User Guide

ManualsBrandsIntermatic ManualsOtherWP1000RC

158WP12465

ITEM

. NO.

DESC. QUAN.

DR.: SRB 9/8/2005

INTERMA

TIC INCORPORATED

CHKD.: TS 9/8/2005

SCALE:

NAME:

INST SHT - INST

ALL, WP1000RC

APPROVED MATL.:

WHITE PAPER STOCK

TD 9/8/2005

FINISH:

BLACK PRINTING INK

1 RELEASED TO ELEC. DATA

HEAT TREAT:

LET. REVISION SIGN. MODEL SUPERSEDES:

NOTES:

ALL PRINTING TO BE AS PER INTERMATIC

APPROVED ARTWORK.

FRACTIONS + .010 . DECIMALS

AS SPECIFIED -

ANGLES + 1/2˚

ALL DIMENSIONS MUST BE MET BEFORE PLATING.

DIM

TOL

11”

8.5”

SEE B/M FOR ALL PART NUMBERS & QUANTITIES

FOLD LINE

FRONT

BACK

LIMITED 1

YEAR W

ARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or

workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge.

This

warranty is extended to the original household purchaser only and is not transferable.

This warranty does

not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any

negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise

modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product;

(e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such

as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial

installation costs, removal costs, or reinstallation costs.

INTERMA

TIC INCORPORA

TED WILL

NOT BE LIABLE FOR INCIDENT

AL OR CONSEQUENTIAL

DAMAGES. SOME ST

TES DO NOT

ALLOW THE EXCLUSION OR LIMIT

ATION OF INCIDENTAL OR

CONSEQUENTIAL

DAMAGES, SO THE

ABOVE LIMIT

TION OR EXCLUSION MAY NOT APPLY TO

YOU. THIS W

ARRANTY

IS IN LIEU OF

ALL

OTHER EXPRESS OR IMPLIED WARRANTIES. ALL

IMPLIED W

ARRANTIES, INCLUDING THE W

ARRANTY

OF MERCHANT

ABILITY AND THE

ARRANTY

OF FITNESS FOR

PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY

AS CONT

AINED IN THIS LIMITED W

ARRANTY

AND SHALL BE OF THE SAME DURATION AS THE

ARRANTY

PERIOD ST

ATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE

DURA

TION OF

AN IMPLIED W

ARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was

purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized

service center listed below

This warranty is made by: Intermatic Incorporated/After Sales Service/7777

inn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www

.intermatic.com Please be sure to

wrap the product securely to avoid shipping damage.

158WP12465

Pg.4

Mounting Siding Flange (figures 3 and 4)

1. Position Siding Flange over Junction Box opening and mount to plywood

using nails or screws (not provided).

2. Siding and other materials may be installed using flange as a channel to

provide a clean finish.

Brick Mounting (figure 5)

1. Cut off Stud Brackets and Plywood Brackets.

2. Leave Junction Box to be positioned in brickwork with opening set back 1/8”

or more inside brick.

Fig. 3

Fig. 4

Fig. 5

Siding Flange

Stucco Mounting (figure 6)

1. Cut off Stud Brackets.

2. Cut hole in plywood or block (if block construction).

3. Secure Junction box using plywood brackets and screws or nails (not provided).

Finish Mounting (figure 7)

Select insert for appropriate device to be installed.

2. Remove any mounting screws provided with the device.

3. Mount device to insert using screws provided.

4. Snap Insert with device into Recessed Sleeve.

5. Wire device according to device manufacturers instructions.

6. Slide Recessed Sleeve into Junction Box as far back as necessary for gasket.

7. Secure Sleeve to Junction Box using screws provided.

Snap hinged Cover into place.

Fig. 6

Fig. 7

Cover

Gasket

Insert

Screws to Secure

Sleeve

Recessed Sleeve

Pg 2

Pg.3

MODEL: WP1000RC

MOUNTING INSTRUCTIONS FOR

FLUSH MOUNT WHILE-IN-USE COVER

First, determine the method to mount the Junction Box (plywood or stud).

Plywood Mount (figure 1)

1. Use Junction Box opening as template to cut hole in plywood.

2. Cut off two stud mounting brackets.

3. Slide Junction Box through plywood opening and mount using nails or

screws (not included).

Stud Mount (figure 2)

1. Position Junction Box along stud with opening extending between 1/2” and 1”

past front of stud and mount with nails or screws (not provided). Note: the

depths may vary depending upon expected finish material - plywood, wrap,

foam board, siding, etc.

2. Cut off two plywood mounting brackets if necessary (or use as a guide)

Fig. 1

Fig. 2

Junction Box

Pg.1