Product Name: BT board Brand Name: Intermec Model No: INBT02 User’s Guide 1
Introduction INBT02 is a Bluetooth Module. This can be made to connect to other Bluetooth wireless devices by integrating the INBT02 module to the user’s device for which Bluetooth functionality is targeted. The module block diagram is shown Figure 1 Figure 1: INBT02 - Block Diagram It consists of 3 main portions 1. Antenna – Transmit/Receive RF Signal to/from other Bluetooth devices 2. BT Module – BM 180 – Used for Transmit/ Receive data to and from other Bluetooth devices 3.
The Pin assignment is listed in Table 1. 1 Ground 2 Power, 3.3V 3 Data_Exit 4 Host_Wake 5 Host_Sleep 6 BT_LED 7 Ground 8 CMD_Data 9 UART_RTS 10 UART_TX 11 UART_CTS 12 UART_RX 13 Power, 3.3V 14 Ground Table 1.Connector Pin-out Specifications Product Name BT board Model Number INBT02 Standard V2.1+EDR Frequency Band 2.4GHz ~ 2.
Regulatory Information The Bluetooth radio is designed to be interoperable with any Bluetooth technology product that is based on frequency hopping spread spectrum (FHSS) radio technology and complies with the Bluetooth Specification Version 2.1. The Bluetooth radio, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Česky [Czech] [Jmé no výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklæ rer herved, at fø lgende udstyr [udstyrets typebetegnelse] overholder de væ sentlige krav og ø vrige relevante krav i direktiv 1999/5/EF.
Magyar Alulírott, [gyá rtó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó [Hungarian] alapvetõ kö vetelmé nyeknek é s az 1999/5/EC irá nyelv egyé b elõ írá sainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs.
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之 無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機 設備之干擾。 Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2.
