Intermec Technologies Corporation EMC Test Lab DOC. NO.: 577-501-008 700 CDPD, FCC 2.
EXPEDITE WIRELESS IP MODEM HARDWARE INTERFACE SPECIFICATION OM - 01016529 Revision 3 NOVATEL WIRELESS TECHNOLOGIES LTD. Calgary, Alberta TITLE: Hardware Interface Specification for Expedite Wireless IP Modem DOCUMENT NO.: SHEET: REV: OM-01016529 1 of 17 3.
REVISION HISTORY REV# 1 2 3 ECO# 99007 99024 99047 EFF. DATE 990709 990809 NOVATEL WIRELESS TECHNOLOGIES LTD. Calgary, Alberta DESCRIPTION Initial release. Change order of pins 21 and 22 Add mounting instructions PREPARED P. Faubert P. Faubert K. Frayn APPROVED S. Smilar S. Smilar S. Smilar TITLE: Hardware Interface Specification for Expedite Wireless IP Modem DOCUMENT NO.: SHEET: REV: OM-01016529 2 of 17 3.
The information disclosed herein is the exclusive property of NOVATEL WIRELESS TECHNOLOGIES LTD. and is not to be disclosed without the written consent of NOVATEL WIRELESS TECHNOLOGIES LTD. No part of this publication may be reproduced or transmitted in any form or by any means including electronic storage, reproduction, execution or transmission without the prior written consent of NOVATEL WIRELESS TECHNOLOGIES LTD.
Table of Contents 1 WARNING ........................................................................................................................................ 6 2 INTRODUCTION.............................................................................................................................. 6 3 SCOPE............................................................................................................................................. 6 4 SPECIFICATIONS ...........................
.1 Shipping Packaging ................................................................................................................. 17 6.2 Labeling................................................................................................................................... 17 NOVATEL WIRELESS TECHNOLOGIES LTD. Calgary, Alberta TITLE: Hardware Interface Specification for Expedite Wireless IP Modem DOCUMENT NO.: SHEET: REV: OM-01016529 5 of 17 3.
1 WARNING All persons must be at least 20 cm from the antenna when transmitter operating to meet FCC RF exposure requirements. Refer to the Installation Instructions section for specific requirements for the antenna used with module. 2 INTRODUCTION This document describes the hardware interface for the Novatel Wireless Expedite Wireless IP Modem.
4.1.1 Data/Power Connection One connector is used to physically connect the power supply and 3.3 volt logic level host communication interface signals to the Expedite Wireless IP Modem. 4.1.1.1 Data/Power Connector Type Description: Samtec part number: 24-pin, 1.27 mm pitch, SMT, double row low profile socket type CLP-112-02-F-D Some interface connector options are provided here for reference. Contact Samtec for the latest connector mating options. NOVATEL WIRELESS TECHNOLOGIES LTD.
4.1.1.2 Surface Mount Mating Connector Options Description: 24-pin, 1.27 mm pitch, SMT, double row, zero profile, pin type header Samtec part number: DIS5-112-52-F-D-VS NOTE: This connector provides the lowest profile interface solution. Description: Samtec part number: 24-pin, 1.27 mm pitch, SMT, double row, low profile, pin type header FTS-112-03-F-DV 4.1.1.3 Through-Hole Mating Connector Options Description: Samtec part number: 24-pin, 1.
4.1.3 Pin Descriptions Pin # Name Direction 13, 14 Vcc1 POWER 15, 16 Vcc2 POWER 1,2 & 23,24 3 GND POWER PWR_IND OUTPUT 5 SM_IND OUTPUT 4 WKUP INPUT 6 DTM INPUT 7 DFM OUTPUT 11 RTS INPUT 10 CTS OUTPUT 8 DTR INPUT 9 DSR OUTPUT 12 GPIO1 17 GPIO2 18 GPIO3 19 GPIO4 20 GPIO5 21 GPIO6 22 ADC_IN BIDIRECTIONAL BIDIRECTIONAL BIDIRECTIONAL BIDIRECTIONAL BIDIRECTIONAL BIDIRECTIONAL ANALOG INPUT NOVATEL WIRELESS TECHNOLOGIES LTD.
4.2 Host Interface Specifications 4.2.1 Serial Data Rate and Format The Expedite supports asynchronous data transmission of the following rate and format: Baud Rate (bits/second) Data bits Parity Stop Bits 1200, 2400, 4800, 9600, 19200, 38400 7, 8 Even, None, Odd Mark 1, 2 4.3 Radio Specifications 4.3.1 Airlink Data Rate Rate - 19200 bits per second Error correction - Reed Solomon (63,47) Transmission standard (CDPD System Specification Part 401, Section 4.5.) 4.3.
(CDPD System Specification Version 1.1 part 409, paragraph 4.3) 4.4 Electrical Specifications 4.4.1.1 Operating Characteristics (Ta = 0º C to 60º C, VCC1 & VCC2 = 3.6V, unless otherwise noted.) SYMBOL VCC1 VCC2 ICC1 RESADC PARAMETER / CONDITIONS MODEM SUPPLY VOLTAGE RF POWER AMPLIFIER SUPPLY VOLTAGE MODEM OFF VCC1 = 3.6V SLEEP MODE VCC1 = 3.6V RECEIVE MODE VCC1 = 3.6V TRANSMIT MODE VCC1 = 3.6V MODEM OFF VCC2 = 3.6V SLEEP MODE VCC2 = 3.6V RECEIVE MODE VCC2 = 3.6V TRANSMIT MODE VCC2 = 3.
NOTE 2 - The WKUP pin is not connected directly to the CPU, it is connected though a resistor to the base of an NPN transistor. 4.5 Mechanical Specifications 4.5.1 Dimensions 5.00 mm x 54.00 mm x 72.91 mm 4.5.2 Weight Approximately: 27g 4.6 Environmental Specifications 4.6.1 Temperature Range The temperature is defined as per the CDPD System Specification Version 1.1 part 409, paragraph 5.2.
4.6.3 Shock Stability CDPD Part 409 paragraph 5.2.3.1 Half sine wave, 20g peak acceleration, 7 to 11 ms 3 impact on each of 6 faces 4.6.4 Vibration Stability CDPD Part 409 par. 5.2.3.2 (non-operational) Sinusoidal vibration at 1.5g acceleration swept through 5Hz to 500Hz, 0.1 octave/second 4.6.5 Regulatory compliance FCC title 47, parts 15 (class B) and 22. Resubmission is not required for the changes made in this product, including the changes made to name and part number. 4.6.
4.7 CDPD Part 409 Compliance The module will meet the CDPD System Specification Part 409, Small Form-Factor Devices. CDPD Part 409 7.1.2.2 7.1.2.3 7.2.3 Specification Parameter Condition Upper Limit RX sensitivity in AWGN (Note a: small form factor M-ES) RX sensitivity in Raleigh fading (Note b: small form factor M-ES) less than 5% block error rate -8 km/hr, 1% ber -50 km/hr, 1% ber -100 km/hr, 1% ber 8 us delay -111 dBm 7.5.
CDPD Part 409 Specification Parameter Condition Upper Limit Lower limit Watts) dB 5 INSTALLATION INSTRUCTIONS Unless the final product satisfies SAR (Specific Absorption Ratio) compliance through separate FCC approval, integration of this module into other products has some requirements which are outlined below. 5.1 Antenna Mounting The antenna must be mounted at a location such that no person(s) can come closer than 20 cm (7.9 inches) to the antenna when the transmitter is operating. 5.
5.5 Mounting Several methods are available for mounting the Expedite modem. The simplest for space constrained applications is a pressure fit. For applications where vibration is not an issue, double sided adhesive works well, although makes disassembly difficult. For applications where vibration is a concern, two mounting straps are available, a surface mount soldered version (Novatel part number 649496 00233 6) and a through – hole soldered version ( Novatel part number 649496 00232 9).
6 PACKAGING REQUIREMENTS 6.1 Shipping Packaging Packaging shall be appropriate for the shipping method. If the modem is to leave the ESD controlled environment, it should be packaged in an antistatic bag. 6.2 Labeling The modem labeling shall include: Product Label with FCC ID, country of origin, serial number, part number, and FCC compliance statement. NOVATEL WIRELESS TECHNOLOGIES LTD. Calgary, Alberta TITLE: Hardware Interface Specification for Expedite Wireless IP Modem DOCUMENT NO.
