Instructions / Assembly

ManualsBrandsIntermatic ManualsOutdoorsRC600 Series Radio Receiver with Manual On/Off Button in Beige

INSTALLATION

OPERATION &

SERVICE MANUAL

SINGLE CHANNEL RADIO RECEIVERS

Model: RC613, RC613L Switching Module

For indoor and outdoor use, suitable for Pool/Spa equipment control

ELECTRICAL RATING: 15 A Resistive, 1200 W Tungsten, 1 HP Motor Load - 120 V

GENERAL INFORMATION

RC SERIES

REMOTE CONTROLS

THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation of this device is subject to the following two conditions

1) This device may not cause harmful interference. 2) This device must accept any interference that may be received,

including interference that may cause undesired operation. FCC rules prohibit adjustments to or modication of receiver

and transmitter circuitry except for replacing the remote control battery. THERE ARE NO OTHER USER SERVICEABLE

PARTS.

WARNING

• Installation and/or wiring must be in accordance with national and local electrical code.

• Use COPPER conductors ONLY.

• The control panel to be a minimum of 3m (in Canada) or 5ft (in USA) from the inside wall of the pool, spa, or pond, unless separated from the

body of water by a fence, wall or other permanent barrier that will make the unit inaccessible to persons in the water.

• Do NOT exceed maximum current carrying capacity.

• This enclosure does not provide grounding between conduit connections. When metallic conduit is used, you must also install grounding type

bushings and jumper wire, in accordance with the (NEC) National Electrical Code requirements.

• This control should not be connected to any equipment which would cause bodily injury property damage should it be activated unexpectedly.

• Disconnect power at circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualiﬁed service technician.

Risk of Fire or Electric Shock

These Modular Radio Receivers are one half of a two part remote control

system. They operate as ordinary ON/OFF switches but they also respond

to the signals of a hand held transmitter - the other half of the system.

The modules are designed for indoor or outdoor use, and can handle a

variety of switching applications, typical around the house or farm. By the

push of a button on the face of the transmitter, the user is able to turn

ON/OFF the connected load (lights, pump, etc.) from any remote location*,

safely and conveniently. In addition, a single transmitter can operate up

to three Receivers and is able to “teach” each Module a different code.

(Transmitters are sold separately).

Model RC613 Receiver Module comes with its own manual ON/OFF

button and it is intended to be installed at the location of the load. The

connected load may be turned ON/OFF using the hand-held transmitter

or turned ON/OFF by pushing the red button on the face of the Receiver.

Model RC613L Receiver Module is the same as RC613 except that it

comes with extra long (36 in.) leads.

* The open eld range is approximately 200 feet or less, but depends on

many factors like the age of the battery, proximity of large metal objects,

the location of the receiver and environmental conditions at the time of

transmission.

Summary of content (4 pages)

PAGE 1
RC SERIES REMOTE CONTROLS INSTALLATION OPERATION & SERVICE MANUAL SINGLE CHANNEL RADIO RECEIVERS Model: RC613, RC613L Switching Module For indoor and outdoor use, suitable for Pool/Spa equipment control ELECTRICAL RATING: 15 A Resistive, 1200 W Tungsten, 1 HP Motor Load - 120 V THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation of this device is subject to the following two conditions 1) This device may not cause harmful interference.
PAGE 2
SPECIFICATIONS AND OTHER INFORMATION USEFUL INFORMATION 1. Must be mounted upright. Antenna must be up. 2. Radio Receivers are sensitive to heat. Avoid mounting them above heater, air conditioner or exposed to afternoon sun. 3. The higher the Receiver Module, the longer its range. For good range and reliable reception, install modules as high as practical above ground level with antenna at top. 4. Large metal objects divert radio signals.
PAGE 3
OPERATION Linking RC939 Transmitter Button with the RC613 Receiver 1. To clear any existing codes, press and hold the blue code set button on the receiver for 15 seconds then release. 2. Now insert a paper clip in the hole on the bottom right side of remote and get the red light on the bottom to light up. (NOTE: Illuminated LED may be difficult to see in direct sunlight.) 3. To link the reciever and transmitter, go back to the receiver and press & release the blue code set button. 4.
PAGE 4
TROUBLESHOOTING Symptom Possible Cause(s) Corrective Action No response to transmitter signal at any time No power Turn ON power at main panel Loose connection(s) at receiver and/or load Check connections Transmitter battery dead Replace battery Receiver and transmitter are on 2 different codes Link transmitter button with the receiver (see page 3, Operating instructions) Faulty transmitter Check battery connections, replace transmitter Faulty receiver Replace receiver module Weak battery R