CN3 Mobile Computer for Windows Mobile 6.
Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation.
Document Change Record This page records changes to this document. The document was originally released as Revision 001. Version Number Date Description of Change 004 2/2010 Added operating temperature for CN3e and made a few minor corrections to Appendix A. 003 11/2009 Revised to include updated information for CN3 firmware release 4.30. 002 4/2009 Added default configuration, keypad and keystroke information, and descriptions of how to use the CN3 phone.
iv CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Contents Contents Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Global Services and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Calibrating the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Configuring the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Understanding the Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Using the Imager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Connecting to a Bluetooth Audio Device. . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Using Serial and USB Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Managing Network Connections With iConnect. . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Connecting to a Network With a RAS Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Connecting to a Network with a VPN Server. . . . . . . . . . . . . . . . . .
Contents Troubleshooting the CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Checking 802.11 Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Resetting the CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Warm Booting the CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions.
Before You Begin Web Support Visit the Intermec web site at www.intermec.com to download our current manuals (in PDF). Visit the Intermec technical knowledge base (Knowledge Central) at www.intermec.com and click Support > Knowledge Central to review technical information or to request technical support for your Intermec product. Telephone Support In the U.S.A. and Canada, call 1-800-755-5505. Outside the U.S.A. and Canada, contact your local Intermec representative.
Before You Begin Who Should Read This Manual This manual is written for the person who is responsible for installing, configuring, and maintaining the CN3 and CN3e Mobile Computer. This manual provides you with information about the features of the CN3 and CN3e, and how to install, configure, operate, maintain, and troubleshoot it. Before you work with the CN3 or CN3e, you should be familiar with your network and general networking terms, such as IP address. Related Documents The Intermec web site at www.
Before You Begin 5798509; 5798513; 5804805; 5805807; 5811776; 5811777; 5818027; 5821523; 5828052; 5831819; 5834753; 5834749; 5837987; 5841121; 5842070; 5844222; 5854478; 5862267; 5869840; 5873070; 5877486; 5878395; 5883492; 5883493; 5886338; 5889386; 5892971; 5895906; 5898162; 5902987; 5902988; 5912452; 5923022; 5936224; 5949056; 5969321; 5969326; 5969328; 5979768; 5986435; 5987192; 5987499; 5992750; 6003775; 6012640; 6016960; 6018597; 6024289; 6034379; 6036093; 6039252; 6064763; 6075340; 6095422; 6097839;
1 Using the CN3 This chapter introduces the CN3 and CN3e Mobile Computers with Windows® Mobile® 6.1. It also contains hardware and software configuration information to assist you in getting the most out of your computer.
Chapter 1 — Using the CN3 Introducing the CN3 Mobile Computer The Intermec CN3, CN3e, and CN3NI Mobile Computers are ergonomically designed mobile computers built on the Microsoft Windows Mobile® 6.1 operating system. They are lightweight, easyto-use, and run most software developed for the Windows Mobile platform, including standalone, client-server, and browser-based applications. The CN3, CN3e, and CN3NI support similar feature sets.
Chapter 1 — Using the CN3 Standard CN3 and CN3e features include: • GPS, 802.11b/g, and Bluetooth® radios. • A 2-megapixel color camera or an EA11 Area Imager • 128 MB RAM • A numeric, QWERTY (CN3), or alphabetic (CN3e) keypad. You can also order an optional GSM/GPRS/EDGE WWAN radio for the CN3. Note: The 802.11 radio also supports the 802.11d standard, which adds the requirements and definitions for 802.11 WLAN equipment for operation in markets not served by the current standard. For 802.
Chapter 1 — Using the CN3 Using the Battery The CN3 Series computers use the following Intermec batteries as a main power source. All have been certified to meet the IEEE 1725 standard for rechargeable batteries. Standard and Extended Batteries for CN3 Series Computers Computer Uses This Standard Battery Uses This Extended Battery CN3 AB8 or AB15 AB9 or AB16 CN3e N/A AB9 or AB16 CN3NI N/A AB28 Standard batteries have 8.1 Watt hours capacity and extended batteries have 14.8 Watt hours capacity.
Chapter 1 — Using the CN3 The battery is fully charged when the battery status LED shows a steady green. To charge the battery • Insert the battery into a quad battery charger, a single dock, or a multidock, or attach external power to the CN3 with the battery installed. For information on these accessories, see “Accessories” on page 107. For all charging methods, it takes 5 hours or less to fully charge the CN3 batteries.
Chapter 1 — Using the CN3 Battery release tab Removing the Battery in a CN3e 4 Place the end of the battery into the battery compartment as shown in the next illustration, and press down on the other end of the battery until it clicks into place. 5 Snap the top of the handstrap into place. 6 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 Checking the Battery Status A quick way to check the status of your battery is to look at the battery icon on the CN3 Status bar. Battery Icon Status Icon Status Battery is fully charged. Battery has a medium charge. You should be able to work for several more hours before changing batteries. Battery is low. You need to replace or charge the battery soon. Battery is critically low. You need to replace or charge the battery now. Battery is charging.
Chapter 1 — Using the CN3 Understanding the Battery Status LED (continued) Battery Status Description Steady amber The battery is missing or unable to charge. If the battery will not charge, it may be because the temperature is outside of the charging range, or you may be using a battery not approved by Intermec. You need to use one of the battery models specified in “Standard and Extended Batteries for CN3 Series Computers” on page 4.
Chapter 1 — Using the CN3 Maximizing Battery Life Batteries are chemical devices. If the batteries are left sitting on a shelf for long periods of time outside the CN3, the batteries slowly discharge, eventually to zero if left uncharged. The battery chemistry resists normal degradation if you store the battery in a charger as opposed to leaving the battery in a discharged state. See the following table for tips you can do to maximize the life of your battery.
Chapter 1 — Using the CN3 There are several ways you can manage power: • You can set the amount of time that the screen stays on, or the amount of time the CN3 stays on after the screen turns off. For help, see “Customizing Power Timeouts” on page 11. • You can change the amount of time the screen backlight stays on. For help, see “Configuring the Backlight” on page 23. • You can choose a Power Management Profile to manage power based on the way you use your CN3.
Chapter 1 — Using the CN3 Power Profiler also provides advanced settings that allow you to finetune the power usage. You can choose to have the Power button turn off the screen or turn off the device. Note: You can also configure all of the settings in Power Profiler using Intermec Settings. For help with Intermec Settings, see “Configuring the CN3 Parameters” on page 45.
Chapter 1 — Using the CN3 To customize power timeout values 1 Tap Start > Settings > System tab > Power Profiler. 2 In the Power Profile tab, tap Enable Advanced Settings. 3 Tap the Screen Settings tab to change screen timeout values: • Check the Enable Screen Off check box to be able to turn off the screen independently of the CN3. • To change the amount of inactivity time before the screen turns off, move the Battery Power or External Power sliders. For battery power, choose from 1 to 6 minutes.
Chapter 1 — Using the CN3 Using the Keypad The CN3 comes with either a QWERTY keypad or a numeric keypad. The CN3e comes with either an alphabetic keypad, a phone-style numeric keypad (1-2-3 digits across the top), or a 10-key numeric keypad (7-8-9 digits across the top). The QWERTY and alphabetic keypads are for applications that require mainly alphabetic data. .The numeric keypads are for applications requiring mainly numeric data.
Chapter 1 — Using the CN3 CN3e Alphabetic Keypad Note: Some available characters are not printed on the keypad overlays. For a complete list of available characters, see Appendix C, “Keypads and Keystrokes.” Using the Color-Coded Keys All keypads include color-coded modifier keys for characters, symbols, and functions printed on the keypad overlay. The numeric keypads include an orange b modifier key and a green c modifier key. The alphanumeric keypads include an orange b modifier key.
Chapter 1 — Using the CN3 Using the Color-Coded Keys (continued) To Do This Press Example Unlock a green or orange key. b or c once. Press the b or c once to unlock the key and turn off the LED. Entering Characters on the Alphabetic and QWERTY Keypads Press the key for the character to type that character. To type a character or access a function printed on the keypad overlay, press b and then press the key for the character or function you want.
Chapter 1 — Using the CN3 Using the Green Key Lock Feature Press c c to enable the Green Key Lock feature. When the green c key is locked, you can type letters without pressing c before each number key. • While the green key is locked, press 1 to toggle between only uppercase and lowercase letters. • To turn off the Green Key Lock, press c. Note: If you turn off the Green Key Lock, you may need to press c 1 to return to lowercase letters if uppercase letters were previously enabled.
Chapter 1 — Using the CN3 Using the Power Button Press the Power ^ button to put the CN3 into Suspend mode. Power button Power button In this lower power mode, the CN3 continues to supply power to all memory, but turns off power to most hardware such as the display. This feature is designed to prolong battery life. Note: If you do not have a SIM card installed, it may take up to 30 seconds for the CN3 to suspend. Understanding the Audio Features There are several audio features available on the CN3.
Chapter 1 — Using the CN3 When you use the CN3 as a cell phone, use the microphone and front speaker for talking on the phone. Front speaker (located on end) Microphone Microphone and Front Speaker Locations To adjust the volume of the front speaker 1 Tap the Volume ( ) icon at the top of the screen. 2 In the Volume adjust box, tap On. 3 Move the volume slider for the phone. Phone volume slider 18 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 Adjusting the Volume of the Rear Speaker The rear speaker is used for all other computer audio. You can set the volume to off, very low, medium (default), high, and very high. Use the following table to understand the different ways to adjust the volume. Rear speaker Volume down Volume up Location of the Rear Speaker and Volume Control Choose one of these methods to change the rear speaker volume.
Chapter 1 — Using the CN3 • Use Intermec Settings to set the default volume. For help, see “Configuring the CN3 Parameters” on page 45. Enabling the Vibrate Mode You can enable the vibrate mode when audio is difficult to hear, such as in a high noise environment. When enabled, the CN3 vibrates when the scanner performs a good read or when the phone receives a call. To enable the vibrate feature 1 Tap the Volume icon ( ) at the top of the screen. 2 Tap Vibrate.
Chapter 1 — Using the CN3 Status bar Today screen Command bar The Windows Mobile Today Screen Using the Stylus Your computer has a stylus for selecting items and entering information on the touch screen. Functions You Can Perform With the Stylus Action Description Tap Touch the screen once with the stylus to select options, open or close applications, or launch menus from the Command bar. Drag Hold the stylus on the screen and drag across the screen to select text and images.
Chapter 1 — Using the CN3 Understanding the Screen Icons Use the screen icons on the Navigation bar and the Command bar to see the battery status, network connections, and so on. Some standard Microsoft icons are included in this table. Computer Screen Icons Icon Description The battery is full. The battery is low. You need to replace or charge the battery very soon. The battery is charging. The volume is turned off. To turn the volume back on, tap this icon and choose your setting.
Chapter 1 — Using the CN3 To align the touch screen using the keypad 1 Press the Windows button on the upper left of the keypad. 2 Press the Down button to select Settings. 3 Press Enter. 4 Press the Tab button until the Settings tabs are highlighted. 5 Press the Right Arrow button to select the System tab (on some keypads this will be the orange button and down button). 6 Press tab until the Screen icon is highlighted. 7 Tab to Align Screen and press Enter follow the instructions to align the screen.
Chapter 1 — Using the CN3 You can also use Intermec Settings to configure the backlight settings. For help, see “Configuring the CN3 Parameters” on page 45. Understanding the Status LEDs The status LEDs above the display show the following information: Good Read LED and Intermec Ready-to-Work indicator Notification LED Battery status LED . Understanding the LEDs 24 LED Color Description Notification Orange The CN3 is notifying you of a pending alarm or message.
Chapter 1 — Using the CN3 Understanding the LEDs (continued) LED Color Ready-to-Work Blue indicator™ Description The CN3 is suspending or resuming with the display turned off. TE 2000 or Intermec Terminal Emulator (ITE) is running and connected to the host. Blinking blue TE 2000 or ITE is running but not connected to the host. Off TE 2000 or ITE is not installed or not running.
Chapter 1 — Using the CN3 Reading Bar Codes The CN3 imager can scan 1D and 2D bar code symbologies, composite symbologies, and postal codes. You can position the CN3 in almost any orientation to scan a bar code label. Imager Scan button Locating the Imager and the Side Scan Button Note: There is also one scan button on the front of the CN3 and two scan buttons on the front of the CN3e.
Chapter 1 — Using the CN3 Laser pointer 4 When a bar code label is successfully read, the CN3 makes a high beep and the Good Read LED lights briefly. 5 Release the Scan button. By default, these bar code symbologies are enabled on the CN3: • Code 39 • Code 128/GS1-128 • UPC-A • UPC-E • EAN-8 • EAN-13 • PDF417 • DataMatrix CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 If you are using bar code labels that are encoded in a different symbology, you need to enable the symbology on the computer. Use Intermec Settings to enable and disable symbologies. For help, see “Configuring the CN3 Parameters” on page 45. Improving Imager Performance If you experience problems reading bar codes, try some of these tips to improve imager performance. • Keep your hand as steady as possible while scanning a label.
Chapter 1 — Using the CN3 Capturing Images The Data Collection Resource Kit includes .NET classes you use in your image capture applications. For more information, see “Developing Applications for the CN3” on page 72. The CN3 includes Image Capture, a utility application that demonstrates this feature. Using the Image Capture Application 1 Tap Start > Programs > Image Capture. The Image Capture main screen shows streaming video from the imager.
Chapter 1 — Using the CN3 4 Tap-and-drag to scroll the image. Tap to zoom in, or tap To save the image, tap to zoom out. . To discard the image, tap . By default, images are saved to the My Documents\ImageCapture directory on the CN3, with the filename Image_$. After you save or discard an image, the main screen appears and the CN3 is ready to capture another image. 5 To view saved images, tap Options and choose Gallery. Tap and to view the images one at a time.
Chapter 1 — Using the CN3 To configure Image Capture settings 1 Tap Options and choose Settings. 2 Change settings as needed. For help, see the next table. Image Capture Settings Descriptions Setting Description Edge Enhancement Adjusts contrast to enhance the edges of objects. Default is Medium. Too high a setting for the environment adds noise to the image.
Chapter 1 — Using the CN3 Integrating Image Capture Into Your Application You can integrate Image Capture into your own application by calling it from your application. You can also customize Image Capture settings by creating and editing the Image Capture configuration .xml file. For help, see “Integrating Image Capture” on page 76. Capturing Signatures A signature capture is a grayscale image of a signature on paper or other business form.
Chapter 1 — Using the CN3 You can take photos in either high-resolution or compressed format, with resolutions up to 1600 x 1200 pixels. When you take a picture, the images are saved as .jpg files and stored in the /My Documents/ My Pictures folder. You can use the Pictures & Videos application on the CN3 to take, view, and edit pictures or record and launch video clips stored on the CN3 or a storage card.
Chapter 1 — Using the CN3 2 Select a file save location, type a filename prefix, and select a compression level. 3 Tap ok. Installing a miniSD or SIM Card You can corrupt your miniSD™ card if you do not follow these installation and removal procedures exactly. Before installing a miniSD card, inspect the gasket in the compartment for any damage or wear, and contact your Intermec representative if you find any damage or wear.
Chapter 1 — Using the CN3 SIM card SIM card slot miniSD card 5 Close the miniSD/SIM card slot door and insert the two screws. To prevent damage to the door, do not overtighten the screws that secure the door. Torque the screws to 0.11 Nm (1.0 in-lbs). 6 Replace the battery pack and then press the Power button. The CN3 cold boots. CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 Setting Up GPS on the CN3 If your CN3 comes equipped with an integrated Global Positioning System (GPS) receiver, it can deliver standards-based National Marine Electronics Association (NMEA) data strings to GPS applications. Intermec recommends that you use the GPS Intermediate Driver (GPSID) instead of directly accessing the GPS hardware. The GPSID is a Microsoft software component that interacts between applications and the GPS hardware.
Chapter 1 — Using the CN3 3 On the Programs tab, select the COM port that you want your programs to use to get GPS data from your CN3. Note: COM1 and COM3 are reserved. 4 Tap the Hardware tab, and select these settings. GPS hardware port: COM3 Baud rate: 57600 5 Tap the Access tab and select the Manage GPS automatically check box. CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 6 Tap ok. To enable extended ephemeris 1 Tap Start > Settings > the System tab. 2 Tap iGPS settings. The iGPS Settings screen appears. 3 Tap the Advanced tab. 4 Select the Enable extended ephemeris check box. 5 Tap ok. 38 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 Learning About Additional GPS Options for the CN3 Intermec provides enhanced feature support for the Extended Ephemeris data capability. For the latest Extended Ephemeris data files and other CN3 downloads, visit the CN3 downloads page on the Intermec web site at www.intermec.com. For more information about programming for Extended Ephemeris GPS, visit the Intermec Developer Library at www.intermec.com/idl. CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 1 — Using the CN3 40 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
2 Connecting and Configuring the CN3 Use this chapter to understand how to configure the CN3 to communicate in your network.
Chapter 2 — Connecting and Configuring the CN3 Managing the CN3 With SmartSystems Foundation Intermec's SmartSystems™ Foundation is a software platform that lets you manage all of your SmartSystems-enabled devices, including the CN3, simultaneously from a central server. The SmartSystems console displays all SmartSystems-enabled computers and peripherals in your network.
Chapter 2 — Connecting and Configuring the CN3 With an AutoDeploy license, SmartSystems can automatically push software, configuration settings, and other files to connected CN3s. The license also enables Scan-to-Connect, which makes connecting additional CN3s to your wireless network as easy as reading bar codes. SmartSystems Foundation can be downloaded at no charge from the Intermec web site. For more information, visit www.intermec.com\SmartSystems.
Chapter 2 — Connecting and Configuring the CN3 Configuring the Phone The CN3 with Windows Mobile 6.1 supports GSM/EDGE cellular phone technology. With a WWAN radio module installed in the CN3, you can send and receive telephone calls as well as transmit data through wide-area (WAN) cellular networks. The CN3 provides a phone speaker, microphone, and speakerphone. It also supports the use of a Bluetooth headset or hands-free kit. The factory default setting for the phone is disabled.
Chapter 2 — Connecting and Configuring the CN3 To activate the GSM/EDGE phone • Install the SIM card in the CN3. For help, see “Installing a miniSD or SIM Card” on page 34. You may need to configure network settings for your provider. For information, tap Start > Help and see the procedures in the Windows Mobile online Help. Or, contact your network provider. Making a Phone Call After you activate your phone, you are ready to start making phone calls. To make a phone call 1 Tap Start > Phone.
Chapter 2 — Connecting and Configuring the CN3 Using Intermec Settings Remotely With SmartSystems Foundation Your CN3 is SmartSystems-enabled, which lets you open Intermec Settings from the SmartSystems Foundation console to remotely configure all of your CN3 computers. For more information on SmartSystems Foundation, see “Managing the CN3 With SmartSystems Foundation” on page 42. To open Intermec Settings from the SmartSystems console 1 In the SmartSystems console, right-click a CN3.
Chapter 2 — Connecting and Configuring the CN3 For help with using Intermec Settings, in the browser click Help > Contents. For information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual. Using Intermec Settings Directly On the CN3 You can use Intermec Settings on the CN3 to configure the computer and view system information. To use Intermec Settings 1 On the CN3, tap Start > Settings > the System tab > Intermec Settings. 2 Tap a menu bar.
Chapter 2 — Connecting and Configuring the CN3 In a list of configurable items, choose or change options by entering data in the entry fields or checking the appropriate check box. • Tap OK to save your changes. • Tap Cancel to discard your changes and return to the previous menu. 4 To close Intermec Settings, in the main menu tap ok or choose Menu > Exit. For more information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual.
Chapter 2 — Connecting and Configuring the CN3 Configuring the CN3 For Your Network You can easily add the CN3 to your wireless or wired data collection network. You can connect your CN3 using: • 802.11b/g radio communications. • Ethernet communications • Bluetooth communications. • USB and serial communications. Configuring 802.11b/g Radio Communications Make sure all components with antennas are at least 30 cm (1 ft) apart when power is applied. Failure to comply could result in equipment damage.
Chapter 2 — Connecting and Configuring the CN3 • AD10 single dock with an Ethernet/modem (AA12/AA13) adapter • AD11 Ethernet multidock • AA16 Ethernet snap-on adapter To use your CN3 in an Ethernet network 1 Connect the CN3 to an Ethernet network with an AD10, AD11, or AA16. Ethernet communication is enabled by default on the CN3. 2 Configure these network parameters: • If you have a DHCP server, enable DHCP.
Chapter 2 — Connecting and Configuring the CN3 4 Choose Yes. Intermec Settings refreshes the settings and returns you to the main menu. 5 (Optional) To make the CN3 visible to other Bluetooth devices, choose Communications > Bluetooth and choose Enable from the Discoverable menu. To make the CN3 connectable to other Bluetooth devices that discover it, choose Communications > Bluetooth and choose Enable from the Connectable menu. 6 Click OK.
Chapter 2 — Connecting and Configuring the CN3 Or, to search for scanners: a Tap Search and then tap Next. The CN3 looks for scanners, and the Bluetooth device names of found scanners appears in the list. b Tap the scanner device name in the list and then tap Next. The scanner is paired with the CN3. Or, to manually add a scanner: a Tap Manual and then tap Next. b Enter the Bluetooth address of the scanner in the entry field. c Tap Next. The scanner is paired with the CN3.
Chapter 2 — Connecting and Configuring the CN3 3 (Optional) Tap Print Test Page. The printer prints out a test page. After you configure Bluetooth wireless printing, you can use an application that opens the wireless printing COM port on your CN3. For help with developing applications, see the Bluetooth Resource Kit, part of the Intermec Developer Library (IDL), available from the Intermec web site at www.intermec.com/idl.
Chapter 2 — Connecting and Configuring the CN3 Using Serial and USB Communications You can use these CN3 accessories to transmit data to and receive data from another device through serial or USB communications: • AD10 single dock • AV6 vehicle dock (AV9 for CN3e) • AD11 multidock • AA18 USB adapter • AA17 RS-232 adapter For more information about these accessories and how to order them, see “Accessories” on page 107. Managing Network Connections With iConnect After you configure 802.
Chapter 2 — Connecting and Configuring the CN3 To configure or change wireless or Ethernet network settings 1 Tap the iConnect icon ( screen. ) in the lower right corner of the Today 2 Choose Tools > Wireless IP Settings or Ethernet IP Settings. A dialog box appears that shows the current settings for the wireless or Ethernet network adapter. 3 Change settings as needed and click ok. To check the connection status with a ping test 1 Tap the iConnect icon ( screen.
Chapter 2 — Connecting and Configuring the CN3 If you are having trouble with your wireless connection, you can use iConnect to verify available access points and networks, check signal strength, and view other diagnostics. For help, see “Checking 802.11 Network Status” on page 94. Note: If you choose Exit iConnect from the menu, the desktop icon disappears. To restore the iConnect desktop icon, warm boot the CN3.
Chapter 2 — Connecting and Configuring the CN3 4 Select your modem type. • If using an external modem connected to your CN3 with a cable, choose Hayes Compatible on COM1 from the Select a modem drop-down list. • If using any type of external modem, choose the modem by name. If a listing does not exist for your modem, select Hayes Compatible on COM1. 5 Tap Next. 6 Enter the access phone number and then tap Next.
Chapter 2 — Connecting and Configuring the CN3 To create a VPN server connection to work 1 Tap Start > Settings > Connections. 2 Under My Work Network, tap Add a new VPN connection. 3 In the Name field, enter a name for the connection, such as your company name. 4 In the Host name / IP field, enter the VPN server name or IP address. 5 Select the VPN type of authentication to use with your CN3. If you are not sure which option to choose, check with your network administrator. 6 Tap Next.
Chapter 2 — Connecting and Configuring the CN3 8 Click Next. 9 Enter the User name, Password, and Domain (if provided by an ISP or your network administrator). 10 Tap Finish. 11 Insert the necessary equipment, such as a network card, into the CN3 and begin connecting. Configuring Wireless Security The CN3 provides four types of security for your wireless network: • Wi-Fi Protected Access 2 (WPA2™) • Wi-Fi Protected Access (WPA) • 802.
Chapter 2 — Connecting and Configuring the CN3 If you are using WPA-802.1x, WPA2-802.1x, or 802.1x security, this section also assumes that your authentication server and authenticators are properly configured. Note: Your security choice does not depend on your authentication server. For example, you can choose Funk security if you use Microsoft Active Directory® to issue certificates.
Chapter 2 — Connecting and Configuring the CN3 To select a Funk security profile 1 Start Intermec Settings. 2 Choose Communications > 802.11 Radio > Funk Security. 3 Tap a profile to expand it. 4 (Optional) In the Profile Label text box, enter a meaningful name for your profile. 5 Configure your security settings. For help, see the next sections. 6 Repeat Steps 3 through 5 for each profile you want to define.
Chapter 2 — Connecting and Configuring the CN3 b Tap User Name, enter your user name, and press Enter. c Tap User Password, enter your password, and press Enter. d For Validate Server Certificate, choose Yes and press Enter. Note: The correct date must be set on your CN3 when you enable Validate Server Certificate. If you choose TLS: a Load a user and root certificate on your CN3. For help, see “Loading a Certificate” on page 68. b Enter a User Name and Subject Name.
Chapter 2 — Connecting and Configuring the CN3 To configure 802.1x security with Funk security 1 Make sure the communications and radio parameters on your CN3 are configured. 2 Make sure Funk is selected as your security choice. 3 Start Intermec Settings. 4 Choose Communications > 802.11 Radio > Funk Security. 5 Select the profile you want to configure. 6 For Association, choose Open and press Enter. 7 For Encryption, choose WEP and press Enter.
Chapter 2 — Connecting and Configuring the CN3 To configure LEAP security 1 Make sure the communications and radio parameters on your CN3 are configured. 2 Make sure Funk is selected as your security choice. 3 Start Intermec Settings. 4 Choose Communications > 802.11 Radio > Funk Security. 5 Select the profile you want to configure. 6 For 8021x, choose LEAP and press Enter. 7 For Association, choose Open, WPA, WPA2, or Network EAP and press Enter.
Chapter 2 — Connecting and Configuring the CN3 for 64-bit WEP or a 13-byte value for 128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs. 10 For Transmit key, choose the key you want to use for transmitting data. 11 Save your settings and exit Intermec Settings. Selecting Microsoft as Your Security Choice The default security setting is Funk. If you want to use Microsoft security, you need to select it as your security choice.
Chapter 2 — Connecting and Configuring the CN3 4 For Infrastructure Mode, choose Infrastructure. 5 For Network Authentication, choose WPA. Data Encryption automatically defaults to TKIP. 6 For 802.1x Authentication, choose either MD5, TLS, or PEAP. 7 If you choose TLS: a Select Properties and tap the Run App button. The Auth. Settings dialog box appears. b Tap the Select button. c Select your certificate from the list and press Enter. The User Logon dialog box appears.
Chapter 2 — Connecting and Configuring the CN3 The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the authenticator. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the CN3 internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 7 Save your settings and exit Intermec Settings. To configure 802.
Chapter 2 — Connecting and Configuring the CN3 9 For Network Key Setting, choose Automatic. 10 Save your settings and exit Intermec Settings. To configure static WEP security with Microsoft security 1 Make sure the communications and radio parameters on your CN3 are configured. 2 Start Intermec Settings. 3 Choose Communications > 802.11 Radio > Microsoft Security. 4 For Network Authentication, choose Open. 5 For Data Encryption, choose WEP. 6 For Network Key Setting, choose Enter Key and Index.
Chapter 2 — Connecting and Configuring the CN3 Note: PFX encoded certificates are also supported. Tap the Import pfx button to import a PFX encoded certificate. 4 To import a root certificate: a Tap the <<< button next to the Import Root Certificate field to select the root certificate (DER-encoded .cer file) to import. b Click Import Root Cert to install the selected certificate.
Chapter 2 — Connecting and Configuring the CN3 d Tap OK. The Enrollment Tool message box appears telling you that the certificate has been added. e Tap OK to close the message box. Disabling Security If you choose not to use security with your wireless network, you can disable it on the CN3. Intermec recommends that you always set security in your network. To disable security 1 Start Intermec Settings. For help, see “Configuring the CN3 Parameters” on page 45. 2 Choose Communications > 802.
3 Developing and Installing Applications Use this chapter to understand the guidelines for developing applications for use on the CN3.
Chapter 3 — Developing and Installing Applications Developing Applications for the CN3 Use the Intermec Resource Kits to develop applications to run on the CN3. The Resource Kits are a library of C++, .NET, Java, and web components grouped by functionality that you can use to create applications for the computer. The Resource Kits are part of the Intermec Developer Library (IDL), and can be downloaded from the Intermec web site at www.intermec.com/idl.
Chapter 3 — Developing and Installing Applications Files copied to any of these locations are safe when you cold boot the computer as long as the AutoRun system is installed in the appropriate location. When AutoRun is installed on the computer, all .cab files in the CabFiles folder are automatically extracted after a cold boot. For more information about AutoRun, see the Intermec Developer Library Resource Kit Developer’s Guide.
Chapter 3 — Developing and Installing Applications Installing Applications Using Microsoft ActiveSync When you only have a few computers to update with applications, you can copy files using Microsoft ActiveSync. This procedure assumes that Microsoft ActiveSync is installed on your PC and is up and running. To install an application on the computer using ActiveSync 1 Connect to the CN3 via ActiveSync. For help, see “Connecting to a PC” on page 43. 2 Copy the .cab files from your development PC to the CN3.
Chapter 3 — Developing and Installing Applications HKEY_CURRENT_USER\Software\iConnect2\IConnect\Settings\ShowFTPMenu The iFTP menu is available the next time you start iConnect. To manage the state of the FTP server • Modify these existing registry keys: HKEY_CURRENT_USER\Software\iConnect2\IConnect\Settings\FtpAutoStart HKEY_CURRENT_USER\Software\iConnect2\IConnect\Settings\FtpHeartbeat where 1 = enable and 0 = disable.
Chapter 3 — Developing and Installing Applications AutoRun supports the following script commands in AutoRun.dat: AutoRun Script Commands Command Description EXEC Launches a specified program and waits for it to finish (up to 10 minutes) CALL Processes a specified file of commands and returns. CHAIN Processes a specified file of commands and does not return. AutoRun handles quoted file names for the first parameter, which allows you to specify path names or file names that contain white spaces.
Chapter 3 — Developing and Installing Applications try { System.Diagnostics.Process.Start("\\ProgramFiles\\ImageCapture \\ImageCapture.exe","\"\\Program Files\\MyApp\\ImageCapture_ Config.xml\""); } catch (Exception exception) { MessageBox.Show("Failed to execute \\ProgramFiles\\ImageCapture \\ImageCapture.exe” + "\r\n" + exception.
Chapter 3 — Developing and Installing Applications Field Definitions for ImageCapture_Config.xml (continued) Field Name Valid Values Description lightingCorrection True or false Default is true. If no value is provided, the application cannot change the lighting correction value. allowChanges True or false Default is true. When set to false, user cannot change the noise reduction setting. noiseReduction 0 to 9 Default is no value.
Chapter 3 — Developing and Installing Applications Field Definitions for ImageCapture_Config.xml (continued) Field Name Valid Values Description allowChanges True or false Default is false. When set to true, user can change the file format type. fileFormat BMP, JPEG Default is no value. If no value is provided, Image Capture does not change the file format setting. If no format is selected, the file is saved as a .bmp. allowChanges True or false Default is false.
Chapter 3 — Developing and Installing Applications Freeing Up Virtual Memory for Applications You can use the InstallSelect application to free up virtual memory and create more space to load and run custom applications. Note: InstallSelect is designed for use only by administrators, developers, integrators, or Intermec service representatives.
Chapter 3 — Developing and Installing Applications 5 Clear the check box for each component you do not want installed after a clean boot. For a description of each component, see the next table. 6 Tap Apply to start the clean boot. A confirming message appears. 7 Tap Yes to continue. The CN3 performs a clean boot. Only the components you selected are installed. InstallSelect Software Components Component Name Description Avalanche Enabler Enables the client to the Wavelink Device Management solution.
Chapter 3 — Developing and Installing Applications InstallSelect Software Components (continued) Component Name Description Image Capture Image Capture application and components. Supported by CN3s with the EA11 area imager. Power Profiler Power Profiler applet. GPS Applet iGPS Settings applet. Additional Files Microsoft C Runtime Library Depending on the options installed in your CN3, you may see other components available from the InstallSelect application.
Chapter 3 — Developing and Installing Applications To download the upgrade files 1 Open a web browser and go to www.intermec.com. 2 Choose Support > Downloads and choose these items: a In the Product Category list, choose Computers. b In the Product Family list, choose Handheld Computers. c In the Product list, choose CN3 Mobile Computer. 3 Click Submit. A list of downloadable software appears. 4 Look for the appropriate upgrade files in the OS/Firmware/ Drivers list, and click a filename to download it.
Chapter 3 — Developing and Installing Applications 5 Double-click the .exe file on your PC. An InstallShield application starts and walks you through the process of extracting the upgrade files to the default location. Note: Do not change the default location where InstallShield extract the files. The SmartSystems console requires the files to be in this location. 6 From the SmartSystems console, locate the device upgrade to install.
Chapter 3 — Developing and Installing Applications 2 Insert the miniSD card into the CN3. 3 Clean boot the CN3. For help, see “Clean Booting the CN3” on page 100. When the clean boot is complete, the CN3 warm boots to reset the configuration. 4 (Optional) Remove the miniSD card or delete the files on the miniSD card. During the clean boot, the files were copied from the miniSD card to the Flash File Store.
Chapter 3 — Developing and Installing Applications 86 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
4 Troubleshooting and Maintaining the CN3 If you encounter any problems while using the mobile computer, look in this chapter to find a possible solution. You will also find information on routine maintenance.
Chapter 4 — Troubleshooting and Maintaining the CN3 Calling Product Support If you cannot find the answer to your problem in the “Troubleshooting the CN3” section, you can visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support.
Chapter 4 — Troubleshooting and Maintaining the CN3 To find your operating system or SSPB version 1 Tap Start > Internet Explorer. 2 Tap the Intermec logo. The Intermec page appears and displays the software build information. Troubleshooting the CN3 If you send the CN3 in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Chapter 4 — Troubleshooting and Maintaining the CN3 Problems While Operating the CN3 Problem Solution You press the Power button and nothing happens. • Make sure the backlight is on. • Make sure you have a charged battery that is installed correctly. For help, see “Charging the Battery” on page 4. • Replace the battery with a charged battery. For help, see “Changing the Battery” on page 5. • Perform a warm boot or a cold boot. For help, see “Resetting the CN3” on page 97. The Battery status LED is on.
Chapter 4 — Troubleshooting and Maintaining the CN3 Problems With Wireless Connectivity Problem Solution When you turn on the computer after it was suspended for a while (10 to 15 minutes or longer), it can no longer send or receive messages over the network. Host may have deactivated or lost current terminal emulation session. In a TCP/IP direct connect network, turn off the “Keep Alive” message from host to maintain the TCP session while the computer is suspended.
Chapter 4 — Troubleshooting and Maintaining the CN3 Problems While Configuring 802.1x Security (continued) Problem Solution A network connection icon appears in the toolbar, but then disappears. The CN3 may not be communicating with the intended access point. Make sure the network name (SSID) on the CN3 matches the access point network name. Default network name is “INTERMEC.” The access point may not be communicating with server. Ensure the access point is turned on, properly configured, and has 802.
Chapter 4 — Troubleshooting and Maintaining the CN3 Problems Reading Bar Codes Problem Solution You cannot see a red beam of light from • You may be too far away from the bar code label. Try the imager when you press the Scan moving closer to the bar code label and scan it again. button and aim the imager at a bar • You may be scanning the bar code label “straight on.” code label. Change the scanning angle and try again. • The scanner hardware trigger might be disabled in Intermec Settings.
Chapter 4 — Troubleshooting and Maintaining the CN3 Checking 802.11 Network Status If you have trouble connecting to your 802.11 wireless network: • Make sure you have correctly set network parameters on the CN3. • Check your wireless security settings. Follow the next procedure to use iConnect to verify available access points and networks, check signal strength, and view other diagnostics.
Chapter 4 — Troubleshooting and Maintaining the CN3 4 Tap the Scan tab to view a list of available 802.11 networks. The list includes the signal strength, channel, and MAC address for each network. • Tap Scan to refresh the screen. 5 Tap the Supp tab to view radio supplicant information, including a list of supplicant events and authentication status. • To verify the settings for the currently active security profile, tap Configure Profile. The Profile Wizard for the active profile appears.
Chapter 4 — Troubleshooting and Maintaining the CN3 To run a ping test: a In the Host field, enter the IP address of the host. b From the Repetitions list, choose the number of times the CN3 will ping the host. c Tap Ping. The graph shows the amount of time it takes for the host to return the ping. Tap List to see this information in a list format. 7 Tap the RSSI tab to view the received signal strength of the host signal.
Chapter 4 — Troubleshooting and Maintaining the CN3 8 Tap the Conf tab to set up a log file that lists RSSI history. This screen includes the 802.11 radio driver version and available radio modes. To create a log file: a Check the Log to File check box. b (Optional) Change the sample period and number of samples displayed. c Tap Log File. The Save As screen appears.
Chapter 4 — Troubleshooting and Maintaining the CN3 • Cold booting the CN3 restarts the computer if the computer seems to be locked up, or if a warm boot has no effect. CN3 settings are saved, but transaction data may be lost after a cold boot. For more information, see “Cold Booting the CN3” later in this section. • Clean booting the CN3 erases the computer memory, including all applications and files. Use this method only if warm booting and cold booting the CN3 have no effect.
Chapter 4 — Troubleshooting and Maintaining the CN3 3 Use the stylus to press the Reset button on the back of the CN3. Reset button Locating the Reset Button on the CN3 Reset button Locating the Reset Button on the CN3e 4 Replace the battery. The CN3 cold boots. When the cold boot is complete, the Today screen appears. CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Chapter 4 — Troubleshooting and Maintaining the CN3 Clean Booting the CN3 A clean boot erases the memory in the mobile computer, including all applications and data files found in the ObjectStore, and loads only the default files and programs required by the CN3 operating system. If the CN3 seems to be locked up, try warm booting and then cold booting the computer. If neither method works, use a clean boot to get the CN3 up and running for further troubleshooting.
Chapter 4 — Troubleshooting and Maintaining the CN3 Cleaning the CN3 To keep the CN3 in good working order, you may need to clean the imager or camera window and the touch screen. Clean the window and the touch screen as often as needed for the environment in which you are using the CN3. To clean the CN3, use a solution of ammonia and water. There are no user-serviceable parts inside the CN3. Opening the CN3 voids the warranty and may cause damage to the internal components.
Chapter 4 — Troubleshooting and Maintaining the CN3 102 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
A Specifications 103
Appendix A — Specifications Physical and Environmental Specifications CN3 Physical Dimensions (excluding overmold) Length: Width: Height: Weight: 16.0 cm (6.3 in) 8.1 cm (3.2 in) 2.8 cm (1.1 in) with standard battery Without WAN option: 0.40 kg (14 oz) WAN CN3 w/standard battery: 0.43 to 0.45 kg (15 to 16 oz) WAN CN3 w/extended battery: 0.45 to 0.48 kg (16 to 17 oz) CN3e Physical Dimensions (excluding overmold) Length: Width: Height: Weight: 19.5 cm (7.7 in) 8.1 cm (3.2 in) 3.3 cm (1.
Appendix A — Specifications Electrical Specifications External charge power: 5 V +/- 5% @3.5 A max (18 W max) Environmental Operating temperature: -10° to 50°C (14° to 122°F) (CN3) -20° to 60°C (-4° to 140°F) (CN3e) Storage temperature: -20° to 70°C (-13° to 158°F) Humidity: 5% to 95% non-condensing Rain and dust resistance: IP54 compliant (CN3) IP64 compliant (CN3e) Drop specifications: Multiple 1.
Appendix A — Specifications EA11 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" in 10" 25 8" 20 Data Matrix 7.5 mils 6" 15 PDF417 6.6 mils 4" 10 2" 5 0" 0 2" 5 10 4" 0.125mm / 5mils 6" 15 0.25 mm / 10 mils 20 100% contrast UPC EAN 8" 0.5 mm / 20 mils 25 10" cm 0 10 20 30 40 50 EA11 Standard Minimum Reading Distances With 0.
Appendix A — Specifications Accessories All of the accessories listed below work for both the CN3 and CN3e models unless otherwise noted. AA12 Ethernet Adapter Use the Ethernet adapter with the AD10 single dock to convert USB host to Ethernet connection. AA13 Modem Adapter Use the modem adapter with the AD10 single dock to convert USB host to a landline modem connection. AA15 Audio Adapter Use the audio adapter to connect your audio headset to the CN3.
Appendix A — Specifications AD12 Charge-Only Multidock Use the charge-only multidock to hold up to four CN3s with batteries installed, charge batteries, and provide power to CN3s. AV6 Vehicle Dock Use the vehicle dock to hold and charge the CN3 while using it on a vehicle. AV9 Vehicle Dock Use the vehicle dock to hold and charge the CN3e while using it on a vehicle. AR1 Magnetic Card Reader The magnetic card reader provides magnetic stripe reading capability to the CN3.
B Default Settings 109
Appendix B — Default Settings Default Configuration The following tables list the default values of the configuration commands supported on the CN3. If you restore the CN3 to factory default settings, the CN3 uses these values. The commands are grouped by function and reflect the organization of Intermec Settings. For detailed information on most of the commands, see the Intermec Settings Command Reference Manual, available from the Intermec web site at www.intermec.com.
Appendix B — Default Settings Symbology (continued) Default Value GS1 DataBar Limited Disable GS1 DataBar Omni-Directional Disable Interleaved 2 of 5 Disable JapanPost Disable Matrix 2 of 5 Disable Maxicode Disable Micro PDF417 Disable MSI Disable PDF417 Enable Planet Disable Plessey Disable Postnet Disable QR Code Disable Standard 2 of 5 Disable Telepen Disable TLC 39 Disable Symbology Option Default Value Preamble None (disabled) Postamble None (disabled) Global Sym
Appendix B — Default Settings 112 Decode Security Setting Default Value Consecutive Data Validation 0 Identical Consecutive Timeout 300 ms Different Consecutive Timeout 0 Center Decoding Disable Center Decoding Tolerance Disable Virtual Wedge Setting Default Value Virtual Wedge Enable Grid Null Magstripe reader Default Value Magstripe Reader Disable CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Appendix B — Default Settings RFID RFID Setting Default Value RFID Service Enable Application Connection Setting Default Value Allow External BRI Connections Enable BRI TCP Port 2189 BRI Heartbeat Disable Trigger Management Disable Enable Logging Disable Reader 1 Setting Default Value Enable Reader Disable Connected Disable Reader Model IP30 Trigger Management Disable Enable Logging Disable RFID Module Setting Default Value Tag Type EPC Class 1 Gen2 Dense Reader Mode Disabl
Appendix B — Default Settings RFID Module Setting (continued) Default Value Read Tries 3 Write Tries 3 Initialization Tries 1 Lock Tries 3 Select Tries 1 Unselect Tries 1 Initial Q 4 Field Strength dB 30 Session 2 Enable Antenna Port 1 Enable Enable Antenna Port 2 Disable Enable Antenna Port 3 Disable Enable Antenna Port 4 Disable Communications 114 Communications Setting Default Value Device Name CN3 Bluetooth Setting Default Value Bluetooth Power Off Bluetooth Discove
Appendix B — Default Settings Funk Security Setting Default Value Active Profile 1 Profile Label Profile_1 Network Type Infrastructure Channel 3 SSID INTERMEC Power Mode Enabled (Fast PSP) 8021x None Association Open Encryption None Pre-Shared Key Null Transmit Key Key1 Prompt for Credentials Enable User Name anonymous User Password anonymous Inner Authentication-TTLS MS-Chapv2 Anonymous name anonymous Inner EAP EAP/MDS Inner Authentication-PEAP EAP/MS-Chapv2 Subject Na
Appendix B — Default Settings 116 Ethernet Adapter Settings Default Value DHCP Enable DHCP Client Identifier Null Primary DNS 0.0.0.0 Secondary DNS 0.0.0.0 Primary WINS 0.0.0.0 Secondary WINS 0.0.0.
Appendix B — Default Settings PSK Setting (continued) Default Value Serial Port Baud Parity Data Bits Stop Bits Flow Control Protocol EOM1 EOM2 SOM Reader Command LRC Handshake 115200 Even 7 Data Bits 1 Stop Bit No Flow Control Configurable \x03 \xFFFFFFFF \x02 Enable w/o TMF Disable Disable Device Settings Device Setting Default Value Date Null Time Null Adjust for Daylight Time Disable Good Read Beep One Beep Good Read LED On Beeper Volume Medium Display Setting Default Value Backlight
Appendix B — Default Settings Power Management Setting Default Value Battery Power Device Turns Off After Screen Turns Off After 2 min 1 min External Power Device Turns Off After Screen Turns Off After Disable Disable Device Monitor Device Monitor Setting Default Value Poll Period 1 min Threshold Values Backup Battery Charge Remaining Main Battery Charge Remaining Storage Load Memory Load 10 10 90 90 Core Messaging Service 118 Core Messaging Service Setting Default Value Associated Server I
C Keypads and Keystrokes 119
Appendix C — Keypads and Keystrokes Standard Characters Use the following tables to learn how to enter standard and other available characters and functions with the keypad. If there is no sequence of keystrokes for a particular character or function, it is only available through the soft input panel (SIP), which can be accessed by tapping the keyboard icon on the touch screen.
Appendix C — Keypads and Keystrokes Alphanumeric Characters (continued) Character s t u v w x y z A B C D E F G H I J K L M N O Numeric Keypad 10-Key Keypad QWERTY Keypad Alphabetic Keypad c7777 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 c1444 c15 c155 c1555 c16 c166 c1666 c1111 c2 c22 c222 c3 c33 c333 c3333 c78 c788 c7888 c79 c799 c7999 c74 c744 c7444 c75 c755 c7555 c76 c766 c7666 S T U V W X Y Z ]A ]B ]C ]D ]E ]F ]G ]H ]I ]J ]K ]L ]M ]N ]O S T U V W X Y Z ]A ]B ]C ]D ]E
Appendix C — Keypads and Keystrokes Alphanumeric Characters (continued) Character P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 122 Numeric Keypad 10-Key Keypad QWERTY Keypad Alphabetic Keypad c17 c177 c1777 c17777 c18 c188 c1888 c19 c199 c1999 c19999 0 1 2 3 4 5 6 7 8 9 c71 c711 c7111 c71111 c72 c722 c7222 c73 c733 c7333 c73333 0 1 2 3 4 5 6 7 8 9 ]P ]Q ]R ]S ]T ]U ]V ]W ]X ]Y ]Z bg bY bU bI bH bJ bK bB bN bM ]P ]Q ]R ]S ]T ]U ]V ]W ]X ]Y ]Z bg bJ bK bL bP bQ bR bV bW bX CN3 Mobile Computer User’s M
Appendix C — Keypads and Keystrokes Other Available Characters The next table lists both characters printed on the keypad overlays and hidden characters not printed on the overlays.
Appendix C — Keypads and Keystrokes Other Available Characters and Functions (continued) To Enter Numeric Keypad 10-Key Keypad QWERTY Keypad Alphabetic Keypad _ (underscore) N/A N/A BackTab bj c1 e b3 b| c b1 c0 bj c7 e b9 b| c b7 c0 ]bG bj b] e bO bP ] bW s ]bU bj b] e ) k ] ( s CapsLock Enter Application Softkey 2 ok Shift Application Softkey 1 Space Characters not available from the keypads are: • Left and right bracket ([ or ]) • Left and right curly bracket ({ or }) • Semicolon (;)
Appendix C — Keypads and Keystrokes To type language-specific characters on the CN3e numeric keypad 1 Press c c to lock the green modifier key. 2 Type the parent character. 3 Press . to cycle through the variant characters until you find the character you want. For more information, see the next table. 4 Press c to unlock the green key. To type language-specific characters on the QWERTY and alphabetic keypads 1 Type the parent character. 2 Press b 3 b to lock the orange modifier key.
Appendix C — Keypads and Keystrokes Language-Specific Characters (continued) 126 Parent Character Variant Characters n ñ N Ñ o ò ó ô õ ö ő ø œ O Ò Ó Ô Õ Ö Ő Ø Œ p Þ ¶ P þ ¶ r ® R ® s ş š ß S Ş Š ß t ţ T Ţ u ù ú û ü ű U Ù Ú Û Ü Ű y ý Y Ý z ź ż Z Ź Ż CN3 Mobile Computer User’s Manual for Windows Mobile 6.
I Index 127
Index Numerics 10-key keypad keypresses, listed 120–125 802.11d support 3 802.
Index Bluetooth Audio enabler 53 booting the CN3 97 clean 100 cold 98 warm 98 C calibrating screen 22 calling product support 88 camera 32 cleaning window 101 configuring 33 capacitor, super, as backup power 5 card, miniSD, using to install applications 74 cellular phone, using CN3 as 18, 44 making a call 45 mike and speaker, illustrated 18 power management profiles, described 11 vibrate, enabling 20 certificates, loading 68 characters, typing with keypad 15 alphabetic, list of 120 language-specific 124 pun
Index configuring the CN3 (continued) Ethernet 49 GPS 36 Intermec Settings 45–48 network communications 49 phone 44 power management profiles, selecting 10 power timeout values 11 security, wireless 59 SmartSystems console 46 vibrate mode 20 volume, for cell phone 18 volume, for general audio 19 WAN 44–45 connecting to PC with ActiveSync 43 console 46 D data collection settings, default 110 decode security settings, default 112 default settings 110–118 data collection 110 decode security 112 imager 111 mags
Index imager (continued) signature capture 32 ink capture, described 32 installing applications 73 battery 5 miniSD card 34 SIM card 34 InstallSelect described 80 using to free up memory 80 Intermec Product Support, contacting 88 Resource Kits, described 72 value-add functionality, described 82 Intermec Developer Library (IDL) 72 Intermec Settings described 45 menu items, hiding and restoring 48 SmartSystems console, opening from 46 using on CN3 47 Internet Explorer, using to find OS version 89 K keypads il
Index phone configuring 44 making a call 45 mike and speaker, illustrated 18 power management profiles, described 11 turning on with Wireless Manager 44 using 18 vibrate, enabling 20 physical specifications 104 Pictures & Videos, using to take pictures 33 pictures, storage location 33 power backlight settings 23 battery 4–12 battery life, maximizing 9 button 17 management profiles choosing 10 described 11 managing 9 timeout values, customizing 11 power adapter, for vehicle use 108 Power application, using t
Index SmartSystems Foundation (continued) Intermec Settings, using from console 46 Scan-to-Connect 43 upgrading CN3 83 where to download 43 SmartSystems Platform Bundle files, described 82 upgrading with miniSD card 84 specifications Bluetooth QD ID 104 electrical 105 environmental 105 hardware 104 imager reading distance 106 physical 104 power 105 regulatory approvals 105 standard communications 104 touch screen 104 wireless LAN 105 SSPB.
Index WPA-PSK security with Funk 61 with Microsoft 66 www.intermec.com downloads for CN3 82 Intermec Developer Library 72 Knowledge Central x manuals, downloading xi service locations x 134 SmartSystems Foundation 43 warranty information ix web support x www.windowsmobile.com 43 X XML, for Image Capture application 77, 79 CN3 Mobile Computer User’s Manual for Windows Mobile 6.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2010 Intermec Technologies Corporation. All rights reserved. CN3 Mobile Computer User’s Manual for Windows Mobile 6.
