70 Series Mobile Computer CK70, CK70NI, CK71, CK71NI, CN70, CN70NI, CN70e, CN70eNI User Manual
Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation.
Document Change Record This page records changes to this document. The document was originally released as Revision 001. Version Number Revision Letter Date 004 C 2/2012 Revised information on ScanNGo bar codes. 003 B 12/2011 Added information on: • the flashlight feature. • the Carrier Selection application. Revised information on: • the Intermec Settings menus. • upgrading the system software and the operating system. • GPS procedures. • ScanNGo bar codes.
iv 70 Series Mobile Computer User Manual
Contents Contents Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Global Services and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Read Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Insert a MicroSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Install a MicroSD Card in a CN70 or CN70e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Install a MicroSD Card in a CK70 or CK71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 Use the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 About the Color Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Take a Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Record a Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 7 Manage the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Manage the Computer in Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Manage the Computer Using SmartSystems Foundation . . . . . . . . . . . . . . . . . . . . 98 Manage the Computer Using Third-Party Software . . . . . . . . . . . . . . . . . . . . . . . . . 99 Develop and Install Applications . . . . . . . . . . . . .
Contents ASpecifications and Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Physical and Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 CN70 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 CN70e Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 CK70 Physical Dimensions . .
Contents x 70 Series Mobile Computer User Manual
Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety cautions.
Before You Begin Visit the Intermec technical knowledge base (Knowledge Central) at www.intermec.com and click Support > Knowledge Central to review technical information or to request technical support for your Intermec product. Send Feedback Your feedback is crucial to the continual improvement of our documentation. To provide feedback about this manual, please contact the Intermec Technical Communications department directly at TechnicalCommunications@intermec.com. Telephone Support In the U.S.A.
Before You Begin Who Should Read This Manual This manual is written for the person who is responsible for installing, configuring, and maintaining the 70 Series Mobile Computer. This manual provides you with information about the features of the 70 Series mobile computer, and how to install, configure, operate, maintain, and troubleshoot it. Before you work with the 70 Series mobile computer, you should be familiar with your network and general networking terms, such as IP address.
Before You Begin Patent Information Product is covered by one or more of the following patents: 4882476; 4894523; 4953113; 4961043; 4970379; 4988852; 5019699; 5021642; 5038024; 5081343; 5095197; 5144119; 5144121; 5182441; 5187355; 5187356; 5195183; 5216233; 5216550; 5195183; 5195183; 5218191; 5227614; 5233172; 5241488; 5243602; 5258606; 5278487; 5288985; 5308966; 5322991; 5331136; 5331580; 5342210; 5349678; 5359185; 5371858; 5373478; 5389770; 5397885; 5410141; 5414251; 5416463; 5442167; 5464972; 5468947; 5
1 About the Computer Features This chapter introduces the 70 Series Mobile Computers with Windows® Embedded Handheld operating system. Use this chapter to learn about the basic features and functions of each computer, as well as the available accessories for it.
Chapter 1 — About the Computer Features About the 70 Series Mobile Computers The ergonomically designed Intermec 70 Series Mobile Computers are built on the Microsoft Windows Embedded Handheld operating system. They are lightweight, easy-to-use, and run most software developed for the Windows Embedded platform, including standalone, client-server, and browser-based applications. The 70 Series family of computers consists of four different models: the CN70, CN70e, CK70 and CK71.
Chapter 1 — About the Computer Features CN70 Back View Imager Camera Speaker port Battery IrDa port CK70 Front View Cell phone speaker Good read LED Notification LED Battery status LED Scan button On/off button Microphone 70 Series Mobile Computer User Manual 3
Chapter 1 — About the Computer Features CK70 and CK71 Back View Imager Camera Imager Camera Left speaker port IrDA port Battery Left speaker port IrDA port Battery What’s New in This Release This version of the user manual contains these updates: • • • • • 4 Added information on the flashlight feature. For more information, see “Use the Flashlight” on page 27. Added information about switching network carriers using the Carrier Selection application.
Chapter 1 — About the Computer Features Overview of 70 Series Features The 70 Series includes these standard features: • • • • • • • • • • EA30 area imager that can read bar codes and capture images (CK71 only) Choice of EA30, EX25, or EV12 imagers Multi-processor architecture with 512 MB DRAM and 1G Flash CDMA, UMTS, or Flexible Network Radio capability (not available on CK71) 802.
Chapter 1 — About the Computer Features About the Status LEDs Use the following illustrations and table to understand the status LEDs on your computer. All six status LEDS are not available on every 70 Series computer. For example, the QWERTY versions of the CN70 and CN70e do not have a Green key status LED.
Chapter 1 — About the Computer Features Location of the CK70 Status LEDs Notification LED Good Read and Ready-to-Work status LED Orange key status LED Battery status LED Green key status LED Shift key status LED (CK70 alphanumeric and CK71 function numeric) Shift key status LED (CK70 numeric and CK71 alphanumeric) Status LED Descriptions LED Color Description Notification Amber This LED is user-programmable. Good Read Green The computer successfully decoded a bar code.
Chapter 1 — About the Computer Features LED Color Description Key Status Green The Green function key is enabled. Orange The Orange function key is enabled. Red The Shift key is enabled. Shift 70 Series Accessories The 70 Series computer ships with a battery. All other accessories are sold and ordered separately. For help, contact your local Intermec sales representative.
Chapter 1 — About the Computer Features Accessory Description DX2 Dual Dock and DX4 Quad Dock. The DX2 and DX4 are available in charge-only and Ethernet configurations. Use these charger bases with the: • Computer cup to charge batteries while they are installed in the computer. • Battery cup to charge two batteries. Ethernet Snap-On Adapter Use the Ethernet adapter to be able to connect the computer to an Ethernet network.
Chapter 1 — About the Computer Features About Language Provisioning If your 70 Series computer includes language provisioning, you are prompted to select a language provision when the computer starts for the first time. It may take up to 15 minutes to load your language. Make sure you select the correct language before you tap Provision. If you need to have the language provisioning changed, you will need to send your computer to an Intermec Global Repair Center.
Chapter 1 — About the Computer Features Change the Battery If your battery power is low, you need to either charge the battery in the computer, or replace it with a charged battery. 1 Save your files and close any open applications. 2 Press the Power button and choose Hibernate from the menu to suspend the computer. 3 Detach the handstrap from the computer.
Chapter 1 — About the Computer Features 4 Make sure the computer is in hibernate mode and that the screen has turned off. 5 Remove the battery. 12 • On the CN70 or CN70e, push the battery release toward the bottom of the computer until the battery releases and then lift it away from the computer. • On the CK70 or CK71, push the battery release toward the top of the computer until the battery releases and then lift it away from the computer.
Chapter 1 — About the Computer Features 6 Insert the top end of a fully charged battery into the computer, and press down firmly on the bottom of the battery. Make sure that the battery release is fully engaged. About Battery Status Use the battery icon on the Title bar to see the power status of your battery. If you want more detailed information on your battery such as usage time or voltage, use the Intermec Dashboard.
Chapter 1 — About the Computer Features Understanding the Battery Status LED LED State Description Steady green The computer is connected to a charger and the battery is more than 95% charged. Blinking red The battery is very low. The computer will soon go into Suspend mode. Charge or replace the battery. Steady red The computer is connected to a charger and the battery is charging. Blinking red-amber The battery charging system has encountered an error. The battery is not charging.
Chapter 1 — About the Computer Features When You Want To: Do This to Save Battery Power: Store the computer for more than If you are storing the computer for a few a day. days, like over the weekend, install a charged battery or connect the computer to a power source. If you are storing the computer for longer, remove and charge the battery, and then store both the battery and computer in a cool location. If you store the battery for several months, recharge the battery to keep it at peak performance.
Chapter 1 — About the Computer Features CN70 Numeric Keypad Esc 1 Caps 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ 0 Space Enter CN70e QWERTY Numeric Keypad 16 70 Series Mobile Computer User Manual
Chapter 1 — About the Computer Features CN70e Calculator-Style Numeric Keypad CN70e Numeric Keypad 70 Series Mobile Computer User Manual 17
Chapter 1 — About the Computer Features The CK70 comes with either a large alpha or an alphanumeric keypad. The CK71 comes with either a numeric function keypad or an alphanumeric keypad. The computer has an ambient light sensor that detects low light and turns on the keypad backlight. By default, the keypad backlight is enabled in low light conditions. You can disable the keypad backlight to conserve power. Use Intermec Settings to configure the backlight.
Chapter 1 — About the Computer Features CK70 Alphanumeric Keypad Esc Alt F6 Send 1 F1 F7 End 2 3 Insert F2 Delete 4 5 6 7 8 9 F8 F3 F9 0 F4 Enter F10 F5 F11 A F17 G F23 Ctrl F12 B F18 H F13 C F19 Space F14 D F20 F15 E F21 F16 F F22 I J K L F24 M N O P Q R S T U V W X Y Z 70 Series Mobile Computer User Manual 19
Chapter 1 — About the Computer Features CK71 Numeric Function Keypad View Insert Fld- Fld+ View SysRq Return Page Fld Exit Enter A PrvScr B 7 D Delete PA1 Roll 9 F 5 H 1 Home C NxtScr 8 E 4 G Roll PA2 Attn I Esc PA3 3 Space K Return 0 L F13 F1 P F17 F5 T F21 F9 M F14 Enter N F2 Q F18 F22 F16 F4 F19 F7 V O S F20 F8 F23 W F24 F10 F11 F12 X Y Ctrl 20 F15 F3 R F6 U Reset 6 2 J Clear Z Alt 70 Series Mobile Computer User Manual
Chapter 1 — About the Computer Features CK71 Alphanumeric Keypad View Alt Reset Page Fld Exit Esc F6 PA1 PrvScr 7 F1 4 F2 Roll Delete 9 5 6 2 3 F9 Autolog Return 0 F4 Enter F10 EEOF F5 F11 Attn A Ctrl F12 B F13 C Space F14 Dup F15 Erase F16 Find D E F17 FldMk F18 Home F19 Hex F20 G Clear Help Fld+ 1 F3 NxtScr 8 F7 PA2 Insert F8 PA3 Fld- Roll H I F23 Menu F24 NewLn Mode J K L Print SysRq Remove Q R W X M N O P S T U V ? Y 70 Series Mobile Com
Chapter 1 — About the Computer Features Enter Characters on the QWERTY Keypad You need to use the orange modifier key b and the Shift key y to access all characters and functions on the QWERTY keypad. To type a character: • Press the key for that character. To type a character or access a function on the overlay: • Press b and then press the key for the character or function.
Chapter 1 — About the Computer Features • To type “C,” press c 1 and then press c 2 2 2. Note: On the calculator-style keypad, the 2 is replaced by the 8. To only type letters: Press c c to lock the green modifier key, and then press the key one to four times depending on the position of the letter. While the green modifier key is locked, press 1 to toggle between only uppercase and lowercase letters. • To unlock the green modifier key, press c.
Chapter 1 — About the Computer Features About the Power Button When you press the Power button, a dialog appears with a list of power options. If you do not select a power options setting, the currently selected action (the button outlined in bold) occurs after the timeout. The Intermec Power Options Default Screen Use the following table to understand the Intermec Power Options.
Chapter 1 — About the Computer Features Option Description Suspend Medium power saving mode. The computer powers off all radios and internal devices not involved in saving the system state, but the phone stays on to receive calls. This option is the default setting. You can wake the computer by pressing the Power button, pulling the scanner trigger, receiving a call, scheduling an event such as an alarm, or by connecting external power.
Chapter 1 — About the Computer Features Configure the Screen Backlight The display has an ambient light sensor that automatically adjusts the backlight intensity to conserve power and ensure the display is readable. By default, the screen turns off when there is no activity with the computer. Press a key or tap the screen to resume activity. You can configure the screen backlight to turn off. 1 Tap Start > Settings > Power. 2 Tap Advanced on the horizontal scroll bar.
Chapter 1 — About the Computer Features You can adjust the volume settings using Intermec Settings or the horizontal scroll menu. 1 Tap the Volume icon at the top of the screen, and then tap the volume icon on the horizontal scroll menu. 2 Use your stylus or the u and d keys to adjust the volume slider to the volume you want, select Vibrate, or select Off. Use the Imager The computer ships with an internal imager. You can use the imager as a flashlight or to read bar codes.
Chapter 1 — About the Computer Features Read Bar Codes Depending on the imager model in your computer, you can read 1D and 2D bar code symbologies, composite symbologies, and postal codes. 1 Enable only the bar code symbologies that you need. 2 Use Intermec Settings to choose the predefined imager mode that best suits your environment: Predefined Mode For Scanning 1D Only 1D labels. 1D and 2D Standard (Default) All types of bar code labels.
Chapter 1 — About the Computer Features 5 Use the laser pointer as a guide and aim toward the middle of the bar code. Make sure that the illumination beam or frame covers the bar code you are trying to decode. When the computer successfully reads a bar code label, you hear a high beep, and the Good Read LED turns on briefly. 6 Release the Scan button. You can also connect the computer to: • • cordless scanners, such as the SF51 and SR61 through Bluetooth communications.
Chapter 1 — About the Computer Features 3 Remove the two Phillips screws and open the card access door. 4 Slide the SIM card door to the left to unlock it and open the door.
Chapter 1 — About the Computer Features 5 Slide the microSD card door towards the top of the computer to unlock it and open the door. 6 Slide the microSD card into place. 7 Close the microSD card door and slide it towards the bottom of the computer to lock it in place. 8 Close the SIM card door and slide it to the right to lock it in place. 9 Close the card access door and replace the two screws. 10 Install the battery.
Chapter 1 — About the Computer Features 11 Reattach the handstrap. 12 Press the Power button. The computer cold boots. Install a MicroSD Card in a CK70 or CK71 1 Press the Power button to turn off the computer. 2 Remove the handstrap. 3 Remove the two screws that attach the interface adapter cover to the back of the computer.
Chapter 1 — About the Computer Features 4 Slide the SIM card door to the left to unlock it and open the door. 5 Slide the microSD card door towards the top of the computer to unlock it and open the door.
Chapter 1 — About the Computer Features 6 Slide the microSD card into place. 7 Close the microSD card door and slide it towards the bottom of the computer to lock it in place. 8 Close the SIM card door and slide it to the right to lock it in place. 9 Replace the interface adapter cover and attach with the two screws removed in Step 2. 10 Install the battery. Press down firmly on the bottom of the battery, and make sure that the battery release tab is fully engaged. 11 Reattach the handstrap.
Chapter 1 — About the Computer Features Use Microsoft ActiveSync to Transfer Files You can use Microsoft ActiveSync (Windows XP or earlier) or Windows Mobile Device Center (Windows Vista or Windows 7) to establish a connection between your computer and a PC. After you connect to your PC, you can transfer files, synchronize files, remotely debug, and perform other device management activities. ActiveSync and Windows Mobile Device Center are free applications available from the Microsoft website at www.
Chapter 1 — About the Computer Features Use the Computer as a Mass Storage Device You can connect the 70 Series computer as a mass storage device to your desktop PC. When connected as a mass storage device, you can easily copy files to and from the mobile computer. 1 Go to www.datalight.com and download the Reliance Nitro Windows Driver (RNWD). You will need to login before you can download the driver. 2 Connect the mobile computer to your desktop PC using a USB cable.
2 About the User Interface and Intermec Applications Use this chapter to learn about the Windows Embedded Handheld user interface and how to interact with the screen. You can also use this chapter to learn about the Intermec applications on your computer, as well as additional Intermec applications you can download.
Chapter 2 — About the User Interface and Intermec Applications About the User Interface The user interface for the Windows Embedded Handheld 6.5 operating system is different from previous versions of Windows Mobile. The interface is touch-friendly and easy to navigate. Use the following sections to understand how to interact with Windows Embedded Handheld 6.5. About the Home Screen When you turn on your mobile computer, the Home screen is the first screen that appears.
Chapter 2 — About the User Interface and Intermec Applications The horizontal scroll bar also replaces tabs within Windows screens and allows for easier navigation. Clock & Alarms Screen With Horizontal Scroll Bar Use the Tile bar to navigate between screens and within applications. The icons available on the Tile bar change depending on the application you are using. Interact With the Screen The Windows Embedded Handheld 6.
Chapter 2 — About the User Interface and Intermec Applications Title Bar Status Icons Tappable icons in the Title bar immediately show you the status of your network, your phone, the volume, the battery, and the time. Use the following table to understand what the icons mean. Title Bar Status Icon Descriptions Icon Description You have a new notification. You have a new text message. You have a new email message. You have a new instant message. You missed a call. The speakerphone is on.
Chapter 2 — About the User Interface and Intermec Applications Icon Description A UMTS network is available. Connecting to a UMTS network. A UMTS connection is active. A 3G+ network is available. An EDGE network is available. Connecting to an EDGE network. An EDGE connection is active. A GPRS network is available. Connecting to a GPRS network. A GPRS connection is active. An HSDPA network is available. Connecting to an HSDPA network. An HSDPA connection is active. Bluetooth is on.
Chapter 2 — About the User Interface and Intermec Applications Icon Description Connected to a wireless network, and other networks are detected. Information about a new wireless network is available. A network connection is active. A network connection is inactive. The phone has maximum signal strength. The phone has no signal. The phone capability is off. The phone has no service. The phone is searching for service. Data is being transferred. A voice call is in progress. A voice call is on hold.
Chapter 2 — About the User Interface and Intermec Applications Icon Description The battery has a low charge. The battery has a very low charge. The battery is attached to external power and is charging. No battery is installed in the computer. Call forwarding is on. Voice mail is off. GPS locator is off. GPS locator is on. Align the Screen You may need to align your screen if you tap on one area and it registers in a different part of the screen.
Chapter 2 — About the User Interface and Intermec Applications Intermec Applications Available on the Mobile Computer Icon Application Description Bluetooth Audio Use the Bluetooth Audio application to connect to a Bluetooth headset or hands-free device. For more information, see “Connect to a Bluetooth Audio Device” on page 81. Carrier Selection Use the Carrier Selection application to quickly change your network carrier. For more information, see “About Switching Network Carriers” on page 54.
Chapter 2 — About the User Interface and Intermec Applications Icon Application Description Wireless Center Use the Wireless Center to turn radios (Wi-Fi, Bluetooth, phone) on and off and configure settings for each radio. Wireless Printing Use the Wireless Printing application to connect to a Bluetooth printer. For more information, see “Connect to a Bluetooth Printer” on page 80. Wireless Scanning Use the Wireless Scanning application to connect to a Bluetooth scanner.
Chapter 2 — About the User Interface and Intermec Applications About Image Capture The Intermec Image Capture application is provided for use on the 70 Series computers with an EA30 imager. Image capture provides a way for users to capture a high quality grayscale image with a mobile computer. Image Capture also allows you to change settings to provide the best image possible for the conditions present. You do not need to license Image Capture.
Chapter 2 — About the User Interface and Intermec Applications About Intermec Terminal Emulator (ITE) Intermec Terminal Emulator (ITE), part of Intermec Client Pack (ICP), is the next generation of Intermec’s popular terminal emulation client designed for enterprise-level data collection. It provides a consistent user interface and a common menu structure to simplify the use and management of applications running on Intermec mobile and wireless computers.
Chapter 2 — About the User Interface and Intermec Applications 48 70 Series Mobile Computer User Manual
3 Use the Phone You can use the phone feature to make and receive telephone calls, as well as transmit data through cellular wide-area networks (WANs).
Chapter 3 — Use the Phone About the Phone The 70 Series mobile computer supports two types of cellular technology: • CDMA • UMTS Note: Your Flexible Network Radio mobile computer supports both CDMA and UMTS technology. Your Flexible Network Radio does not support Network Information and Time Zone (NITZ) messages to automatically set the system time. Phone features on the computer include a speaker and a microphone. You can also use a Bluetooth headset or hands-free kit.
Chapter 3 — Use the Phone 2 On the CN70 or CN70e: a Push the battery release tab forward until the battery releases, and lift the battery away from the computer. b Remove the two Phillips screws and open the card access door. 3 On the CK70, remove the two screws and lift the card access door away from the computer. 4 Slide the SIM card door to the left to unlock it and open the door.
Chapter 3 — Use the Phone 5 Slide the SIM card into the slot in the card access door. 6 Close the SIM card door and slide it to the right to lock it in place. 7 Close the card access door and replace the two screws. 8 Install the battery. Press down firmly on the bottom of the battery, and make sure that the battery release tab is fully engaged. 9 Press the Power button. The computer cold boots.
Chapter 3 — Use the Phone on the outside of the computer shipping box. in the Version Information menu. Tap Start > Settings > Personal > Phone > Version Information tab. The activation process is slightly different for each CDMA carrier. Your carrier sales contact and an Intermec representative can guide you through the process. • • After you supply the MEID to your carrier, they will respond with values that you must enter using the Windows Mobile Activation Wizard (if required).
Chapter 3 — Use the Phone Turn the Phone On and Off Before you can start using your phone, you need to enable it. You can use Wireless Center to enable and disable your phone, as well as Bluetooth and Wi-Fi communications. 1 Tap Start > Settings > Connections > Wireless Center. 2 Tap Phone to turn on the Phone 3 (Optional) To configure the phone, tap Menu in the tile bar at the bottom of the screen. 4 Tap OK when you are done configuring the options. 5 Tap OK to close Wireless Center.
Chapter 3 — Use the Phone Your UMTS connection entry can be automatically built from your carrier issued SIM card. To automatically recreate your network connection, install your SIM card and tap Start > Settings > Connections > Connections > Tasks tab > Automatically configure connection. Switch Network Carriers Use the Carrier Selection application to quickly change your WWAN radio network carrier on your Flexible Network Radio-enabled CN70, CN70e, or CK70 mobile computer.
Chapter 3 — Use the Phone 3 Enter a Connection Name. In the Phone Number field, enter #777 and tap OK. The Manage WWAN Radio State screen appears. 4 From Active Connection, select your Connection Name and Connect Now and tap OK.
Chapter 3 — Use the Phone Make a Phone Call After you activate your UTMS or CDMA phone, you are ready to start making phone calls. Note: Your Flexible Network Radio mobile computer is data only. You cannot make phone calls from the Flexible Network Radio. 1 Press Phone. 2 Tap the keys to enter the telephone number you want to call, and tap Talk. Make an Emergency Phone Call You can use the UMTS phone to make an emergency phone call even if the SIM card is missing.
Chapter 3 — Use the Phone 58 70 Series Mobile Computer User Manual
4 Use the Camera You can use the color camera to take pictures and record videos.
Chapter 4 — Use the Camera About the Color Camera The camera and flash are located on the back of the computer. You run the Pictures & Videos application to access the camera features. In this application, you can: take, view, and edit pictures. record and launch video clips stored on the computer or a microSD card. • configure camera options. You can also send pictures and video clips to others or save an image as the background on the Home screen.
Chapter 4 — Use the Camera Record a Video You need to switch to video mode to record video. When you record video, the video is saved as an .mp4 file and stored in the /My Documents/My Pictures folder. 1 Tap Start > Pictures & Videos. 2 Tap the Camera icon in the grid or the Camera button on the Tile bar, or press Enter. 3 Tap Menu > Video. 4 Using the screen as a viewfinder, move the video camera until you see the scene you want to video record. 5 Press Enter to start recording.
Chapter 4 — Use the Camera 62 70 Series Mobile Computer User Manual
5 Use GPS The 70 Series computer comes equipped with an integrated Global Positioning System (GPS) receiver if your computer has phone capability (WWAN radio). The GPS receiver can deliver standards-based National Marine Electronics Association (NMEA) data strings to GPS applications.
Chapter 5 — Use GPS About the Integrated GPS on Your Computer Intermec recommends that you use the GPS Intermediate Driver (GPSID) instead of directly accessing the GPS hardware. The GPSID is a Microsoft software component that interacts between applications and the GPS hardware. As a Microsoft software component, the GPSID: • • allows multiple applications to simultaneously access the GPS data stream. provides access to GPS data without requiring applications to recognize and parse NMEA syntax.
Chapter 5 — Use GPS 3 Tap Access in the horizontal scroll bar and select the Manage GPS automatically check box. 4 Tap OK. Improve GPS Performance on the Computer Use the iGPS application to improve the performance of the GPS on your CN70, CN70e, or CK70 computer. The integrated GPS module has three operating modes: • Standalone • MS Assisted (Mobile Station Assisted) • gpsOneXTRA™ (UMTS computers only) In Standalone mode, the GPS module relies solely on GPS satellites to determine position.
Chapter 5 — Use GPS Qualcomm’s gpsOneXTRA Assistance technology provides enhanced operation for Standalone GPS. This option enables the UMTS-enabled computer to automatically download a small assistance data file from the XTRA servers through a brief internet access session. To use this option, you must have a valid and activated WAN data connection. Note: Internet connection fees may apply. Another option you can configure with iGPS is the fix interval.
6 Configure the Computer Use this chapter to learn about the available methods for configuring your mobile computer and how to use Intermec Settings. You can also use this chapter to learn how to configure network communications and wireless security.
Chapter 6 — Configure the Computer How to Configure the Computer You can configure many parameters on the computer such as the bar code symbologies it decodes or the network settings. The values you set for these parameters determine how the computer operates. There are several ways to configure the computer: • Directly on the computer. You can use Intermec Settings directly on the computer to change only the settings on that computer.
Chapter 6 — Configure the Computer Start Intermec Settings Intermec Settings is located on the System screen. • Tap Start > Settings > System > Intermec Settings. The Intermec Settings Main Menu appears. About the Structure of Intermec Settings Use the tables below to help find the parameters in Intermec Settings that you want to configure. Each table contains the parameters for one of the Intermec Settings Main Menu options.
Chapter 6 — Configure the Computer Data Collection Menu Data Collection Options Parameters You Can Configure Internal Scanner • • • • • • • • • • • • • • • • • Bluetooth Scanner Dock Tethered Scanner Camera Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Scanner port settings Imager settings Decode security Symbologies Scanner settings Camera settings Decode security BT-Configure on Connect Bluet
Chapter 6 — Configure the Computer Communications Options Parameters You Can Configure WWAN Radio • • • • • Serial Port Switch Serial port switch settings (IrDA, docking connector, and back interface) Add WWAN connection Edit WWAN connections Manage WWAN radio Carrier Selection WWAN information Device Settings Menu Device Settings Options Parameters You Can Configure Date and Time Date and time settings Good Read • • • • • • • • Sounds Internal scanner Tethered scanner Bluetooth scanner Beeper
Chapter 6 — Configure the Computer Device Settings Options Parameters You Can Configure Profile Settings Application Whether these parameter options appear in Profile Settings: • Camera • Power • Scanning Features Disabled by Policy None (read-only) Printer Menu Printer Options Parameters You Can Configure Printer (if connected through Bluetooth) Printer settings (Auto detect printer, memory, display, and so on) Note: The Printer menu displays settings for Bluetooth connected printers.
Chapter 6 — Configure the Computer Virtual Wedge Menu Virtual Wedge Options Parameters You Can Configure Enable Virtual Wedge Enable virtual wedge Bar Code Scanner Wedge Bar code scanner wedge settings (bar code scanner grid and label encoding) Magstripe Reader Wedge Magstripe Reader Grid Core Messaging Service Menu Core Messaging Service Options Parameters You Can Configure Server IP Server IP (read-only) Associated Server IP Associated server IP Broadcast Name Broadcast name Port Port (r
Chapter 6 — Configure the Computer Location Services Menu Location Services Options Parameters You Can Configure Server Server settings (port and enable server) Virtual GPS Virtual GPS settings For more information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual. Navigate in Intermec Settings You can easily navigate through the screens in Intermec Settings to find the parameter you need to configure.
Chapter 6 — Configure the Computer 3 From the Camera, Power, or Scanning submenu, check or clear the Display check box for the settings you want to have available to the end user. 4 Click OK to save your selection. Restore Default Settings You can easily restore a menu to its default settings or all of the Intermec Settings parameters to their default settings if necessary. 1 Navigate to the menu that you want to restore to defaults. 2 Tap Menu > Restore Menu Defaults.
Chapter 6 — Configure the Computer Use Intermec Settings Remotely With SmartSystems Foundation Your mobile computer is SmartSystems-enabled, which lets you open Intermec Settings from the SmartSystems console to remotely configure all of your mobile computers. For more information on SmartSystems, see “Manage the Computer Using SmartSystems Foundation” on page 98. 1 In the SmartSystems console, select a mobile computer and right-click. 2 From the menu, select Intermec Settings.
Chapter 6 — Configure the Computer The mobile computer contains an 802.11 radio to transfer data using wireless communications and to support the TCP/IP network protocols. This section of the manual assumes that your wireless network is set up, including your access points. By default, the 802.11 radio is disabled. Use the following procedure to enable the Wi-Fi radio using Intermec Settings.
Chapter 6 — Configure the Computer Configure Bluetooth Communications Your mobile computer is Bluetooth™-enabled, which lets you connect to other Bluetooth devices, such as scanners, printers, or audio devices. You need to turn on the Bluetooth radio before you can discover and connect to other Bluetooth devices. By default, the radio is turned off. You can configure Bluetooth communications using Intermec Settings or from the Start menu. 1 Tap Start > Settings > Bluetooth > Mode.
Chapter 6 — Configure the Computer 1 Tap Start > Settings > System > Wireless Scanning. 2 Tap Add Device. 3 Select Quick Connect, Search, or Manual. Follow the onscreen instruction to add a wireless scanner.
Chapter 6 — Configure the Computer Connect to a Bluetooth Printer To configure your computer for Bluetooth wireless printing, you need to: • • create an application that opens the wireless printing COM port on your computer. For help, see the Bluetooth Resource Kit, which is part of the Intermec Developer Library (IDL), available from the Intermec website at www.intermec.com/idl. select the current wireless printer on your computer. For help, see the next procedure.
Chapter 6 — Configure the Computer Connect to a Bluetooth Audio Device Use the Bluetooth Audio enabler to discover, activate, and connect to Bluetooth audio devices such as a headset. This enables system sounds to be monitored through the headset. 1 Tap Start > Settings > System > Bluetooth Audio. 2 Tap Search to find your Bluetooth headset or hands-free device. 3 Select your device from the list and configure any settings. 4 Click OK when you are done.
Chapter 6 — Configure the Computer Connect to a Tethered Scanner Use this procedure to connect your mobile computer to an SR30, SR61T, or ASCII tethered scanner and enable RS-232 communications. 1 Tap Start > Settings > System > Intermec Settings > Communications > Serial Port Switch. 2 Select Standard docking and IrDA and tap OK. If the serial port switch is set to one of the other options, you need to select Standard docking and IrDA and then save and reboot the computer before you proceed.
Chapter 6 — Configure the Computer 3 Enter a name for the connection, such as “ISP Connection.” 4 If you are using an external modem connected to your mobile computer with a cable, select Hayes Compatible on COM1 from the Select a modem list. 5 Tap Next. 6 Enter the access phone number and then tap Next. 7 Enter the User name, Password, and Domain (if provided by an ISP or your network administrator). 8 Tap Finish. 9 On the Connections screen, tap Advanced on the horizontal scroll. 10 Tap Dialing Rules.
Chapter 6 — Configure the Computer Create a VPN Server Connection You can create a Virtual Private Network (VPN) connection to securely connect to servers, such as a corporate network, through the Internet. Before you can create a VPN connection, you need this information from your network administrator: • User name • Password • Domain name • TCP/IP settings • Host name or IP address of the VPN server After you have located this information, you can create a VPN server connection.
Chapter 6 — Configure the Computer About Wireless Security The computer provides five types of security for your wireless network: • Wi-Fi Protected Access 2 (WPA2™) • Wi-Fi Protected Access (WPA) • • 802.1x LEAP • WEP This section explains how to configure wireless security on your mobile computer. Intermec recommends that you implement WPA2 security using PSK (Personal) or 802.1X (Enterprise) key management as appropriate.
Chapter 6 — Configure the Computer • If you are primarily using the computer to connect to Wi-Fi hotspots, you may want to use Microsoft security. To use Microsoft security, you need to select it as your security choice. For help, see “Select Microsoft as Your Security Choice” on page 90. Select a Funk Security Profile You can define up to four profiles for Funk security. Different profiles let your computer communicate in different networks without having to change all of your security settings.
Chapter 6 — Configure the Computer 5 Select the profile you want to configure. 6 For Association, choose WPA or WPA2. Encryption automatically defaults to TKIP or AES, respectively. 7 For 8021x, choose TTLS, PEAP, EAP-FAST, or TLS. 8 If you choose TTLS, EAP-FAST, or PEAP: a For Prompt for Credentials, choose Enter credentials now. b Enter a User Name and User Password. c For Validate Server Certificate, choose Yes.
Chapter 6 — Configure the Computer the access point. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the 70 Series internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 9 Save your settings. Configure 802.1x Security With Funk Security Use the following procedure to configure 802.1x-WEP security with Funk security. Intermec recommends that you use WPA2-802.1x instead of 802.1x-WEP if possible.
Chapter 6 — Configure the Computer Configure LEAP Security With Funk After you configure the communications and radio parameters on your mobile computer and select Funk as your security choice, you can configure LEAP. 1 Start Intermec Settings. 2 Choose Communications > 802.11 Radio > Funk. 3 Select the profile you want to configure. 4 For 8021x, choose LEAP. 5 For Association, choose Open, WPA, WPA2, or Network EAP.
Chapter 6 — Configure the Computer 9 Define a value for the keys you want to use. You can define up to four keys (Key 1 through Key 4). Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for 128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs. 10 For Transmit key, choose the key you want to use for transmitting data. 11 Save your settings.
Chapter 6 — Configure the Computer Select Microsoft Security Use the following procedure to select Microsoft security. 1 Start Intermec Settings. For help, see “Configure the Computer” on page 67. 2 Choose Communications > 802.11 Radio > Security Choice. 3 From the Security Choice list, select Microsoft Security. An alert box appears telling you that you must save your settings and reboot the computer for the new security choice to take effect. 4 Choose Yes.
Chapter 6 — Configure the Computer f Press OK to save the Microsoft Security settings. 8 If you choose PEAP: a Load a root certificate of the authentication server on your computer. For help, see “Load a Certificate” on page 95. b Press OK to save the security settings and the User Logon dialog box appears. c Enter a User Name, Password, and Domain. Select Save Password if you want to save the password for future authentication sessions. d Press OK to save the Microsoft Security settings.
Chapter 6 — Configure the Computer Configure 802.1x Security with Microsoft Use the following procedure to configure 802.1x security with Microsoft security. Intermec recommends that you use WPA2-802.1x instead of 802.1x-WEP if possible. 1 Make sure the communications and radio parameters on your computer are configured. 2 Start Intermec Settings. 3 Choose Communications > 802.11 Radio > Microsoft Security. 4 For Infrastructure Mode, choose Infrastructure. 5 For Network Authentication, choose Open.
Chapter 6 — Configure the Computer 10 For Network Key Setting, choose Automatic. 11 Save your settings. Configure Static WEP Security With Microsoft Use the following procedure to configure static WEP security with Microsoft security. Intermec recommends that you use WPA2-PSK instead of WEP if possible. 1 Make sure the communications and radio parameters on your computer are configured. 2 Start Intermec Settings. 3 Choose Communications > 802.11 Radio > Microsoft Security.
Chapter 6 — Configure the Computer Load a Certificate To use transport layer security (TLS) with WPA or 802.1x security, you need a unique client certificate on the computer and a trusted root certificate authority (CA) certificate. Certificates are pieces of cryptographic data that guarantee a public key is associated with a private key. They contain a public key and the entity name that owns the key. Each certificate is issued by a certificate authority. 1 Start Intermec Settings.
Chapter 6 — Configure the Computer b Tap Web Enrollment. c Enter the User, Password, and Server (IP address) to log into the server. d Tap OK. A dialog box appears asking if you want to load the root certificate. e Tap OK. The Enrollment Tool message box appears telling you that the certificate has been added. f 96 Tap OK to close the message box.
7 Manage the Computer Use this chapter to learn how to remotely update, configure, and monitor your Intermec mobile computers. You will also find information on installing and developing software applications as well as how to upgrade the system software.
Chapter 7 — Manage the Computer Manage the Computer in Your Network When you have multiple mobile computers and peripherals in your network, it is essential to have an easy way to manage updates, configure all of the devices, and remotely troubleshoot problems. Intermec provides a free device management software platform called SmartSystems™ Foundation to help you manage your devices. You can also purchase third-party device management software through a vendor.
Chapter 7 — Manage the Computer save configuration settings from a single device and deploy those settings to many devices simultaneously. • remotely change settings on SmartSystems-enabled computers and peripherals. The SmartSystems Foundation console can report on asset locations and battery status, making it easier to manage your mobile devices. • With a Provisioning license, SmartSystems Foundation can automatically push software, configuration settings, and other files to connected mobile computers.
Chapter 7 — Manage the Computer Package Your Application For very simple applications, the executable file may be the only file you need to deploy. More typically, you will have a set of files to install. Intermec recommends using .cab files to install your applications. The computer uses standard Windows Mobile .cab files and will install third-party .cab files. Choose a Target Location You can have your .
Chapter 7 — Manage the Computer 2 Double-click the application file to install it. The application file should appear in the Software Vault. 3 From the SmartSystems console in the Software Vault, drag-and-drop the application onto each mobile computer in your network, or drop the application on a group of computers contained in a folder. Install Applications Using Microsoft ActiveSync When you only have a few computers to update with applications, you can copy files using Microsoft ActiveSync.
Chapter 7 — Manage the Computer At boot time, AutoRun executes any commands found in its data file, Autouser.dat. For more information on how to use the AutoRun.exe feature, view the Readme.txt file located in the My Device\Flash File Store\2577 directory on your computer. Update the System Software The mobile computer uses SmartSystems bundles to update the operating system (OS) and the system software.
Chapter 7 — Manage the Computer 4 Download the SmartSystems bundle to your PC. 5 Double-click the SmartSystems bundle on your PC to extract the update files to the software vault. 6 From the SmartSystems console, locate the bundle to install and drag them to each mobile computer (or group in a folder) you want to update. The SmartSystems console installs the update on your mobile computers.
Chapter 7 — Manage the Computer 3 Transfer the autoflash.img file into the root directory of the microSD card. 4 Turn off your mobile computer and install the microSD card in your mobile computer. For help, see “Insert a MicroSD Card” on page 29. 5 Turn on your mobile computer. The update process begins. Your mobile computer may restart several times during this process. When the update is complete, the Autoflash Complete message appears. 6 Remove the microSD card.
8 Troubleshoot and Maintain the Computer If you encounter any problems while using the 70 Series computer, look in this chapter to find a possible solution. You will also find information on routine maintenance.
Chapter 8 — Troubleshoot and Maintain the Computer About the Intermec Dashboard The Intermec Dashboard is designed to provide proactive monitoring of your mobile computers to prevent downtime. You can easily see the health of the device and can help pinpoint the source of a problem to determine if it is hardware or software related. Intermec Dashboard displays information such as the status of network connections, battery usage, storage space, and internal devices.
Chapter 8 — Troubleshoot and Maintain the Computer Troubleshoot Your Mobile Computer Use the troubleshooting tables in this section to fix problems with the Wi-Fi connection, 802.1x security, the imager, or general problems with operating the mobile computer. If you send the computer in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution A network connection icon appears in the The computer may not be communicating with the toolbar, but then disappears. intended access point. Make sure the network name matches the access point network name. Default network name is “INTERMEC.” The access point may not be communicating with the server. Ensure the access point is turned on, properly configured, and has 802.1x security enabled. Troubleshoot 802.
Chapter 8 — Troubleshoot and Maintain the Computer Check 802.11 Network Status If you have trouble connecting to your 802.11 wireless network: Make sure you have correctly set network parameters on the computer. • Check your wireless security settings. Follow the next procedure to verify available access points and networks, check signal strength, and view other diagnostics.
Chapter 8 — Troubleshoot and Maintain the Computer c Tap Ping. The graph shows the amount of time it takes for the host to return the ping. Tap List to see this information in a list format. 5 Tap the RSSI tab to view the received signal strength of the host signal. The information box includes the current signal strength, host SSID name, MAC address, data rate, and transmit power. • Tap Mark to place an arrow marker above the graph. 6 Tap the Conf tab to set up a log file that lists RSSI history.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution When you release a Scan button The Good Read light will remain on if you configure the or handle trigger, the Good Read computer to use continuous/edge triggering. If you configure light does not turn off. the computer for level triggering and the Good Read light remains on, there may be a problem. Press one of the Scan buttons or pull the trigger again without scanning a bar code label.
Chapter 8 — Troubleshoot and Maintain the Computer Use ScanDiagnostic to Troubleshoot the Scanner Use the ScanDiagnostic application to troubleshoot problems such as the inability to read a bar code or a scanner that does not turn on. 1 From the Home menu, tap Start > ScanDiagnostic. 2 From the Scan Health screen, select the scanner you want to troubleshoot and then tap Diagnose. The application checks to make sure the scanner is enabled and checks settings to make sure they are optimized.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution The computer appears to be locked up and you cannot enter data. • Press the Power button and select Suspend from the Power Options menu. Press the Power button to turn the screen back on. • Press the Power button and select Reboot from the Power Options menu. • Remove the battery and press the Reset button to perform a cold boot. For help, see “Cold Boot the Computer” on page 115. • Try reloading the firmware.
Chapter 8 — Troubleshoot and Maintain the Computer Call Product Support If you cannot find the answer to your problem in the “Troubleshooting the Computer” section, you can visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support.
Chapter 8 — Troubleshoot and Maintain the Computer Find Your Operating System Version Use the following procedure to find the OS version of your mobile computer. 1 Press the Intermec Dashboard (m) button to launch the Dashboard. 2 Tap the Information bar. The Information Details page appears and displays information such as the firmware version and the OS version.
Chapter 8 — Troubleshoot and Maintain the Computer Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All other data, such as configuration and network settings, is preserved. 1 Press the Power button to suspend the computer. 2 Remove the handstrap and the battery pack. 3 Press the Reset button in the battery compartment on the back of the computer. 4 Replace the battery and the handstrap.
Chapter 8 — Troubleshoot and Maintain the Computer Clean Boot the Computer A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of those found in the Flash File Store, or any removable storage. If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and running for further troubleshooting. You can perform a clean boot using the mobile computer.
Chapter 8 — Troubleshoot and Maintain the Computer 1 Press the Power button and choose to suspend the computer. 2 Dip a clean cloth towel in the ammonia solution and wring out the excess. 3 Wipe off the imager window, camera lens, and flash area. Do not allow any abrasive material to touch these surfaces. 4 Wipe dry.
A Specifications and Default Settings 119
Appendix A — Specifications and Default Settings Physical and Environmental Specifications CN70 Physical Dimensions Dimensions 16.9 x 8.0 x 3.4 cm (6.66 x 3.14 x 1.35 in) Weight 450 g (15.2 oz) with battery CN70e Physical Dimensions Dimensions 19.5 x 8.0 x 3.4 cm (7.66 x 3.14 x 1.35 in) Weight 491 g (16.6 oz) with battery CK70 Physical Dimensions Dimensions 23.7 x 8.0 x 4.3 cm (9.33 x 3.16 x 1.69 in) Weight 562 g (19 oz) with battery CK71 Physical Dimensions Dimensions 23.7 x 8.0 x 5.0 cm (9.33 x 3.
Appendix A — Specifications and Default Settings Power and Electrical Specifications Battery type Rechargeable Lithium-ion (Li-ion) battery Battery capacity CN70/CN70e: 3.7 V, 4000 mAh (14.8 Wh) CK70/CK71: 3.7 V, 5200 mAh (19.2 Wh) Electrical rating x 4.37/4.8 V; 2/1,5 A 70 Series Non-Incendive Computer Specifications The 70 Series mobile computers with non-incendive (NI) certification comply with the following specifications for North America and Canada regions only.
Appendix A — Specifications and Default Settings Imaging options 5 megapixel color camera and EA30 area imager (all), EV12 (CK71 only), or EX25 (CK71 only) Back Accessory Interface Pin-outs The back accessory interface provides power for peripheral devices out the back of the CK70 and CK71 computers.
Appendix A — Specifications and Default Settings Wireless LAN Standards compliant IEEE 802.11a/b/g/n (2.4 GHz and 5 GHz), Single Stream Data rates up to 72Mbps Security 802.11i, WPA, WPA2, 802.1x (EAP-TLS, TTLS, , PEAP, EAP-FAST), WEP Certifications WPA2™ (Enterprise, Personal), WPA™ (Enterprise, Personal), Wi-Fi, WMM®, WMM Power Save, Cisco Compatible Extensions (CCX 4.
Appendix A — Specifications and Default Settings GS1 DataBar Limited TLC 39* * These symbologies are not supported with the EV12 imager in the CK71. Imager Reading Distances Typical reading distances are done in an office environment using office lights (4 lux). Minimum distances are measured in the dark (0 lux). Both reading distances are provided in respective scan engine integration guides. Contact your local Intermec representative for more information.
Appendix A — Specifications and Default Settings EA30 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" 20" 24" 28" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 EA30 Minimum Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.1 mm (4 mils) 0.1250 mm (5 mils) 0.
Appendix A — Specifications and Default Settings EA30 Area Imager Typical Reading Distances Typical distances are measured in an office environment (250 lux). 0" 4" 8" 12" 16" 20" 24" 28" 32" 36" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 80 90 EA30 Typical Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.
Appendix A — Specifications and Default Settings EV12 Linear Imager Minimum Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Minimum reading distances are measured in the dark (0 lux). 0" in 2" 4" 8" 6" 10" 12" 14" 16" 8" 20 7" 6" 15 EAN/UPC 100% 5" 4" 10 3" 5 2" 1" 0 0" 1" 5 2" 3" 0.125 mm / 5 mils 10 4" 0.25 mm / 10 mils 5" 6" 15 0.
Appendix A — Specifications and Default Settings EV12 LInear Imager Typical Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Typical reading distances are measured in an office environment (200 lux). 0" in 4" 8" 12" 16" 20" 24" 28" 32" 36" 16" 40 14" 12" 30 10" EAN/UPC 100% 8" 20 6" 10 4" 2" 0 0" 2" 10 4" 6" 0.125 mm / 5 mils 20 8" 0.25 mm / 10 mils 10" 12" 30 0.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Minimum Reading Distance Minimum reading distances are measured in the dark (0 lux). The following graphic does not include the 0.24 cm (0.09 in) setback for the CK71. 0” 16” 32” 48” 64” 80” 96” 128” 112” 144” 160” 176” in 80” 200 64” 160 100% EAN contrast UPC 48” 120 32” 80 16” 40 0” 0 16” 40 32” 80 0.25 mm/10 mils 48” 120 0.5 mm/20 mils 1 mm/40 mils 64” 160 1.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Typical Reading Distance Typical reading distances are measured in an office environment (200 lux). The following graphics do not include the 0.24 cm (0.09 in) setback for the CK71. EX25 Near-Far Range Imager 1D Typical Reading Distances 0” 40” 80” 120” 160” 200” 240” 280” 320” 360” 400” 440” 480” in 160” 400 128” 320 100% EAN contrast UPC 96” 240 64” 160 32” 80 0” 0 32” 80 0.25 mm 10 mils 160 64” 0.
Appendix A — Specifications and Default Settings EX25 1D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance Code 39 0.25 mm (10 mils) 0.5 mm (20 mils) 1 mm (40 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 15 cm (5.91 in) 16 cm (6.30 in) 25 cm (9.84 in) 40 cm (15.75 in) ** 135 cm (53.15 in) 280 cm (110.24 in) 550 cm (216.54 in) 720 cm (283.46 in) 1200 cm (472.44 in) Code 128 retro-reflective 2.5 mm (100 mils) ** 1300 cm (511.
Appendix A — Specifications and Default Settings EX25 2D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance DataMatrix 0.25 mm (10 mils) 0.76 mm (30 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 7.5 mm (300 mils) 15 cm (5.91 in) 25 cm (9.84 in) ** ** 20 cm (7.87 in) 90 cm (35.43 in) 310 cm (122.05 in) 450 cm (177.17 in) 1100 cm (433.07 in) 1524 cm (600 in) ** Minimum distance depends on bar code width and scan angle.
Appendix A — Specifications and Default Settings Symbology Default Value Aztec Disable BPO Disable CanadaPost Disable Codabar Disable Codablock A Disable Codablock F Disable Code 11 Disable Code 39 Enable Code 93 Disable Code 128/GS1-128 Enable DataMatrix Enable DutchPost Disable EAN/UPC Enable UPC A, UPC E, EAN 8, EAN 13 GS1 Composite Disable GS1 DataBar Expanded Disable GS1 DataBar Limited Disable GS1 DataBar Omni-Directional Disable Infomail Disable Intelligent Mail
Appendix A — Specifications and Default Settings Symbology Default Value Telepen Disable TLC 39 Disable Symbology Option Settings Symbology Option Settings Default Value Preamble None (Disabled) Postamble None (Disabled) Symbology Identifier Disable Multicode Disable Scanner Settings Scanner Settings Default Value Trigger Predefined Modes Level Trigger Mode Level Aimer Mode Typical aimer Hardware Trigger Enable Trigger Timeout (sec) 2 Aiming Duration (msec) 500 Turn Off After G
Appendix A — Specifications and Default Settings Imager Settings Default Value Image Capture Output Compression Output Compression Quality Edge Enhancement Noise Reduction Subsampling Image Rotation Image Lighting Correction Bitmap 0 None 0 None None Disable Decode Security Settings Decode Security Settings Default Value Consecutive Data Validation 0 Identical Consecutive Timeout 300 ms Different Consecutive Timeout 0 Center Decoding Disable Center Decoding Tolerance 0 Communications Use com
Appendix A — Specifications and Default Settings 802.11 Radio Setting Default Value Import Pac Files False Radio Bands b/g (2.
Appendix A — Specifications and Default Settings Good Read Setting Default Value Tethered Scanner One Beep Bluetooth Scanner Good Read Beep One Beep Backlight Settings Backlight Setting Default Value Display Backlight Adjustment Normal Keypad Backlight On Based on Light Level Light Level Low Screen Settings Screen Setting Default Value Screen Rotations Portrait 0 Degrees Screen Rotation Sensor Disabled Sound Settings Sound Setting Default Value Beeper and Voice Medium Headset Beeper
Appendix A — Specifications and Default Settings Power Management Setting Default Value Power Button Behavior Suspend Device Turns Off After (Battery Power) 5 minutes Screen Turns Off After (Battery Power) Disabled Device Turns Off After (External Power) Disabled Screen Turns Off After (External Power) Disabled Device Off Sensor Disabled Profiles Settings Application Profiles Settings Default Value Camera Disable Camera Scan Enable Camera Scan Show Option in Profile Settings Show Option in
Appendix A — Specifications and Default Settings Core Messaging Service Settings Use core messaging service settings to configure the message routers between client and server software applications. Core Messaging Service Core Messaging Service Setting Default Value Associated Server IP Null Broadcast Name INTERMEC Port 62241 Keep Alive Ping Interval 30 Seconds Device Monitor Settings Use device monitor settings to configure how the mobile computer monitors the network.
Appendix A — Specifications and Default Settings Virtual Wedge Settings Use virtual wedge settings to configure the virtual wedge.
B Keypads and Keystrokes 141
Appendix B — Keypads and Keystrokes Standard Characters Use the following tables to learn how to enter standard and other available characters and functions with the keypad. If there is no sequence of keystrokes for a particular character or function, it is only available through the soft input panel (SIP), which you can access by tapping the keyboard icon on the touch screen. Note: You can only enter “8” and “#” characters in the phone or contacts applications.
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad n c66 c666 c7 c77 c777 c7777 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 N O P Q R S T U V W X Y Z yA yB yC yD yE yF yG yH o p q r s t u v w x y z A B C D E F G H 70 Series Mobile Computer User Manual 143
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad I c1444 c15 c155 c1555 c16 c166 c1666 c17 c177 c1777 c17777 c18 c188 c1888 c19 c199 c1999 c19999 0 1 2 yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV yW yX yY yZ b, bY bU J K L M N O P Q R S T U V W X Y Z 0 1 2 144 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad 3 3 4 5 6 7 8 9 bI bH bJ bK bB bN bM 4 5 6 7 8 9 CN70 Characters and Functions To Enter Numeric Keypad QWERTY Keypad @ (at symbol) N/A & (ampersand) N/A * (asterisk) * : (colon) N/A , (comma) N/A $ (dollar) N/A ! (exclamation) N/A - (hyphen) - % (percent) N/A . (period) . b# bQ bS bC bD bX bE bO bG bR .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad QWERTY Keypad ? (question mark) N/A ‘ (apostrophe) N/A Forward Tab j { u d l r c1 e b| b or c c0 b m or c m | p w m bA bZ j { u d l r yy e bP b or y s bm | p w m Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard 146 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CN70e Keypads and Keystrokes CN70e Alphanumeric Characters Character Numeric Keypad a b c d e f g h i j k l m n o p q r s c2 c22 c222 c3 c33 c333 c4 c44 c444 c5 c55 c555 c6 c66 c666 c7 c77 c777 c7777 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c8 c88 c888 c9 c99 c999 c4 c44 c444 c5 c55 c555 c6 c66 c666 c1 c11 c111 c1111 A B C D E F G H I J K L M N O P Q R S 147
Appendix B — Keypads and Keystrokes Character Numeric Keypad t u v w x y z A B C D E F G H I J K L M N 148 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 c1444 c15 c155 c1555 c16 c166 Calculator-Style Keypad QWERTY Numeric Keypad c2 c22 c222 c3 c33 c333 c3333 c78 c788 c7888 c79 c799 c7999 c74 c744 c7444 c75 c755 c7555 c76 c766 T U V W X Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 c1666 c17 c177 c1777 c1777 7 c18 c188 c1888 c19 c199 c1999 c1999 9 0 1 2 3 4 5 6 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c7666 c71 c711 c7111 c7111 1 c72 c722 c7222 c73 c733 c7333 c7333 3 0 1 2 3 4 5 6 yO yP yQ yR yS yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 149
Appendix B — Keypads and Keystrokes Character Numeric Keypad 7 8 9 7 8 9 Calculator-Style Keypad QWERTY Numeric Keypad 7 8 9 7 8 9 CN70e Characters and Functions To Enter Numeric Keypad Calculator-Style Keypad @ (at symbol) N/A N/A & (ampersand) N/A N/A * (asterisk) * * : (colon) N/A N/A , (comma) N/A N/A $ (dollar) N/A N/A ! (exclamation) N/A N/A - (hyphen) - - % (percent) N/A N/A . (period) . b# .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad Calculator-Style Keypad QWERTY Numeric Keypad Up Arrow u d l r c1 e b| b or c c0 b m or c m | p w m u d l r c7 e b| b or c c0 b m or c m | p w m u d l r yy e b| b or y s bm | p w m Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard CK70 Keypads and Keystrokes CK70 Alphanumeric Characters Character Large Alpha Keypad Alphanumeric Keypad a A B C A B C b c 70 Series Mob
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad d D E F G H I J K L M N O P Q R S T U V W X D E F G H I J K L M N O P Q R S T U V W X e f g h i j k l m n o p q r s t u v w x 152 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad y Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS z A B C D E F G H I J K L M N O P Q R S 70 Series Mobile Computer User Manual 153
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad T yT yU yV yW yX yY yZ bP bD bE bF bG bH bI bK bL bM yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 U V W X Y Z 0 1 2 3 4 5 6 7 8 9 CK70 Characters and Functions To Enter Large Alpha Keypad Alphanumeric Keypad @ (at symbol) bS bW N/A & (ampersand) 154 bU 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad * (asterisk) bO bJ cJ bT cS cW cX cO . bX bQ cQ cT bY cY cN bN bV cV b0 b2 b5 cX : (colon) ; (semicolon) , (comma) $ (dollar) ! (exclamation) - (hyphen or minus) % (percent) .
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad ~ (tilde) N/A \ (backslash) cU bU bW c8 b8 bZ / (forward slash) “ (quotes) N/A ( (left parenthesis) bR cR bZ cZ bs ) (right parenthesis) Insert Delete Sym ¦ (broken vertical bar) ̀ (grave) Forward Tab Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift 156 N/A N/A j { u d l r yy e cm y N/A N/A b4 b6 N/A cS cW j { u d l r yy e cm y 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad Space s b m or c m | s b m or c m | Alt N/A Alt Ctrl Ctrl Ctrl Send Call bA bC m c1 c3 m To Enter Large Alpha Keypad Alphanumeric Keypad F1 cD cE cF cG cH cI cK cL cM cP ¡ ¢ £ ¤ ¥ b¡ b¢ b£ b¤ b¥ bA bB Start (Windows) Esc End Call Intermec Dashboard CK70 Function Keys F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 N/A N/A 70 Series Mobile Computer User Manual 157
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad F13 Alphanumeric Keypad bC bD bE bF bG bH bI bJ bK bL bM bN N/A F14 N/A F15 N/A F16 N/A F17 N/A F18 N/A F19 N/A F20 N/A F21 N/A F22 N/A F23 N/A F24 N/A CK71 Keypads and Keystrokes CK71 Alphanumeric Characters Character Numeric With Function Keys Keypad Alphanumeric Keypad a b7 b8 b9 b4 b5 b6 A B C D E F b c d e f 158 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad g b1 b2 b3 b0 bb¡ b¢ b£ b¤ b¥ b¦ b§ b¨ b© bª b« b¬ bm b Ctrl b Alt by7 G H I J K L M N O P Q R S T U V W X Y Z yA h i j k l m n o p q r s t u v w x y z A 70 Series Mobile Computer User Manual 159
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad B by8 by9 by4 by5 by6 by1 by2 by3 by0 byby¡ by¢ by£ by¤ by¥ by¦ by§ by¨ by© byª by« yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV C D E F G H I J K L M N O P Q R S T U V 160 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad W by¬ bym b y Ctrl b y Alt 0 1 2 3 4 5 6 7 8 9 yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 X Y Z 0 1 2 3 4 5 6 7 8 9 CK71 Characters and Functions To Enter Numeric With Function Keys Keypad Alphanumeric Keypad : (colon) cs ; (semicolon) N/A b8 b5 cX , (comma) $ (dollar) ! (exclamation) N/A cS cW 70 Series Mobile Computer User Manual N/A N/A 161
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad - (hyphen or minus) . cs . bs bY bS cX cV bV bT cT bU cU bW c2 b2 bZ b4 b6 cS cW j .
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Backspace { u d l r yy e cm y s b m or c m | { u d l r yy e cm y s b m or c m | b| Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Alt Alt Ctrl Ctrl Ctrl Intermec Dashboard m m To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F1 ¡ ¢ £ ¤ ¡ ¢ £ ¤ CK71 Function Keys F2 F3 F4 70 Series Mobile Computer User Manual 163
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F5 ¥ ¦ § ¨ © ª « ¬ c¡ c¢ c£ c¤ c¥ c¦ c§ c¨ c© cª c« c¬ ¥ b¡ b¢ b£ b¤ b¥ bA bB bC bD bE bF bG bH bI bJ bK bL bM bN F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 164 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CK71 Intermec Terminal Emulation (ITE) Keys To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Attention c0 Autolog N/A Clear b6 Duplicate N/A EEOF N/A Erase N/A cA c¤ c6 cD c¥ cE cF c1 c1 cG b3 cI cH cK cM cO cN b9 c¡ c¢ Find Field + Field Fieldmark Help Hex Home Keypad Menu Mode New Line Next Screen PA1 PA2 N/A cx bx N/A N/A N/A c.
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad PA3 c3 cd c£ cd cP c7 cR c| ce c5 c8 cQ bd Page Print N/A Previous Screen c7 Remove N/A Reset c| ce c5 c8 br Return Roll Down Roll Up System Request View View Down View Up 166 N/A bd bu N/A N/A 70 Series Mobile Computer User Manual
C ScanNGo Wi-Fi Configuration Bar Codes You can use the ScanNGo Wi-Fi configuration bar codes to quickly configure the 802.11 radio in your computer.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes Radio Configuration Bar Codes Use the following ScanNGo bar codes to enable the 802.11 radio and set the defaults for either Funk or Microsoft Wireless Zero Configuration security. After you scan the bar codes, you will still need to use Intermec Settings or another configuration program to set network-specific settings on your computer and to configure the wireless security. The CN70, CN70e, and CK70 are available with the EA30 imager only.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 2D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 1D Configuration Bar Codes You can configure the computer with a 1D imager (EV12). 1 Scan the START HERE bar code from the table and wait for the program to start. 2 Scan the 1/9 bar code. 3 Scan the rest of the bar codes in any order.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 1D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 170 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 70 Series Mobile Computer User Manual 171
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 172 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 70 Series Mobile Computer User Manual 173
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 174 70 Series Mobile Computer User Manual
I Index 175
Index Symbols .cab files, using to install applications 100 Numerics 70 Series computer models 2 features 5 802.11 communications, configuring 77 802.11 network status, troubleshooting 109 802.11 radio, default settings 135 802.
Index characters entering on CK70/CK71 keypad 23 entering on numeric keypad 22 entering on QWERTY keypad 22 entering with keystrokes 142–166 charging accessories 10 charging the battery 10 CK70 keypads, illustrated 18, 19 keystrokes, listed 151–158 status LEDs 6, 7 CK70/CK71 battery, described 8 entering characters on keypad 23 magstripe reader adapter, described 8 CK71 keypads, illustrated 20, 21 keystrokes, listed 158–166 status LEDs 7 clean boot, performing 117 cleaning computer 117 CN70 keypads, illustr
Index Funk security (continued) configuring static WEP 89 configuring WPA Enterprise (802.1x) 86 configuring WPA Personal (PSK) 87 configuring WPA2 Enterprise (802.
Index LEDs battery status, described 13 status descriptions 7 Location of the CK70 Status LEDs 7 Location, status LEDs 7 locked computer, troubleshooting 113 M magstripe reader adapter, described 8 magstripe reader snap-on adapter, described 8 mass storage device, using computer as 36 memory, computer 121 microSD card about 29 installing in a CK70/CK71 32 installing in a CN70/CN70e 29 updating system software 103 using to save pictures and videos 61 Microsoft security choosing 90 configuring 802.
Index Q QWERTY keypad CN70, illustrated 15 entering characters on 22 illustrated 15 QWERTY numeric keypad CN70e, illustrated 16 R reading distances EA30 area imager 125 EV12 linear imager 127 EX25 imager 129 Ready-to-Work LED description 7 reboot performing 115 power option description 25 recording a video 61 regulatory approvals 123 reset button, location 116 performing 115 RS-232 snap-on adapter, described 9 S scan handle, described 9 ScanDiagnostic Intermec application description 44 using to troubleshoo
Index tethered stylus replacement kit, described 9 Tile bar description 38 illustration 38 Title bar description 38 illustration 38 status icon descriptions 40 transferring files, to and from PC 35 troubleshooting 107–111 802.11 network status 109 802.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2012 Intermec Technologies Corporation. All rights reserved.
