user name and password used to log into your DDNS account. The domain name displayed under “Host Name” is that which you created on the DynDNS web site. • ezDDNS: Enter the desired host name under “Host Name”. The default host name is utc-serial number. The new host name is registered when you click Save.
To define the SNMP parameters: 1. Click Configuration > Network > SNMP. 2. Select the corresponding version of SNMP: v1, v2c, v3, or “Other Settings”. 3. Configure the SNMP settings. The configuration of the SNMP software should be the same as the settings you configure here. 4. Click Save to save changes. Note: Before setting the SNMP, please download the SNMP software and ensure that you can receive the camera information via the SNMP port.
To define the 802.1X parameters: 1. Click Configuration > Network > 802.1X. Check Enable IEEE 802.1X to enable the feature. Configure the 802.1X settings, including EAPOL version, user name, and password. The EAPOL version must be identical with that of the router or the switch. Click Save to save changes. To define the QoS parameters: 1. Click Configuration > Network > QoS. 2. Configure the QoS settings, including Video / Audio DSCP, Event / Alarm DSCP, and Management DSCP.
To define the FTP parameters: 1. Click Configuration > Network > FTP. 2. Configure the FTP settings, including server address, port, user name, password, directory, and upload type. Anonymous: Check the check box to enable the anonymous access to the FTP server. Directory: In the Directory Structure field, you can select the root directory, main directory and subdirectory.
2. Check the check box to enable the UPnP function. You can edit the name of the device when detected online. 3. Click Save to save changes. To set up the Email parameters: 1. Click Configuration > Network > Email. 2. Configure the following settings: Sender: The name of the email sender. Sender’s Address: The email address of the sender. SMTP Server: The SMTP server IP address or host name. SMTP Port: The SMTP port. The default is 25.
User Name: The user name to log in to the server where the images are uploaded. Password: Enter the password. Confirm: Confirm the password. Receiver1: The name of the first user to be notified. Receiver’s Address1: The email address of user to be notified. Receiver2: The name of the second user to be notified. Receiver’s Address2: The email address of user to be notified. Receiver3: The name of the third user to be notified. Receiver’s Address3: The email address of user to be notified. 3.
2. To create a self-signed certificate: Click the Create button beside “Create Self-signed Certificate”. Enter the country, host name/IP, validity and the other information requested. Click OK to save the settings. -OrTo create a certificate request: Click the Create button beside “Create Certificate Request”. Enter the country, host name/IP and the other information requested. TruVision Series 3 IP Camera FW3.
3. Click OK to save the settings. Download the certificate request and submit it to the trusted certificate authority for signature, such as Symantec or RSA. After receiving the signed valid certificate, upload the certificate to the device. Recording parameters You can adjust the video and audio recording parameters to obtain the picture quality and file size best suited to your needs. Figure 5 and Table 5 below list the video and audio recording options you can configure for the camera.
Tab Description Resolution: Specifies the recording resolution. A higher image resolution provides a higher image quality but also requires a higher bit rate. The resolution options listed depend on the type of camera and on whether main or substream is being used. Note: Resolutions can vary depending on the camera model. Bitrate Type: Specifies whether variable or fixed bit rate is used. Variable produces higher quality results suitable for video downloads and streaming. Default is Constant.
To define ROI parameters: 1. Click Configuration > Video/Audio > ROI. 2. Draw the region of interest on the image. It supports only one region. 3. Choose the stream type to set the ROI encoding. 4. Check the Fixed Region to manually configure the area. You can choose the Image Quality Enhancing level for ROI encoding, and you can also name the ROI area. 5. Click Save to save changes.
3. Click Save to save changes. Video image You may need to adjust the camera image depending on the camera model or location background in order to get the best image quality. You can adjust the brightness, contrast, saturation, hue, and sharpness of the video image. Use this menu to also adjust camera behavior parameters such as exposure time, iris mode, video standard, day/night mode, image flip, WDR, digital noise reduction, and white balance. See Figure 6 and Table 6 below for more information.
Parameter Description sharpness), Exposure (Exposure Time and gain), Backlight, White Balance and Image Enhancement settings for day mode only. Night: Configure the Image Adjustment (Brightness, Contrast and sharpness), Exposure (Exposure Time and gain), Backlight, White Balance and Image Enhancement settings only. Custom 24h settings This is used when the camera is in an outdoor situation where the day/night change is defined by the amount of daylight or a trigger via an alarm input.
Parameter Description 3. Exposure Settings Iris Mode Only “Manual” is available. Exposure Time The exposure time controls the length of time that the aperture is open to let light into the camera through the lens. Select a higher value if the image is dark and a lower value to see a fast moving object. Gain Select a value to adjust the image brightness. Day/Night Switch This option appears when the Common option is selected. Day/Night Switch Defines whether the camera is in day or night mode.
Parameter IR Light Description Select On/OFF to enable/disable IR. Enable: The IR illuminators are On when the camera turns into night mode. Disable: The IR illuminators are Off when the camera turns into night mode. Note: The IR illuminators always are Off in daytime mode. 4. Backlight Settings BLC Area BLC (backlight compensation) can improve image quality when the background illumination is high. It prevents the object from appearing too dark. Select Off, Up, Down, Left, Right or Center.
Parameter Hallway View Description In a vertical-shaped scene, such as a hallway or corridor, the image is shown with a vertical (tall) rather than horizontal (wide) format. The video image is at a 9:16 aspect ratio. During installing, turn the camera to 90 degrees or rotate the 3-axis lens to 90 degrees, and then set the rotate mode as On. You will get a normal view of the scene with 9:16 aspect ratio that ignores needless information such as the walls. Default is Off.
4. Check the Display Week box (3) to include the day of the week in the onscreen display. 5. In the Camera Name box (4), enter the camera name. 6. Select the time and date formats from the Time format and Date format list boxes (5). 7. Select a display mode for the camera from the Display Mode list box (6). Display modes include: • Not transparent & Not Flashing. The image is behind the text. This is default. • Not transparent & Flashing. The image is behind the text. The text flashes on and off.
Figure 7: Text overlay menu To add on-screen text: 1. Click Configuration > Image > Text Overlay. 2. Check the text box for the text. 3. Enter the text in the text box. 4. Use the mouse to click and drag the red text in the live view window to adjust the text overlay position. 5. Click Save to save changes. Privacy masks Privacy masks let you conceal sensitive areas (such as neighboring windows) to protect them from view on the monitor screen and in the recorded video.
Figure 8: Privacy mask menu To add privacy mask area: 1. Click Configuration > Image > Privacy Mask. 2. Check Enable Privacy Mask. 3. Click Draw Area. 4. Click and drag the mouse in the live video window to draw the mask area. Note: You are allowed to draw up to four areas on the same image. 5. Click Stop Drawing to finish drawing, or click Clear All to clear all of the areas you set without saving them. 6. Click Save to save changes. Motion detection alarms You can define motion detection alarms.
Figure 9: Motion detection menu Defining a motion detection alarm requires the following tasks: 1. Area settings: Define the on-screen area that can trigger a motion detection alarm and the detection sensitivity level. 2. Arming schedule: Define the schedule during which the system detects motion. 3. Recording schedule: Define the schedule during which motion detection can be recorded. See “Recording schedule” on page 50 for further information. 4. Linkage: Specify the method of response to the alarm.
6. Move the Sensitivity slider to set the sensitivity of the detection. All areas will have the same sensitivity level. 7. Click Edit to edit the arming schedule. See the picture below for the editing interface of the arming schedule. 8. Choose the day and click schedule to other days. to set the detailed time period. You can copy the 9. Click OK to save changes. 10. Specify the linkage method when an event occurs.
To set up motion detection in advanced mode: 1. Click Configuration > Basic Event > Motion Detection. 2. Check the Enable Motion Detection box. Check Enable Dynamic Analysis for Motion if you want to see where has motion real-time. Note: Select Disable for rules in local configuration menu if you don’t want the detected objected displayed with the rectangles. 3. Select Advanced mode from the drop down menu. 4. Select OFF, Auto-switch or Scheduled-switch 5. Select Area No. and click Draw Area.
Trigger Alarm Output Trigger external alarm outputs when an event occurs. Note: This option is only supported by cameras that support an alarm output. 12. Click Save to save changes. Tamper-proof alarms You can configure the camera to trigger an alarm when the lens is covered and to take an alarm response action. To set up tamper-proof alarms: 1. Click Configuration > Basic Event > Tamper-proof. 2. Check the Enable Tamper-proof box. 3. Move the Sensitivity slider to set the sensitivity of the detection.
• Network Disconnected: Disconnected network cable. • IP Address Conflicted: Conflict in the IP address setting. • Invalid Login: Wrong user ID or password used to log in to the cameras. Figure 10: Exception menu To define exception alarms: 1. Click Configuration > Basic Event > Exception. 2. Under Notification Type, select an exception alarm type from the drop-down list. 3. Check the check box to select the linkage method. 4. Click Save to save changes. TruVision Series 3 IP Camera FW3.
Alarm inputs and outputs To define the external alarm input: 1. Click Configuration > Basic Event > Alarm Input. 2. Choose the Alarm Input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). Enter a name for the alarm input. 3. Click Edit to set the arming schedule for the alarm input. See “Motion detection alarms” on page 36 for more information. 4. Check the desired check box to select the linkage method. 5. Click Save to save changes.
To define the alarm output: 1. Click Configuration > Basic Event > Alarm Output. 2. Select an alarm output channel from the Alarm Output drop-down list. You can also set a name for the alarm output. 3. The delay time can be set to 5 s, 10 s, 30 s, 1 min, 2 min, 5 min or 10 min. The delay time refers to the time duration that the alarm output remains in effect after the alarm occurs. 4. Click Edit to set the arming schedule for the alarm input. See “Motion detection alarms” on page 36 for more information.
Cross line detection This function can be used to detect people, vehicles and objects crossing a predefined line or an area. The line crossing direction can be set as bi-directional, for example, from left to right or from right to left. A series of linkage methods can also be triggered if an object crossing the line is detected. Figure 11: Cross line menu To define Cross Line Detection: 1. Click Configuration > Smart Event > Cross Line. 2. Check the Enable Cross Line check box to enable the function. 3.
6. Click Edit to set the arming schedule for the alarm input. See “Motion detection alarms” on page 36 for more information. 7. Configure the linkage action. 8. Click Save to save changes. TruVision Series 3 IP Camera FW3.
Intrusion detection Intrusion detection allows you to set up an area in the surveillance scene. If someone enters the area, a set of alarm actions can be triggered. Figure 12: Intrusion Detection menu To define intrusion detection: 1. Click Configuration > Smart Event > Intrusion Detection. 2. Check the Enable Intrusion Detection check box to enable the function. 3. Click Draw Area, and then draw a rectangle on the image as a defense region.
5. Click Edit to set the arming schedule for the alarm input. See “Motion detection alarms” on page 36 for more information. 6. Configure the linkage action. 7. Click Save to save changes. Snapshot parameters You can configure scheduled snapshots and event-triggered snapshots. The captured snapshots can be stored in the SD card (if supported) or the NAS. You can also upload the snapshots to an FTP server. You can set up the format, resolution and quality of the snapshots.
Figure 13: Snapshot menu To set up scheduled snapshots: 1. Click Configuration > Storage > Snapshot. 2. Check Enable Timing Snapshot to enable continuous snapshots. 3. Select the desired format of the snapshot, such as JPEG. 4. Select the desired resolution of the snapshot. 5. Select the desired quality of the snapshot: High, Medium, or Low. 6. Enter the time interval between two snapshots. Select the unit of time from the dropdown list: milliseconds, seconds, minutes, hour, or day. 7.
To set up event-triggered snapshots: 1. Click Configuration > Storage > Snapshot. 2. Check Enable Timing Snapshot to enable continuous snapshots. 3. Select the desired resolution and quality of the snapshot. 4. Enter the time interval between two snapshots. Select the unit of time from the dropdown list: milliseconds, seconds, minutes, hour, or day. 5. Under Capture Number, enter the total number of snapshots that can be taken. 6. Click Save to save changes.
To set up a NAS system: 1. Click Configuration > Storage > NAS. 2. Enter the IP address of the network disk, and the NAS file path. 3. Click Save to save changes. Storage devices Use the storage management window to display the capacity, free space available and the working status of the HDD of the NAS and the SD card in the camera. You can also format these storage devices. Before formatting the storage device, stop all recording.
Pre-record time The pre-record time is set to start recording before the event. For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the camera starts to record the event at 9:59:55. The pre-record time can be configured as “No Pre-record”, 5 s, 10 s, 15 s, 20 s, 25 s, 30 s, or “Not limited”. Post- record time The post-record time is set to stop recording after the event.
4. Select whether the recording will be for the whole week (All Day recording) or for specific days of the week (Customize recording). All Day recording: Select one of the record types to record from the dropdown list box: • Normal: This is continuous recording. • Motion Detection: The video is recorded when the motion is detected. • Alarm: The video is recorded when the alarm is triggered via the external alarm input.
Set the customized recording periods for the other days of the week, if required. Click Copy to copy the recording periods to another day of the week. 5. Click OK and Save to save changes. Note: If you set the record type to “Motion detection”, “Alarm”, “Cross Line” or “Intrusion Detection” you must also define the arming schedule in order to trigger the recording. TruVision Series 3 IP Camera FW3.
Camera management This chapter describes how to use the camera once it is installed and configured. The camera is accessed through a web browser. User management This section describes how to manage users. You can: Add or delete users Modify permission Modify passwords Only the administrator can manage users. The administrator can create up to 31 individual users for the cameras listed in this manual.
Admin: This is the system administrator. The administrator can configure all settings. Only the administrator can create and delete user accounts. Admin cannot be deleted. Operator: This user can only change the configuration of his/her own account. An operator cannot create or delete other users. Viewer: This user has the permission to live view, play back and search logs. However, Viewers cannot change any configuration settings.
Basic Permission Camera Configuration Remote: Parameters Settings Remote: Live View Remote: Log Search/Interrogate Working Status Remote: PTZ Control Remote: Upgrade/Format Remote: Playback Remote: Manual Record Remote: Bidirectional Audio Remote: Shutdown / Reboot Remote: Notify Alarm Recipient / Trigger Alarm Output Remote: Video Output Control Remote: Serial Port Control 7. Click OK to save the settings. To delete a user: 1. Select one user in the User tab. 2. Click Delete button.
To define RTSP authentication: 1. Click Configuration > Storage > RTSP Authentication. 2. Under “RTSP Authentication”, select Enable or Disable in the drop-down list to enable or disable the RTSP authentication. 3. Click Save to save the changes. Note: If "RTSP Authentication" is disabled, the user can still see the live view images although there is has no permission for “Remote: Live View". IP address filter This function makes access control possible.
2. Select the IP Address Filter tab. 3. Check the Enable IP Address Filter check box. 4. Select the type of IP Address Filter in the drop-down list, Forbidden or Allowed. 5. Click Add to add an IP address. 6. Click Modify or Delete to modify or delete the selected IP address. 7. Click Clear to delete all the IP addrsses. 8. Click Save to save the changes. Defining the security service The camera provides a security service by allowing you to enable remote login and to improve data communication security.
To restore default settings: 1. Click Configuration > System > Maintenance. 2. Click either Restore or Default. A window showing user authentication appears. 3. Enter the admin password and click OK. 4. Click OK in the pop-up message box to confirm restoring operation. Import/export a configuration file The administrator can export and import configuration settings from the camera. This is useful if you want to copy the configuration settings to a camera, or if you want to make a backup of the settings.
You need to upgrade firmware when it has become outdated. When you upgrade the firmware, all existing settings are unchanged. Only the new features are added with their default settings. The camera will select the corresponding firmware file automatically. Cookies and data in the web browser are automatically deleted when the firmware is updated. To upgrade firmware version: 1. Download on to your computer the latest firmware from our web site at: www.interlogix.
Camera operation This chapter describes how to use the camera once it is installed and configured. Logging on and off You can easily log out of the camera browser window by clicking the Logout button on the menu toolbar. You will be asked each time to enter your user name and password when logging in. Figure 17: Login dialog box If you do not change the default password of admin, a message will always pop up requesting you to do so: You are requested to change the default password immediately.
Live view mode Once logged in, click “Live View” on the menu toolbar to access live view mode. See Figure 1 on page 9 for the description of the interface. Start/stop live view: You can stop and start live view by clicking the Start/stop live view button on the bottom of the window. Record: You can record live video and stored it in the directory you have configured. In the live view window, click the Record button at the bottom of the window. To stop recording, click the button again.
Figure 18: Playback window Name Description 1. Playback button Click to open the Playback window. 2. Search calendar Click the day required to search. 3. Search Start search. 4. Set playback time Input the time and click 5. Control playback Click to control how the selected file is played back: play, stop, slow and fast forward playback. 6. Timeline bar The timeline bar displays the 24-hour period of the day being played back. It moves left (oldest) to right (newest).
Name Description 9. The color code displays the recording type. Recording types are schedule recording, alarms recording and manual recording. Recording type The recording type name is also displayed in the current status window. 10. Archive functions Click these buttons for the following archive actions: Capture a snapshot image of the playback video. Start/Stop clipping video files. To play back recorded video 1. Select the date and click the Search button.
To archive recorded snapshots: 1. Click to open the snapshots search window. 2. Select the snapshot type as well as the start and end time. 3. Click Search to search for the snapshots. 4. Select the desired snapshots, and click Download to download them. Searching event logs You must configure NAS or insert a SD card in the dome camera to be able to use the log functions. The number of event logs that can be stored on NAS or SD card depends on the capacity of the storage devices.
Figure 19: Log window 1. Major Type 4. Start search 2. Minor Type 5. Save searched logs 3. Start and end search time You can search for recorded logs by the following criteria: Major type: There are three types of logs: Alarm, Exception, and Operation. You can also search “All”. See Table 7 below for their descriptions. Minor type: Each major type has some minor types. See Table 7 below for their descriptions. Date and Time: Logs can be searched by start and end recording time.
Log type Description of events included Operation Power On, Unexpected Shutdown, Remote Reboot, Remote Login, Remote Logout, Remote Configure parameters, Remote Upgrade, Remote Start Record, Remote Stop Record, Remote PTZ control, Remote Initialize HDD, Remote Playback by File, Remote Playback by Time, Remote Export Config file, Remote import config file, Remote Get Parameters, Remote Get Working Status, Start Bidirectional Audio, Stop Bidirectional Audio, Remote Alarm Arming, Remote Alarm Disarming To
Description 7. Initializes the lens Note: 1. To do pan/tilt movement using the direction buttons, the camera connected to the network must support RS-485 and a pan/tilt unit must be installed in the camera. Please properly set the PTZ parameters on the RS-485 Settings page referring to Defining RS-485 settings 2. To control the lens, such as zoom or focus, the camera must support auto focus. To set a preset: 1. Select a preset number from the preset list. 2.
To set a preset tour: 1. In the PTZ control panel, click to enter the tour settings interface. 2. Select a preset tour number from the drop-down list. 3. Click to enter the adding interface of preset. 4. Configure the preset number, preset tour time and preset tour speed. Preset Tour Duration: The dwell time. The length of time in seconds for which a camera stays at a preset before moving to the next preset. Preset Tour Speed: The speed the camera moves from one preset to another. 5.
Index A H Activate the camera, 7 Alarm inputs set up, 42 Alarm outputs set up, 42 Alarm types motion detection, 36 Archived files play back, 64 Archiving files recorded files, 64 snapshots of recorded files, 64 Audio parameters, 26 HDD capacity, 50 formatting, 50 HDD error alarm, 40 HDD full alarm, 40 B Live view manual recording, 62 snapshots, 62 start/stop, 62 Live view parameters, 12 Local camera parameters, 12 Logging on and off, 61 Logs information type, 66 search logs, 65 view logs, 65 Backlight
Pre-recording times description, 51 Privacy masks, 35 PTZ control, 67 Q QoS parameters set up, 21 R Reboot camera, 60 Record file settings, 12 Recording define recording schedule, 50 manual recording, 62 parameters, 26 playback, 62 Resolution, 26 RTSP authentification, 56 modify computer ID, 56 types of users, 54 V Video parameters, 26 Video quality, 29 W Web browser overview of the interface, 9 Web browser security level checking, 5 White balance, 29 S SDHC card capacity, 50 card full, 50 formatting,
