UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual P/N 1072553A • REV 1.
Copyright Trademarks and patents © 2012 UTC Fire & Security. All rights reserved. The TruVision and Interlogix names and logo are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Manufacturer UTC Fire & Security Americas Corporation, Inc. 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
Content Product overview 2 Package Contents 2 Features 2 User guidelines 2 Product description 3 OSD control pad 3 Installation 5 Mount the camera 5 Connect the cables 5 Adjust the lens 5 Adjust the focus and zoom 6 Programming 7 Access the Main menu 7 General menu 7 AE/WDR/BLC menu 8 WB mode menu 9 D/N mode menu 9 Motion alarm menu 10 Privacy menu 11 Picture adjustment menu 12 Reset camera 12 Specifications 12 Dimensions 13 Menu Map 14 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual 1
Product overview The UVD-6120VE-2-XX camera uses a digital signal processor (DSP) to process video signals. The camera includes a microcontroller to provide high-quality images with high-color reproduction and sharp pictures. Package Contents The package contains the following: • Dome camera • Monitor output cable • Mounting screws, wall anchors, and hex wrench • Power terminal • Ceiling drilling holes template Note: Use the video output BNC and power jack for normal system operation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the camera. • Do not use the camera over the temperature range specifications: - 22 to 122°F (-30 to +50°C). • If the light source where the camera is installed experiences rapid, widevariations in lighting, the camera may not operate as intended. WARNING: To reduce the risk of fire or electronic shock, do not expose the camera to rain or moisture and do not remove the cover or back.
Figure 2: OSD control pad OSD control pad Table 1: OSD control pad functions Pad directions Description Up Moves the cursor upward to select an item. Left Moves the cursor left to select or adjust the options of the selected item. Right Moves the cursor to the right to select or adjust the options of the selected item. Down Moves the cursor downward to select an item. Enter Press the center of the control pad to display the Setup menu.
Installation Please check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. To install the camera you will need to prepare the mounting surface, mount the camera, make cable connections, adjust the lens and then secure the dome cover securely. Note: Before installing, please ensure that the mounting surface is strong enough to withstand three times the weight of the camera.
Figure 3: Camera adjustment Platform horizontal adjustment (0 to 180°) Platform vertical adjustment (0 to 90°) Rotor horizontal adjustment (0 to 350°) To adjust the lens: See Figure 3 above. 1. To adjust the horizontal angle of the platform up to 180 degrees, turn the platform. 2. To adjust the horizontal angle of the rotor up to 350 degrees, turn the rotor on the platform. 3. To adjust the vertical angle of the platform up to 90 degrees, turn the platform.
Programming Access the Main menu The Main menu provides access to the camera configuration options. The onscreen display (OSD) is only available in English. Program the camera by attaching a standard video monitor to the system. Figure 5: The Main menu To access the menus: 1. Press the OSD control pad to access the Main menu and its submenus. 2. Push the pad up, down, left and right to move between menu options. 3. Press the OSD control pad (Enter) to select an option. 4.
Parameter Description Default option is Off. DNR Digital noise reduction (DNR) improves the image quality in low light levels. When enabled, select the Y and C filter strength: Press Return to return to the previous menu or Exit & Save to save changes and return to live mode. Default option is On. Return Press Enter to return to the previous menu. Exit & Save Exits the menu and returns to live mode. Saves changes made.
WB mode menu White balance (WB) tells the dome camera what the color white looks like. Based on this information, the dome camera will then continue to display all colors correctly even when the color temperature of the scene changes such as from daylight to fluorescent lighting, for example. Select the W/B Mode option from the Main menu to enter the WB Mode menu.
Table 5: D/N mode menu Menu item Description Auto When set to Auto Day/Night mode, the camera produces high-quality color video during the day or when light levels are high. It then switches to monochrome and removes the infrared filter to improve IR sensitivity at night or when light levels are low. Set following parameters: Day→Night: Set the threshold level on how dark it should be before switching from Day to Night mode.
Table 6: Motion alarm menu Menu item Description Motion Detec. When enabled, you can set up four motion detection areas (Labels) on screen.
Table 7: Privacy menu Menu item Description Mask 1 Setup When enabled, you can set up four privacy mask areas on screen.
Model UVD-6120VE-2-P / UVD-6120VE-2-N Power consumption 3W Max: 9.6 W (heater on) Operating temperature -30 to +50°C (- 22 to 122°F) Weight 1130 g (2.
Menu Map 14 UltraView UVD-6120VE-2 Digital WDR Dome Camera User Manual
