70 Series Mobile Computer CK70, CK70NI, CK71, CK71NI, CN70, CN70NI, CN70e, CN70eNI User Manual
Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation.
Document Change Record This page records changes to this document. The document was originally released as Revision 001. Version Number Date Description of Change 005 11/2012 Added information to support firmware version 1.50: • CloneNGo application • New camera settings • SceneEditor application • EA30 imager extended reading range 004 2/2012 Revised information on ScanNGo bar codes. 003 12/2011 Added information on: • the flashlight feature. • the Carrier Selection application.
iv 70 Series Mobile Computer User Manual
Contents Contents Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Global Services and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Use the Imager as a Flashlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Read Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Insert a MicroSD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Install a MicroSD Card in a CN70 or CN70e . . . . . . . . . . . . . .
Contents Make a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Make an Emergency Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 4 Use the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 About the Color Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents About Network Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Configure 802.11a/b/g/n (Wi-Fi) Radio Communications . . . . . . . . . . . . . . . . . . . 83 Configure Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Configure Bluetooth Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 About Serial and USB Communications . . . . . . . . . . .
Contents Call Product Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Find Your Configuration Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Find Your Operating System Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Reset the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents B Keypads and Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Standard Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 CN70 Keypads and Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 CN70e Keypads and Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety cautions.
Before You Begin Visit the Intermec technical knowledge base (Knowledge Central) at www.intermec.com and click Support > Knowledge Central to review technical information or to request technical support for your Intermec product. Send Feedback Your feedback is crucial to the continual improvement of our documentation. To provide feedback about this manual, please contact the Intermec Technical Communications department directly at TechnicalCommunications@intermec.com. Telephone Support In the U.S.A.
Before You Begin To download documents 1 Visit the Intermec website at www.intermec.com. 2 Click the Products tab. 3 Using the Products menu, navigate to your product page. For example, to find the CN70 computer product page, click Computers > Handheld Computers > CN70. 4 Click the Manuals tab. If your product does not have its own product page, click Support > Manuals. Use the Product Category, the Product Family, and Product to find your documentation.
Before You Begin 6152370; 6155490; 6158661; 6164542; 6164545; 6173893; 6195053; 6234393; 6234395; 6244512; 6249008; 6328214; 6330975; 6345765; 6356949; 6367699; 6375075; 6375076; 6375344; 6431451; 6435411; 6484944; 6488209; 6497368; 6532152; 6538413; 6539422; 6621942; 6641046; 6681994; 6687403; 6688523; 6732930 There may be other U.S. and foreign patents pending.
1 About the Computer Features This chapter introduces the 70 Series Mobile Computers with Windows® Embedded Handheld operating system. Use this chapter to learn about the basic features and functions of each computer, as well as the available accessories for it.
Chapter 1 — About the Computer Features About the 70 Series Mobile Computers The ergonomically designed Intermec 70 Series Mobile Computers are built on the Microsoft Windows Embedded Handheld operating system. They are lightweight, easy-to-use, and run most software developed for the Windows Embedded platform, including standalone, client-server, and browser-based applications. The 70 Series family of computers consists of four different models: the CN70, CN70e, CK70 and CK71.
Chapter 1 — About the Computer Features CN70 Back View Imager Camera Speaker port Battery IrDa port CK70 and CK71 Front View Cell phone speaker Good read LED Notification LED Battery status LED Scan button On/off button Microphone 70 Series Mobile Computer User Manual 3
Chapter 1 — About the Computer Features CK70 and CK71 Back View Imager Camera Imager Camera Left speaker port IrDA port Battery Left speaker port IrDA port Battery What’s New in This Release This version of the user manual supports firmware version 1.50 and includes information about these new features: • • • • 4 Intermec CloneNGo is a peer-to-peer device management application that ships on every computer and simplifies the process of configuring multiple computers.
Chapter 1 — About the Computer Features Overview of 70 Series Features The 70 Series includes these standard features: • • • • • • • • • • EA30 area imager that can read bar codes and capture images (CK71 only) Choice of EA30, EX25, or EV12 imagers Multi-processor architecture with 512 MB DRAM and 1G Flash CDMA, UMTS, or Flexible Network Radio capability (not available on CK71) 802.
Chapter 1 — About the Computer Features About the Status LEDs Use the following illustrations and table to understand the status LEDs on your computer. All six status LEDS are not available on every 70 Series computer. For example, the QWERTY versions of the CN70 and CN70e do not have a Green key status LED.
Chapter 1 — About the Computer Features Location of the CK70 and CK71 Status LEDs Notification LED Good Read and Ready-to-Work status LED Orange key status LED Battery status LED Green key status LED Shift key status LED (CK70 alphanumeric and CK71 function numeric) Shift key status LED (CK70 numeric and CK71 alphanumeric) Status LED Descriptions LED Color Description Notification Amber This LED is user-programmable. Good Read Green The computer successfully decoded a bar code.
Chapter 1 — About the Computer Features LED Color Description Key Status Green The Green function key is enabled. Orange The Orange function key is enabled. Red The Shift key is enabled. Shift 70 Series Accessories The 70 Series computer ships with a battery. All other accessories are sold and ordered separately. For help, contact your local Intermec sales representative.
Chapter 1 — About the Computer Features Accessory Description DX2 Dual Dock and DX4 Quad Dock. The DX2 and DX4 are available in charge-only and Ethernet configurations. Use these charger bases with the: • Computer cup to charge batteries while they are installed in the computer. • Battery cup to charge two batteries. Ethernet Snap-On Adapter Use the Ethernet adapter to be able to connect the computer to an Ethernet network.
Chapter 1 — About the Computer Features About Language Provisioning If your 70 Series computer includes language provisioning, you are prompted to select a language provision when the computer starts for the first time. It may take up to 15 minutes to load your language.
Chapter 1 — About the Computer Features Charge the Battery You need to fully charge the battery before using your computer for the first time. Use one of the charging accessories listed in the next table to charge the battery.
Chapter 1 — About the Computer Features Detach the Handstrap From a CK70 or CK71 4 Make sure the computer is in hibernate mode and the screen is off. 5 Remove the battery. • 12 On the CN70 or CN70e, push the battery release toward the bottom of the computer until the battery releases and then lift it away from the computer.
Chapter 1 — About the Computer Features • On the CK70 or CK71, push the battery release toward the top of the computer until the battery releases and then lift it away from the computer. 6 Insert the top end of a fully charged battery into the computer, and press down firmly on the bottom of the battery. Make sure that the battery release is fully engaged. About Battery Status Use the battery icon on the Title bar to see the power status of your battery.
Chapter 1 — About the Computer Features Battery Icon Status Battery is critically low. You need to replace the battery now. Battery is charging. The battery is not installed. You can also use the battery status LED to see the charging status of your battery. Battery status LED Battery Status LED Descriptions 14 LED State Description Steady green The computer is connected to a charger and the battery is more than 95% charged. Blinking red The battery is very low.
Chapter 1 — About the Computer Features About Battery Life and Conservation Batteries that are stored outside the computer for long periods of time slowly discharge. Intermec recommends storing the battery in a charger to maintain battery performance. Battery Conservation Tips When You Want To: Do This to Save Battery Power: Use the computer and the Low • Connect the computer to an external Battery status icon appears or the power source. Battery light comes on.
Chapter 1 — About the Computer Features About the Keypad The CN70 comes with either a QWERTY keypad or a numeric keypad. The CN70e comes with either a QWERTY numeric keypad, a phone-style numeric keypad (1-2-3 digits across the top), or a calculator-style numeric keypad (7-8-9 digits across the top). The computer has an ambient light sensor that detects low light and turns on the keypad backlight. By default, the keypad backlight is enabled in low light conditions.
Chapter 1 — About the Computer Features CN70 Numeric Keypad Esc 1 Caps 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ 0 Space Enter CN70e QWERTY Numeric Keypad 70 Series Mobile Computer User Manual 17
Chapter 1 — About the Computer Features CN70e Calculator-Style Numeric Keypad CN70e Numeric Keypad 18 70 Series Mobile Computer User Manual
Chapter 1 — About the Computer Features The CK70 comes with either a large alpha or an alphanumeric keypad. The CK71 comes with either a numeric function keypad or an alphanumeric keypad. The computer has an ambient light sensor that detects low light and turns on the keypad backlight. By default, the keypad backlight is enabled in low light conditions. You can disable the keypad backlight to conserve power. Use Intermec Settings to configure the backlight.
Chapter 1 — About the Computer Features CK70 Alphanumeric Keypad Esc Alt F6 Send 1 F1 F7 End 2 3 Insert F2 Delete 4 5 6 7 8 9 F8 F3 F9 0 F4 Enter F10 F5 F11 A F17 G F23 20 Ctrl F12 B F18 H F13 C F19 Space F14 D F20 F15 E F21 F16 F F22 I J K L F24 M N O P Q R S T U V W X Y Z 70 Series Mobile Computer User Manual
Chapter 1 — About the Computer Features CK71 Numeric Function Keypad View Insert Fld- Fld+ View SysRq Return Page Fld Exit Enter A PrvScr B 7 D Delete PA1 Roll 9 F 5 H 1 Home C NxtScr 8 E 4 G Roll PA2 Attn I Esc PA3 3 Space K Return 0 L F13 F1 P F17 F5 T F21 F9 M F14 Enter N F2 Q F18 F22 F15 F3 R F6 U Reset 6 2 J Clear F16 F4 F19 F7 V O S F20 F8 F23 W F24 F10 F11 F12 X Y Ctrl 70 Series Mobile Computer User Manual Z Alt 21
Chapter 1 — About the Computer Features CK71 Alphanumeric Keypad View Alt Reset Page Fld Exit Esc F6 PA1 PrvScr 7 F1 4 F2 Roll Delete 9 5 6 2 3 F9 Autolog Return 0 F4 Enter F10 EEOF F5 F11 Attn A Ctrl F12 B F13 C Space F14 Dup F15 Erase F16 Find D E F17 FldMk F18 Home F19 Hex F20 G H I F23 Menu F24 NewLn Mode F F21Keypd F22 J K L Print SysRq Remove Q R W X M N O P S T U V ? Y 22 Clear Help Fld+ 1 F3 NxtScr 8 F7 PA2 Insert F8 PA3 Fld- Roll
Chapter 1 — About the Computer Features Enter Characters on the QWERTY Keypad You need to use the orange modifier key b and the Shift key y to access all characters and functions on the QWERTY keypad. To type a character: • Press the key for that character. To type a character or access a function on the overlay: • Press b and then press the key for the character or function.
Chapter 1 — About the Computer Features For example, in the upper right corner of the 2 key there are the letters “ABC”: • To type “c”, press c 2 2 2. • To type “C,” press c 1 and then press c 2 2 2. Note: On the calculator-style keypad, the 2 is replaced by the 8. To only type letters: Press c c to lock the green modifier key, and then press the key one to four times depending on the position of the letter.
Chapter 1 — About the Computer Features About the Power Button When you press the Power button, a dialog box with a list of power options appears. If you do not select a power options setting, the currently selected action (the button outlined in bold) occurs after the timeout. The Intermec Power Options Default Screen Note: The Real Time Clock (RTC) persists through all of the power options as long as it receives power from the Real Time Clock battery.
Chapter 1 — About the Computer Features Option Description Suspend Medium power saving mode. The computer powers off all radios and internal devices not involved in saving the system state, but the phone stays on to receive calls. This option is the default setting. You can wake the computer by pressing the Power button, pulling the scanner trigger, receiving a call, scheduling an event such as an alarm, or by connecting external power.
Chapter 1 — About the Computer Features Configure the Screen Backlight The display has an ambient light sensor that automatically adjusts the backlight intensity to conserve power and ensure the display is readable. By default, the screen turns off when there is no activity with the computer. Press a key or tap the screen to resume activity. You can configure the screen backlight to turn off. 1 Tap Start > Settings > Power. 2 Tap Advanced on the horizontal scroll bar.
Chapter 1 — About the Computer Features You can adjust the volume settings using Intermec Settings or the horizontal scroll menu. 1 Tap the Volume icon at the top of the screen, and then tap the volume icon on the horizontal scroll menu. 2 Use your stylus or the u and d keys to adjust the volume slider to the volume you want, select Vibrate, or select Off. About the Imager The computer ships with an internal imager. You can use the imager as a flashlight or to read bar codes.
Chapter 1 — About the Computer Features Read Bar Codes Depending on the imager model in your computer, you can read 1D and 2D bar code symbologies, composite symbologies, and postal codes. You can also connect the computer to cordless scanners (like the SF51 and SR61) through Bluetooth communications or tethered scanners (like the SR30 and SR61T) through the RS-232 adapter. For help, see “Connect to a Bluetooth Scanner” on page 85 and “Connect to a Tethered Scanner” on page 89, respectively.
Chapter 1 — About the Computer Features Scanning With the EA30 Imager 5 Use the laser pointer as a guide and aim toward the middle of the bar code. Make sure that the illumination beam or frame covers the bar code you are trying to decode. When the computer successfully reads a bar code label, you hear a high beep, and the Good Read LED turns on briefly. 6 Release the Scan button. Insert a MicroSD Card You can use a microSD™ card to increase file storage and install software.
Chapter 1 — About the Computer Features 3 Remove the two Phillips screws and open the card access door. 4 Slide the SIM card door to the left to unlock it and open the door.
Chapter 1 — About the Computer Features 5 Slide the microSD card door towards the top of the computer to unlock it and open the door. 6 Slide the microSD card into place. 7 Close the microSD card door and slide it towards the bottom of the computer to lock it in place. 8 Close the SIM card door and slide it to the right to lock it in place. 9 Close the card access door and replace the two screws. 10 Install the battery.
Chapter 1 — About the Computer Features 11 Attach the handstrap. 12 Press the Power button. The computer cold boots. Install a MicroSD Card in a CK70 or CK71 You need a Phillips screwdriver to install the microSD card. 1 Press the Power button to turn off the computer. 2 Remove the handstrap. 3 Remove the two screws that attach the interface adapter cover to the back of the computer.
Chapter 1 — About the Computer Features 4 Slide the SIM card door to the left to unlock it and open the door. 5 Slide the microSD card door towards the top of the computer to unlock it and open the door.
Chapter 1 — About the Computer Features 6 Slide the microSD card into place. 7 Close the microSD card door and slide it towards the bottom of the computer to lock it in place. 8 Close the SIM card door and slide it to the right to lock it in place. 9 Replace the interface adapter cover and attach with the two screws removed in Step 2. 10 Install the battery. Press down firmly on the bottom of the battery, and make sure that the battery release tab is fully engaged. 11 Reattach the handstrap.
Chapter 1 — About the Computer Features Use Microsoft ActiveSync to Transfer Files You can use Microsoft ActiveSync (Windows XP or earlier) or Windows Mobile Device Center (Windows Vista or Windows 7) to establish a connection between your computer and a PC. After you connect to your PC, you can transfer files, synchronize files, remotely debug, and perform other device management activities. ActiveSync and Windows Mobile Device Center are free applications available from the Microsoft website at www.
Chapter 1 — About the Computer Features Use the Computer as a Mass Storage Device You can connect the 70 Series computer as a mass storage device to your desktop PC. When connected as a mass storage device, you can easily copy files to and from the mobile computer. 1 Go to www.datalight.com and download the Reliance Nitro Windows Driver (RNWD). You need to login before you can download the driver. 2 Connect the mobile computer to your desktop PC using a USB cable.
Chapter 1 — About the Computer Features 38 70 Series Mobile Computer User Manual
2 About the User Interface and Intermec Applications Use this chapter to learn about the Windows Embedded Handheld user interface and how to interact with the screen. You can also use this chapter to learn about the Intermec applications on your computer, as well as additional Intermec applications you can download.
Chapter 2 — About the User Interface and Intermec Applications About the User Interface The user interface for the Windows Embedded Handheld 6.5 operating system is different from previous versions of Windows Mobile. The interface is touch-friendly and easy to navigate. Use the following sections to understand how to interact with Windows Embedded Handheld 6.5. About the Home Screen When you turn on your mobile computer, the Home screen is the first screen that appears.
Chapter 2 — About the User Interface and Intermec Applications The horizontal scroll bar also replaces tabs within Windows screens and allows for easier navigation. Clock & Alarms Screen With Horizontal Scroll Bar Use the Tile bar to navigate between screens and within applications. The icons available on the Tile bar change depending on the application you are using. Interact with the Screen The Windows Embedded Handheld 6.
Chapter 2 — About the User Interface and Intermec Applications Title Bar Status Icons Tappable icons in the Title bar immediately show you the status of your network, your phone, the volume, the battery, and the time. Use the following table to understand what the icons mean. Title Bar Status Icon Descriptions Icon Description You have a new notification. You have a new text message. You have a new email message. You have a new instant message. You missed a call. The speakerphone is on.
Chapter 2 — About the User Interface and Intermec Applications Icon Description A UMTS network is available. Connecting to a UMTS network. A UMTS connection is active. A 3G+ network is available. An EDGE network is available. Connecting to an EDGE network. An EDGE connection is active. A GPRS network is available. Connecting to a GPRS network. A GPRS connection is active. An HSDPA network is available. Connecting to an HSDPA network. An HSDPA connection is active. Bluetooth is on.
Chapter 2 — About the User Interface and Intermec Applications Icon Description Connected to a wireless network, and other networks are detected. Information about a new wireless network is available. A network connection is active. A network connection is inactive. The phone has maximum signal strength. The phone has no signal. The phone capability is off. The phone has no service. The phone is searching for service. Data is being transferred. A voice call is in progress. A voice call is on hold.
Chapter 2 — About the User Interface and Intermec Applications Icon Description The battery has a low charge. The battery has a very low charge. The battery is attached to external power and is charging. No battery is installed in the computer. Call forwarding is on. Voice mail is off. GPS locator is off. GPS locator is on. Align the Screen You may need to align your screen if you tap on one area and it registers in a different part of the screen.
Chapter 2 — About the User Interface and Intermec Applications Intermec Applications Available on the Mobile Computer Icon Application Description Bluetooth Audio Use the Bluetooth Audio application to connect to a Bluetooth headset or hands-free device. For more information, see “Connect to a Bluetooth Audio Device” on page 88. Carrier Selection Use the Carrier Selection application to quickly change your network carrier. For more information, see “About Network Carriers” on page 56.
Chapter 2 — About the User Interface and Intermec Applications Icon Application Description ScanDiagnostic Use the ScanDiagnostic application to troubleshoot problems with the internal or external scanner. For more information, see “Use ScanDiagnostic to Troubleshoot the Scanner” on page 120. SceneEditor Use the SceneEditor application to modify predefined camera scenes or create new scenes. For more information, see “Configure Camera Scenes” on page 65.
Chapter 2 — About the User Interface and Intermec Applications About Features Demo Intermec Features Demo provides a simple way to explore the key features of your mobile computer. You will find applications that demonstrate scanning, document imaging, image capture, printing, and GPS functionality. Many of the applications that are part of Features Demo also have separate full-featured versions that you can download and license for your computer.
Chapter 2 — About the User Interface and Intermec Applications About Intermec Launcher Intermec Launcher is a Microsoft Windows application, designed for Intermec mobile computers, that provides a platform from which other applications may be launched while attempting to provide a locked-down environment. You can configure Intermec Launcher for your specific application requirements. You can download and use Intermec Launcher for a 60-day evaluation period.
Chapter 2 — About the User Interface and Intermec Applications 50 70 Series Mobile Computer User Manual
3 Use the Phone You can use the phone feature to make and receive telephone calls, as well as transmit data through cellular wide-area networks (WANs).
Chapter 3 — Use the Phone About the Phone The 70 Series mobile computer supports two types of cellular technology: • CDMA • UMTS Note: Your Flexible Network Radio mobile computer supports both CDMA and UMTS technology. Your Flexible Network Radio does not support Network Information and Time Zone (NITZ) messages to automatically set the system time. Phone features on the computer include a speaker and a microphone. You can also use a Bluetooth headset or hands-free kit.
Chapter 3 — Use the Phone 2 On the CN70 or CN70e: a Push the battery release tab forward until the battery releases, and lift the battery away from the computer. b Remove the two Phillips screws and open the card access door. 3 On the CK70, remove the two screws and lift the card access door away from the computer. 4 Slide the SIM card door to the left to unlock it and open the door.
Chapter 3 — Use the Phone 5 Slide the SIM card into the slot in the card access door. 6 Close the SIM card door and slide it to the right to lock it in place. 7 Close the card access door and replace the two screws. 8 Install the battery. Press down firmly on the bottom of the battery, and make sure that the battery release tab is fully engaged. 9 Press the Power button. The computer cold boots.
Chapter 3 — Use the Phone The carrier requires the Mobile Equipment Identifier (MEID) to start the activation process. You can find the MEID: • on a label located in the upper right corner of the battery compartment. • on the outside of the computer shipping box. • in the Version Information menu. Tap Start > Settings > Personal > Phone > Version Information tab. The activation process is slightly different for each CDMA carrier.
Chapter 3 — Use the Phone Start the Activation Wizard Depending on your wireless carrier, you may need to use the Windows Mobile Activation Wizard to activate your phone. 1 Tap Start > Phone, or tap the Phone button on the Tile bar. The phone application starts. 2 Tap Menu > Activation Wizard. Turn the Phone On and Off Before you can start using your phone, you need to enable it. You can use Wireless Center to enable and disable your phone, as well as Bluetooth and Wi-Fi communications.
Chapter 3 — Use the Phone Switch Network Carriers Use the Carrier Selection application to quickly change your WWAN radio network carrier on your Flexible Network Radio-enabled CN70, CN70e, or CK70 mobile computer. 1 Tap Start > Settings > Personal > Carrier Selection. 2 Select a Carrier and tap OK. A dialog box appears asking if you want to switch carriers. 3 Tap Yes to switch carriers. If the update is successful, the Carrier Selection screen appears and displays the updated carrier information.
Chapter 3 — Use the Phone Add the WWAN Connection If you are switching to a CDMA network, or switching from a CDMA network to a UMTS network, you must add the WWAN connection in Intermec Settings. 1 Tap Start > Settings > System > Intermec Settings > Communications > WWAN Radio. 2 Select Add New WWAN Connection. 3 Enter a Connection Name. In the Phone Number field, enter #777 and tap OK. The Manage WWAN Radio State screen appears.
Chapter 3 — Use the Phone 4 From Active Connection, select your Connection Name and Connect Now and tap OK. About the Network Connection Note: When you perform a clean boot, the selected carrier will default to generic UMTS. When you perform a clean boot, all user-created network connection entries are deleted, and only the generic UMTS remains.
Chapter 3 — Use the Phone Make a Phone Call After you activate your UTMS or CDMA phone, you are ready to start making phone calls. Note: Your Flexible Network Radio mobile computer is data only. You cannot make phone calls from the Flexible Network Radio. 1 Press Phone. 2 Tap the keys to enter the telephone number you want to call, and tap Talk. Make an Emergency Phone Call You can use the UMTS phone to make an emergency phone call even if the SIM card is missing.
4 Use the Camera You can use the color camera to take pictures and record videos.
Chapter 4 — Use the Camera About the Color Camera The camera and flash are located on the back of the computer. You run the Pictures & Videos application to access the camera features. Note: While the Pictures & Videos application is running, you cannot use the imager. In the Pictures & Videos application, you can: • • • • configure camera settings. take, view, and edit pictures. switch between Still (camera) mode and Video mode. record and launch video clips stored on the computer or a microSD card.
Chapter 4 — Use the Camera Setting Description Scenes Predefined scenes that optimize the camera settings for a specific environment: • • • • • • • • • • DocCap: Intermec document capture. Check: Capture images of paper checks. Night: Low light conditions. Cloudy: Cloudy or overcast conditions. Daylight: Bright sun. Van Interior: Dimly lit vehicle interior. Warehouse: Warehouse environment. Office Store: Office or store environment. Manual: Manually configure a specific set of camera settings.
Chapter 4 — Use the Camera Setting Description Exposure Exposure level of the image. Values are from -2.5 (darker, underexposed) to +2.5 (lighter, overexposed) in increments of 0.5. Default is 0. Brightness Brightness level of the image. Manual settings are from -4 (very dark) to +4 (very light) in increments of 1. Default is Auto. Contrast Amount of contrast in the image. Manual settings are from -4 (least contrast) to +4 (most contrast) in increments of 1. Default is Auto.
Chapter 4 — Use the Camera Configure the Camera Use the Pictures & Videos application to configure the camera. Note: You can also use Intermec Settings to configure some camera options. 1 Tap Start > Pictures & Video. 2 To enter Still mode, tap the Camera icon in the grid or the Camera button on the Tile bar. 3 Tap Menu. 4 Select a setting to configure. Configure Camera Scenes You can modify predefined camera scenes or create new scenes to further accommodate your specific needs.
Chapter 4 — Use the Camera Take a Picture When you take a picture, the image is saved as a .jpg file and stored in the /My Documents/My Pictures folder. 1 Tap Start > Pictures & Videos. 2 Tap the Camera icon in the grid or the Camera button on the Tile bar, or press Enter. 3 Using the screen as a viewfinder, move the camera until you have the image you want to take a picture of. 4 Hold the camera as still as possible, and press Enter to take and save the picture.
Chapter 4 — Use the Camera Save Pictures and Videos to a microSD Card Pictures and videos are automatically saved to the main memory on your computer. You can save your pictures and video to a microSD card to easily transport them to another device. 1 Install a microSD card. For help, see “Insert a MicroSD Card” on page 30. 2 Tap Start > Pictures & Videos. 3 Tap the camera icon. 4 Tap Menu > Options. 5 From the Save files to list, select SD card, and tap OK.
Chapter 4 — Use the Camera 68 70 Series Mobile Computer User Manual
5 Use GPS The 70 Series computer comes equipped with an integrated Global Positioning System (GPS) receiver if your computer has phone capability (WWAN radio). The GPS receiver can deliver standards-based National Marine Electronics Association (NMEA) data strings to GPS applications.
Chapter 5 — Use GPS About the Integrated GPS on Your Computer Intermec recommends that you use the GPS Intermediate Driver (GPSID) instead of directly accessing the GPS hardware. The GPSID is a Microsoft software component that interacts between applications and the GPS hardware. As a Microsoft software component, the GPSID: • • allows multiple applications to simultaneously access the GPS data stream. provides access to GPS data without requiring applications to recognize and parse NMEA syntax.
Chapter 5 — Use GPS 3 Tap Access in the horizontal scroll bar and select the Manage GPS automatically check box. 4 Tap OK. About the GPS Module Operating Modes The integrated GPS module has three operating modes: • Standalone • MS Assisted (Mobile Station Assisted) • gpsOneXTRA™ (UMTS computers only) In Standalone mode, the GPS module relies solely on GPS satellites to determine position.
Chapter 5 — Use GPS Qualcomm’s gpsOneXTRA Assistance technology provides enhanced operation for Standalone GPS. This option enables the UMTS-enabled computer to automatically download a small assistance data file from the XTRA servers through a brief internet access session. To use this option, you must have a valid and activated WAN data connection. Note: Internet connection fees may apply. Another option you can configure with iGPS is the fix interval.
6 Configure the Computer Use this chapter to learn about the available methods for configuring your mobile computer and how to use Intermec Settings. You can also use this chapter to learn how to configure network communications and wireless security.
Chapter 6 — Configure the Computer How to Configure the Computer You can configure many parameters on the computer such as the bar code symbologies it decodes or the network settings. The values you set for these parameters determine how the computer operates. There are several ways to configure the computer: • Directly on the computer. You can use Intermec Settings directly on the computer to change only the settings on that computer.
Chapter 6 — Configure the Computer Start Intermec Settings Intermec Settings is located on the System screen. • Tap Start > Settings > System > Intermec Settings. The Intermec Settings Main Menu appears. About the Structure of Intermec Settings Use the tables below to help find the parameters in Intermec Settings that you want to configure. Each table contains the parameters for one of the Intermec Settings Main Menu options.
Chapter 6 — Configure the Computer Data Collection Menu Data Collection Options Parameters You Can Configure Internal Scanner • • • • • • • • • • • • • • • • • Bluetooth Scanner Dock Tethered Scanner Camera Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Scanner port settings Imager settings Decode security Symbologies Scanner settings Camera settings Decode security BT-Configure on Connect Bluet
Chapter 6 — Configure the Computer Communications Options Parameters You Can Configure WWAN Radio • • • • • Serial Port Switch Serial port switch settings (IrDA, docking connector, and back interface) Add WWAN connection Edit WWAN connections Manage WWAN radio Carrier Selection WWAN information Device Settings Menu Device Settings Options Parameters You Can Configure Date and Time Date and time settings Good Read • • • • • • • • Sounds Internal scanner Tethered scanner Bluetooth scanner Beeper
Chapter 6 — Configure the Computer Device Settings Options Parameters You Can Configure Profile Settings Application Whether these parameter options appear in Profile Settings: • Camera • Power • Scanning Features Disabled by Policy None (read-only) Printer Menu Printer Options Parameters You Can Configure Printer (if connected through Bluetooth) Printer settings (Auto detect printer, memory, display, and so on) Note: The Printer menu displays settings for Bluetooth connected printers.
Chapter 6 — Configure the Computer Virtual Wedge Menu Virtual Wedge Options Parameters You Can Configure Enable Virtual Wedge Enable virtual wedge Bar Code Scanner Wedge Bar code scanner wedge settings (bar code scanner grid and label encoding) Magstripe Reader Wedge Magstripe Reader Grid Core Messaging Service Menu Core Messaging Service Options Parameters You Can Configure Server IP Server IP (read-only) Associated Server IP Associated server IP Broadcast Name Broadcast name Port Port (r
Chapter 6 — Configure the Computer Location Services Menu Location Services Options Parameters You Can Configure Server Server settings (port and enable server) Virtual GPS Virtual GPS settings For more information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual. Navigate in Intermec Settings You can easily navigate through the screens in Intermec Settings to find the parameter you need to configure.
Chapter 6 — Configure the Computer 3 From the Camera, Power, or Scanning submenu, check or clear the Display check box for the settings you want to have available to the end user. 4 Click OK to save your selection. Restore Default Settings to a Menu You can restore the items in a single menu to their default settings. 1 Navigate to the menu that you want to restore to defaults. 2 Tap Menu > Restore Menu Defaults. 3 When prompted, tap Yes to restore the menu default settings.
Chapter 6 — Configure the Computer Note: When you restore default settings in Intermec Settings, only the settings for visible items are restored to defaults. The settings for hidden menu items are not affected. Use Intermec Settings Remotely with SmartSystems Your mobile computer is SmartSystems-enabled, which lets you open Intermec Settings from the SmartSystems console to remotely configure all of your mobile computers.
Chapter 6 — Configure the Computer Configure 802.11a/b/g/n (Wi-Fi) Radio Communications Make sure all components with antennas are at least 30 cm (1 ft) apart when power is applied. Failure to comply could result in equipment damage. The mobile computer contains an 802.11 radio to transfer data using wireless communications and to support the TCP/IP network protocols. This section of the manual assumes that your wireless network is set up, including your access points. By default, the 802.
Chapter 6 — Configure the Computer 2 Connect the Ethernet cable from your network to the snap-on adapter or dock. Ethernet communications are automatically enabled on your mobile computer. 3 Make sure that your computer is communicating with the network. The network connection icon ( ) should appear on the title bar. Configure Bluetooth Communications Your mobile computer is Bluetooth™-enabled, which lets you connect to other Bluetooth devices, such as scanners, printers, or audio devices.
Chapter 6 — Configure the Computer 4 Tap OK. The Bluetooth radio maintains its state through a reboot or cold boot and maintains virtual COM ports. But, if you clean boot your computer you need to recreate pairings to devices. Connect to a Bluetooth Scanner You can connect the computer to an Intermec Bluetooth scanner, such as the SF51 or SR61. 1 Tap Start > Settings > System > Wireless Scanning.
Chapter 6 — Configure the Computer 2 Tap Add Device. 3 Select Quick Connect, Search, or Manual. Follow the onscreen instruction to add a wireless scanner.
Chapter 6 — Configure the Computer Connect to a Bluetooth Printer To configure your computer for Bluetooth wireless printing, you need to: • • create an application that opens the wireless printing COM port on your computer. For help, see the Bluetooth Resource Kit, which is part of the Intermec Developer Library (IDL), available from the Intermec website at www.intermec.com/idl. select the current wireless printer on your computer. For help, see the next procedure.
Chapter 6 — Configure the Computer Connect to a Bluetooth Audio Device Use the Bluetooth Audio enabler to discover, activate, and connect to Bluetooth audio devices such as a headset. This enables system sounds to be monitored through the headset. 1 Tap Start > Settings > System > Bluetooth Audio. 2 Tap Search to find your Bluetooth headset or hands-free device. 3 Select your device from the list and configure any settings. 4 Click OK when you are done.
Chapter 6 — Configure the Computer Connect to a Tethered Scanner Use this procedure to connect your mobile computer to an SR30, SR61T, or ASCII tethered scanner and enable RS-232 communications. 1 Tap Start > Settings > System > Intermec Settings > Communications > Serial Port Switch. 2 Select Standard docking and IrDA and tap OK. If the serial port switch is set to one of the other options, you need to select Standard docking and IrDA and then save and reboot the computer before you proceed.
Chapter 6 — Configure the Computer 3 Enter a name for the connection, such as “ISP Connection.” 4 If you are using an external modem connected to your mobile computer with a cable, select Hayes Compatible on COM1 from the Select a modem list. 5 Tap Next. 6 Enter the access phone number and then tap Next. 7 Enter the User name, Password, and Domain (if provided by an ISP or your network administrator). 8 Tap Finish. 9 On the Connections screen, tap Advanced on the horizontal scroll. 10 Tap Dialing Rules.
Chapter 6 — Configure the Computer Create a VPN Server Connection You can create a Virtual Private Network (VPN) connection to securely connect to servers, such as a corporate network, through the Internet. Before you can create a VPN connection, you need this information from your network administrator: • User name • Password • Domain name • TCP/IP settings • Host name or IP address of the VPN server After you have located this information, you can create a VPN server connection.
Chapter 6 — Configure the Computer About Wireless Security The computer provides five types of security for your wireless network: • Wi-Fi Protected Access 2 (WPA2™) • Wi-Fi Protected Access (WPA) • • 802.1x LEAP • WEP This section explains how to configure wireless security on your mobile computer. Intermec recommends that you implement WPA2 security using PSK (Personal) or 802.1X (Enterprise) key management as appropriate.
Chapter 6 — Configure the Computer • If you are primarily using the computer to connect to Wi-Fi hotspots, you may want to use Microsoft security. To use Microsoft security, you need to select it as your security choice. For help, see “Select Microsoft as Your Security Choice” on page 97. Select a Funk Security Profile You can define up to four profiles for Funk security. Different profiles let your computer communicate in different networks without having to change all of your security settings.
Chapter 6 — Configure the Computer 5 Select the profile you want to configure. 6 For Association, select WPA or WPA2. Encryption automatically defaults to TKIP or AES, respectively. 7 For 8021x, select TTLS, PEAP, EAP-FAST, or TLS. 8 If you selected TTLS, EAP-FAST, or PEAP: a For Prompt for Credentials, select Enter credentials now. b Enter a User Name and User Password. c For Validate Server Certificate, select Yes.
Chapter 6 — Configure the Computer 8 For Pre-Shared Key, enter the pre-shared key or passphrase. The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the access point. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the 70 Series internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 9 Save your settings. Configure 802.
Chapter 6 — Configure the Computer 10 If you select TLS: a Load a user and root certificate on your computer. For help, see “Load a Certificate” on page 102. b For Validate Server Certificate, select Yes. c Enter a User Name and Subject Name. 11 Save your settings. Configure LEAP Security with Funk After you configure the communications and radio parameters on your mobile computer and select Funk as your security choice, you can configure LEAP. 1 Start Intermec Settings. 2 Select Communications > 802.
Chapter 6 — Configure the Computer 5 Select the profile you want to configure. 6 For Association, select Open. 7 For Encryption, select WEP. 8 For 8021x select None. 9 Define a value for the keys you want to use. You can define up to four keys (Key 1 through Key 4). Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for 128-bit WEP.
Chapter 6 — Configure the Computer With Microsoft as your security choice, you can configure: • WPA or WPA2 • 802.1x • Static WEP Select Microsoft Security Use the following procedure to select Microsoft security. 1 Start Intermec Settings. For help, see “Configure the Computer” on page 73. 2 Select Communications > 802.11 Radio > Security Choice. 3 From the Security Choice list, select Microsoft Security.
Chapter 6 — Configure the Computer 7 If you selected TLS: a Load a user and root certificate on your computer. For help, see “Load a Certificate” on page 102. b Select Properties. The Certificates dialog box appears. c Select the certificate you want to use from the list. The User Logon dialog box appears. d Enter a User Name and Domain and tap OK. e Tap OK to exit the Certificates dialog box. f Press OK to save the Microsoft Security settings.
Chapter 6 — Configure the Computer 6 For Pre-Shared Key, enter the pre-shared key or the passphrase. The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the authenticator. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the computer internally converts it to a pre-shared key. 7 Save your settings. Configure 802.1x Security with Microsoft Use the following procedure to configure 802.
Chapter 6 — Configure the Computer 9 If you selected PEAP: a Load a root certificate of the authentication server on your computer. For help, see “Load a Certificate” on page 102. b Press OK to save the security settings and the User Logon dialog box appears. c Enter a User Name, Password, and Domain. Select Save Password if you want to save the password for future authentication sessions. d Press OK to save the Microsoft Security settings. 10 For Network Key Setting, select Automatic.
Chapter 6 — Configure the Computer Use Open (No Security) Associations with Microsoft Use the following procedure to configure your mobile computer for open security using Microsoft WZC. 1 Start Intermec Settings. 2 Select Communications > 802.11 Radio > Microsoft Security. 3 For Network Authentication, select Open. 4 For Data Encryption, select Disabled. 5 Tap OK. Your settings are saved. Load a Certificate To use transport layer security (TLS) with WPA or 802.
Chapter 6 — Configure the Computer 3 Tap Communications > 802.11 Radio > Certificates. The Certificates screen appears. 4 To import a certificate chain: a Tap Import Certificates to install the selected certificate. b In the CertImportUI screen, tap the <<< button next to the Select pfx to import text field. c Select the root certificate from the list. d Tap Import Certificate. 5 To import user and root certificates from a Microsoft IAS server: a Tap Import Certificates. b Tap Web Enrollment.
Chapter 6 — Configure the Computer 104 70 Series Mobile Computer User Manual
7 Manage the Computer Use this chapter to learn how to remotely update, configure, and monitor your Intermec mobile computers. You will also find information on installing and developing software applications as well as how to upgrade the system software.
Chapter 7 — Manage the Computer Manage the Computer in Your Network When you have multiple mobile computers and peripherals in your network, it is essential to have an easy way to manage updates, configure all of the devices, and remotely troubleshoot problems. Intermec provides a free device management software platform called SmartSystems™ Foundation to help you manage your devices. You can also purchase third-party device management software through a vendor.
Chapter 7 — Manage the Computer Intermec SmartSystems Console Through the console, you can: • drag-and-drop configuration bundles, operating system updates, and firmware upgrades to multiple computers. • save configuration settings from a single device and deploy those settings to many devices simultaneously. • remotely change settings on SmartSystems-enabled computers and peripherals.
Chapter 7 — Manage the Computer Manage the Computer Using Third-Party Software You can use third-party software such as Wavelink Avalanche to centrally manage your Intermec devices. Device management software enables you to update software, increase security, track your assets, and troubleshoot devices remotely. You can download the Wavelink Enabler for the mobile computer from the Wavelink website. For more information, visit the Intermec website and search for Wavelink Avalanche or visit www.wavelink.
Chapter 7 — Manage the Computer • The non-volatile Flash File Store. Applications and data in the Flash File Store will persist through a clean boot. Note: The Flash File Store is erased if you reflash the operating system image. Files copied to any of these locations are safe when you cold boot the computer as long as the AutoRun system is installed in the appropriate location. When AutoRun is installed on the computer, all .cab files in the CabFiles folder are automatically extracted after a cold boot.
Chapter 7 — Manage the Computer 3 Reboot or cold boot the computer. 4 After the boot process is finished, browse to the .cab files and tap the files to install them. Install Applications Using a Storage Card Use a storage card to install applications on one computer at a time or if you have no network connection. 1 Copy your application file to the storage card. 2 Install the storage card in the mobile computer. 3 On the mobile computer, browse to the Storage Card folder and run your application.
Chapter 7 — Manage the Computer Update Individual or Multiple Computers Using the SmartSystems Console You can use the SmartSystems console to update the operating system or system software on your mobile computer. The console is part of SmartSystems Foundation and is available from the Intermec website. Before you can update your mobile computer, you need: • SmartSystems Foundation. To download SmartSystems Foundation, go to www.intermec.com/SmartSystems and click the Downloads tab.
Chapter 7 — Manage the Computer Note: The SmartSystems console indicates that your mobile computer is offline, by displaying a red stop symbol, until the computer reboots and reconnects to the system. Update Individual Mobile Computers Using a microSD Card You can transfer upgrade bundles from your desktop PC to your mobile computer using a storage card. Before you can update your mobile computer, you need: • the SmartSystems bundles you want to install.
8 Troubleshoot and Maintain the Computer If you encounter any problems while using the 70 Series computer, look in this chapter to find a possible solution. You will also find information on routine maintenance.
Chapter 8 — Troubleshoot and Maintain the Computer About the Intermec Dashboard The Intermec Dashboard is designed to provide proactive monitoring of your mobile computers to prevent downtime. You can easily see the health of the device and can help pinpoint the source of a problem to determine if it is hardware or software related. Intermec Dashboard displays information such as the status of network connections, battery usage, storage space, and internal devices.
Chapter 8 — Troubleshoot and Maintain the Computer Troubleshoot Your Mobile Computer Use the troubleshooting tables in this section to fix problems with the Wi-Fi connection, 802.1x security, the imager, or general problems with operating the mobile computer. If you send the computer in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution A network connection icon appears in the The computer may not be communicating with the toolbar, but then disappears. intended access point. Make sure the network name matches the access point network name. Default network name is “INTERMEC.” The access point may not be communicating with the server. Ensure the access point is turned on, properly configured, and has 802.1x security enabled. Troubleshoot 802.
Chapter 8 — Troubleshoot and Maintain the Computer Check 802.11 Network Status If you have trouble connecting to your 802.11 wireless network: • Make sure you have correctly set network parameters on the computer. • Check your wireless security settings. Follow the next procedure to verify available access points and networks, check signal strength, and view other diagnostics.
Chapter 8 — Troubleshoot and Maintain the Computer c Tap Ping. The graph shows the amount of time it takes for the host to return the ping. Tap List to see this information in a list format. 5 Tap the RSSI tab to view the received signal strength of the host signal. The information box includes the current signal strength, host SSID name, MAC address, data rate, and transmit power. • Tap Mark to place an arrow marker above the graph. 6 Tap the Conf tab to set up a log file that lists RSSI history.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution When you release a Scan button The Good Read light will remain on if you configure the or handle trigger, the Good Read computer to use continuous/edge triggering. If you configure light does not turn off. the computer for level triggering and the Good Read light remains on, there may be a problem. Press one of the Scan buttons or pull the trigger again without scanning a bar code label.
Chapter 8 — Troubleshoot and Maintain the Computer Use ScanDiagnostic to Troubleshoot the Scanner Use the ScanDiagnostic application to troubleshoot problems such as the inability to read a bar code or a scanner that does not turn on. 1 From the Home menu, tap Start > ScanDiagnostic. 2 From the Scan Health screen, select the scanner you want to troubleshoot and then tap Diagnose. The application checks to make sure the scanner is enabled and checks settings to make sure they are optimized.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution The computer appears to be locked up and you cannot enter data. • Press the Power button and select Suspend from the Power Options menu. Press the Power button to turn the screen back on. • Press the Power button and select Reboot from the Power Options menu. • Remove the battery and press the Reset button to perform a cold boot. For help, see “Cold Boot the Computer” on page 123. • Try reloading the firmware.
Chapter 8 — Troubleshoot and Maintain the Computer Call Product Support If you cannot find the answer to your problem in the “Troubleshooting the Computer” section, you can visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support.
Chapter 8 — Troubleshoot and Maintain the Computer Find Your Operating System Version Use the following procedure to find the OS version of your mobile computer. 1 Press the Intermec Dashboard (m) button to launch the Dashboard. 2 Tap the Information bar. The Information Details page appears and displays information such as the firmware version and the OS version.
Chapter 8 — Troubleshoot and Maintain the Computer Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All other data, such as configuration and network settings, is preserved. 1 Press the Power button to suspend the computer. 2 Remove the handstrap and the battery pack. 3 Press the Reset button in the battery compartment on the back of the computer.
Chapter 8 — Troubleshoot and Maintain the Computer Clean Boot the Computer A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of those found in the Flash File Store, or any removable storage. If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and running for further troubleshooting. You can perform a clean boot using the mobile computer.
Chapter 8 — Troubleshoot and Maintain the Computer 1 Press the Power button and choose to suspend the computer. 2 Dip a clean cloth towel in the ammonia solution and wring out the excess. 3 Wipe off the imager window, camera lens, and flash area. Do not allow any abrasive material to touch these surfaces. 4 Wipe dry.
A Specifications and Default Settings 127
Appendix A — Specifications and Default Settings Physical and Environmental Specifications CN70 Physical Dimensions Dimensions 16.9 x 8.0 x 3.4 cm (6.66 x 3.14 x 1.35 in) Weight 450 g (15.2 oz) with battery CN70e Physical Dimensions Dimensions 19.5 x 8.0 x 3.4 cm (7.66 x 3.14 x 1.35 in) Weight 491 g (16.6 oz) with battery CK70 Physical Dimensions Dimensions 23.7 x 8.0 x 4.3 cm (9.33 x 3.16 x 1.69 in) Weight 562 g (19 oz) with battery CK71 Physical Dimensions Dimensions 23.7 x 8.0 x 5.0 cm (9.33 x 3.
Appendix A — Specifications and Default Settings Power and Electrical Specifications Battery type Rechargeable Lithium-ion (Li-ion) battery Battery capacity CN70/CN70e: 3.7 V, 4000 mAh (14.8 Wh) CK70/CK71: 3.7 V, 5200 mAh (19.2 Wh) Electrical rating x 4.37/4.8 V; 2/1,5 A 70 Series Non-Incendive Computer Specifications The 70 Series mobile computers with non-incendive (NI) certification comply with the following specifications for North America and Canada regions only.
Appendix A — Specifications and Default Settings Hardware Main processor options TI OMAP3, 1 GHz TI OMAP3, 600 MHz Memory 512 MB RAM Persistent storage 1 GB Flash Removable storage up to 32 GB user-accessible microSD card slot Keypad CN70: QWERTY, Numeric CN70e: QWERTY Numeric, Numeric, Calculator-style CK70: Large Alpha, Alphanumeric CK71: Numeric Function, Alphanumeric Imaging options 5 megapixel color camera and EA30 area imager (all), EV12 (CK71 only), or EX25 (CK71 only) Back Accessory Inter
Appendix A — Specifications and Default Settings Standard Communications • • • • • • • • UMTS (not available on CK71) CDMA (not available on CK71) Flexible Network Radio (not available on CK71) GPS (not available on CK71) 802.11a/b/g/n Bluetooth USB Full Speed V2.0 Host USB Full Speed V2.0 Client Wireless LAN Standards compliant IEEE 802.11a/b/g/n (2.4 GHz and 5 GHz), Single Stream Data rates up to 72Mbps Security 802.11i, WPA, WPA2, 802.
Appendix A — Specifications and Default Settings Bar Code Symbologies The imagers support all of the bar code symbologies listed in the next table.
Appendix A — Specifications and Default Settings Imager Reading Distances Typical reading distances are done in an office environment using office lights (4 lux). Minimum distances are measured in the dark (0 lux). Both reading distances are provided in respective scan engine integration guides. Contact your local Intermec representative for more information. Below are the typical and minimum standard reading distances for the 70 Series computer built with an EA30 imager.
Appendix A — Specifications and Default Settings EA30 Typical Reading Distances - Extended Reading Range These typical reading distances are measured in an office environment (250 lux) for the EA30 standard model with Extended Reading Range activated. Extended Reading Range is enabled by default. EA30 Typical Reading Distances - Extended Reading Range Activated 0" 4" 8" 12" 16" 20" 24" 28" 32" 36" 40" in 12" 30 8" 20 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.
Appendix A — Specifications and Default Settings EA30 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" 20" 24" 28" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 EA30 Minimum Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.1 mm (4 mils) 0.1250 mm (5 mils) 0.
Appendix A — Specifications and Default Settings EA30 Area Imager Typical Reading Distances Typical distances are measured in an office environment (250 lux). 0" 4" 8" 12" 16" 20" 24" 28" 32" 36" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 80 90 EA30 Typical Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.
Appendix A — Specifications and Default Settings EV12 Linear Imager Minimum Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Minimum reading distances are measured in the dark (0 lux). 0" in 2" 4" 8" 6" 10" 12" 14" 16" 8" 20 7" 6" 15 EAN/UPC 100% 5" 4" 10 3" 5 2" 1" 0 0" 1" 5 2" 3" 0.125 mm / 5 mils 10 4" 0.25 mm / 10 mils 5" 6" 15 0.
Appendix A — Specifications and Default Settings EV12 LInear Imager Typical Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Typical reading distances are measured in an office environment (200 lux). 0" in 4" 8" 12" 16" 20" 24" 28" 32" 36" 16" 40 14" 12" 30 10" EAN/UPC 100% 8" 20 6" 10 4" 2" 0 0" 2" 10 4" 6" 0.125 mm / 5 mils 20 8" 0.25 mm / 10 mils 10" 12" 30 0.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Minimum Reading Distance Minimum reading distances are measured in the dark (0 lux). The following graphic does not include the 0.24 cm (0.09 in) setback for the CK71. 0” 16” 32” 48” 64” 80” 96” 128” 112” 144” 160” 176” in 80” 200 64” 160 100% EAN contrast UPC 48” 120 32” 80 16” 40 0” 0 16” 40 32” 80 0.25 mm/10 mils 48” 120 0.5 mm/20 mils 1 mm/40 mils 64” 160 1.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Typical Reading Distance Typical reading distances are measured in an office environment (200 lux). The following graphics do not include the 0.24 cm (0.09 in) setback for the CK71. EX25 Near-Far Range Imager 1D Typical Reading Distances in 0” 40” 80” 120” 160” 200” 240” 280” 320” 360” 400” 440” 480” 160” 400 128” 320 100% EAN contrast UPC 96” 240 64” 160 32” 80 0” 0 32” 80 0.25 mm 10 mils 160 64” 0.
Appendix A — Specifications and Default Settings EX25 1D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance Code 39 0.25 mm (10 mils) 0.5 mm (20 mils) 1 mm (40 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 15 cm (5.91 in) 16 cm (6.30 in) 25 cm (9.84 in) 40 cm (15.75 in) ** 135 cm (53.15 in) 280 cm (110.24 in) 550 cm (216.54 in) 720 cm (283.46 in) 1200 cm (472.44 in) Code 128 retro-reflective 2.5 mm (100 mils) ** 1300 cm (511.
Appendix A — Specifications and Default Settings EX25 2D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance DataMatrix 0.25 mm (10 mils) 0.76 mm (30 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 7.5 mm (300 mils) 15 cm (5.91 in) 25 cm (9.84 in) ** ** 20 cm (7.87 in) 90 cm (35.43 in) 310 cm (122.05 in) 450 cm (177.17 in) 1100 cm (433.07 in) 1524 cm (600 in) ** Minimum distance depends on bar code width and scan angle.
Appendix A — Specifications and Default Settings Symbology Settings Symbology Default Value AustraliaPost Disable Aztec Disable BPO Disable CanadaPost Disable Codabar Disable Codablock A Disable Codablock F Disable Code 11 Disable Code 39 Enable Code 93 Disable Code 128/GS1-128 Enable DataMatrix Enable DutchPost Disable EAN/UPC Enable UPC A, UPC E, EAN 8, EAN 13 GS1 Composite Disable GS1 DataBar Expanded Disable GS1 DataBar Limited Disable GS1 DataBar Omni-Directional D
Appendix A — Specifications and Default Settings Symbology Default Value Standard 2 of 5 Disable SwedenPost Disable Telepen Disable TLC 39 Disable Symbology Option Settings Symbology Option Settings Default Value Preamble None (Disabled) Postamble None (Disabled) Symbology Identifier Disable Multicode Disable Scanner Settings Scanner Settings Default Value Trigger Predefined Modes Level Trigger Mode Level Aimer Mode Typical aimer Hardware Trigger Enable Trigger Timeout (sec) 2
Appendix A — Specifications and Default Settings Imager Settings Default Value Image Capture Output Compression Output Compression Quality Edge Enhancement Noise Reduction Subsampling Image Rotation Image Lighting Correction Bitmap 0 None 0 None None Disable Decode Security Settings Decode Security Settings Default Value Consecutive Data Validation 0 Identical Consecutive Timeout 300 ms Different Consecutive Timeout 0 Center Decoding Disable Center Decoding Tolerance 0 Communications Use com
Appendix A — Specifications and Default Settings 802.11 Radio Setting Default Value Import User Certificates False Import Pac Files False Radio Bands b/g (2.
Appendix A — Specifications and Default Settings Good Read Settings Good Read Setting Default Value Internal Scanner Good Read Beep Tethered Scanner Bluetooth Scanner Good Read Beep One Beep One Beep One Beep Backlight Settings Backlight Setting Default Value Display Backlight Adjustment Keypad Backlight Light Level Normal On Based on Light Level Low Screen Settings Screen Setting Default Value Screen Rotations Screen Rotation Sensor Portrait 0 Degrees Disabled Sound Settings Sound Setting Def
Appendix A — Specifications and Default Settings Power Management Settings Power Management Setting Default Value Enable Power Button Screen Screen Options Displayed On Hibernate, Suspend, Reboot Screen Timeout (Seconds) 5 Power Button Behavior Suspend Device Turns Off After (Battery Power) 5 minutes Screen Turns Off After (Battery Power) Disabled Device Turns Off After (External Power) Disabled Screen Turns Off After (External Power) Disabled Device Off Sensor Disabled Profiles Settings Application Pr
Appendix A — Specifications and Default Settings GPS Settings Use GPS settings to configure how the mobile computer communicates with the GPS network. GPS GPS Setting Default Value Enable Bread Crumbing Disable Core Messaging Service Settings Use core messaging service settings to configure the message routers between client and server software applications.
Appendix A — Specifications and Default Settings Device Health Screen Captures Device Health Screen Captures Setting Default Value Directory \SmartSystems\ScreenCapture Screen Captures Allowed 3 Device Wipe Device Wipe Setting Default Value Enable Wipe Disabled Interval (in days) Null Virtual Wedge Settings Use virtual wedge settings to configure the virtual wedge.
B Keypads and Keystrokes 151
Appendix B — Keypads and Keystrokes Standard Characters Use the following tables to learn how to enter standard and other available characters and functions with the keypad. If there is no sequence of keystrokes for a particular character or function, it is only available through the soft input panel (SIP), which you can access by tapping the keyboard icon on the touch screen. Note: You can only enter “*” and “#” characters in the phone or contacts applications.
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad n c66 c666 c7 c77 c777 c7777 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 N O P Q R S T U V W X Y Z yA yB yC yD yE yF yG yH o p q r s t u v w x y z A B C D E F G H 70 Series Mobile Computer User Manual 153
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad I c1444 c15 c155 c1555 c16 c166 c1666 c17 c177 c1777 c17777 c18 c188 c1888 c19 c199 c1999 c19999 0 1 2 yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV yW yX yY yZ b, bY bU J K L M N O P Q R S T U V W X Y Z 0 1 2 154 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad 3 3 4 5 6 7 8 9 bI bH bJ bK bB bN bM 4 5 6 7 8 9 CN70 Characters and Functions To Enter Numeric Keypad QWERTY Keypad @ (at symbol) N/A & (ampersand) N/A * (asterisk) * : (colon) N/A , (comma) N/A $ (dollar) N/A ! (exclamation) N/A - (hyphen) - % (percent) N/A . (period) . b# bQ bS bC bD bX bE bO bG bR .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad QWERTY Keypad ? (question mark) N/A ‘ (apostrophe) N/A Forward Tab j { u d l r c1 e b| b or c c0 b m or c m | p w m bA bZ j { u d l r yy e bP b or y s bm | p w m Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard 156 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CN70e Keypads and Keystrokes CN70e Alphanumeric Characters Character Numeric Keypad a b c d e f g h i j k l m n o p q r s c2 c22 c222 c3 c33 c333 c4 c44 c444 c5 c55 c555 c6 c66 c666 c7 c77 c777 c7777 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c8 c88 c888 c9 c99 c999 c4 c44 c444 c5 c55 c555 c6 c66 c666 c1 c11 c111 c1111 A B C D E F G H I J K L M N O P Q R S 157
Appendix B — Keypads and Keystrokes Character Numeric Keypad t u v w x y z A B C D E F G H I J K L M N 158 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 c1444 c15 c155 c1555 c16 c166 Calculator-Style Keypad QWERTY Numeric Keypad c2 c22 c222 c3 c33 c333 c3333 c78 c788 c7888 c79 c799 c7999 c74 c744 c7444 c75 c755 c7555 c76 c766 T U V W X Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 c1666 c17 c177 c1777 c1777 7 c18 c188 c1888 c19 c199 c1999 c1999 9 0 1 2 3 4 5 6 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c7666 c71 c711 c7111 c7111 1 c72 c722 c7222 c73 c733 c7333 c7333 3 0 1 2 3 4 5 6 yO yP yQ yR yS yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 159
Appendix B — Keypads and Keystrokes Character Numeric Keypad 7 8 9 7 8 9 Calculator-Style Keypad QWERTY Numeric Keypad 7 8 9 7 8 9 CN70e Characters and Functions To Enter Numeric Keypad Calculator-Style Keypad @ (at symbol) N/A N/A & (ampersand) N/A N/A * (asterisk) * * : (colon) N/A N/A , (comma) N/A N/A $ (dollar) N/A N/A ! (exclamation) N/A N/A - (hyphen) - - % (percent) N/A N/A . (period) . b# .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad Calculator-Style Keypad QWERTY Numeric Keypad Up Arrow u d l r c1 e b| b or c c0 b m or c m | p w m u d l r c7 e b| b or c c0 b m or c m | p w m u d l r yy e b| b or y s bm | p w m Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard CK70 Keypads and Keystrokes CK70 Alphanumeric Characters Character Large Alpha Keypad Alphanumeric Keypad a A B C A B C b c 70 Series Mob
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad d D E F G H I J K L M N O P Q R S T U V W X D E F G H I J K L M N O P Q R S T U V W X e f g h i j k l m n o p q r s t u v w x 162 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad y Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS z A B C D E F G H I J K L M N O P Q R S 70 Series Mobile Computer User Manual 163
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad T yT yU yV yW yX yY yZ bP bD bE bF bG bH bI bK bL bM yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 U V W X Y Z 0 1 2 3 4 5 6 7 8 9 CK70 Characters and Functions To Enter Large Alpha Keypad Alphanumeric Keypad @ (at symbol) bS bW N/A & (ampersand) 164 bU 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad * (asterisk) bO bJ cJ bT cS cW cX cO . bX bQ cQ cT bY cY cN bN bV cV b0 b2 b5 cX : (colon) ; (semicolon) , (comma) $ (dollar) ! (exclamation) - (hyphen or minus) % (percent) .
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad ~ (tilde) N/A \ (backslash) cU bU bW c8 b8 bZ / (forward slash) “ (quotes) N/A ( (left parenthesis) bR cR bZ cZ bs ) (right parenthesis) Insert Delete Sym ¦ (broken vertical bar) ̀ (grave) Forward Tab Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift 166 N/A N/A j { u d l r yy e cm y N/A N/A b4 b6 N/A cS cW j { u d l r yy e cm y 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad Space s b m or c m | s b m or c m | Alt N/A Alt Ctrl Ctrl Ctrl Send Call bA bC m c1 c3 m To Enter Large Alpha Keypad Alphanumeric Keypad F1 cD cE cF cG cH cI cK cL cM cP ¡ ¢ £ ¤ ¥ b¡ b¢ b£ b¤ b¥ bA bB Start (Windows) Esc End Call Intermec Dashboard CK70 Function Keys F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 N/A N/A 70 Series Mobile Computer User Manual 167
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad F13 Alphanumeric Keypad bC bD bE bF bG bH bI bJ bK bL bM bN N/A F14 N/A F15 N/A F16 N/A F17 N/A F18 N/A F19 N/A F20 N/A F21 N/A F22 N/A F23 N/A F24 N/A CK71 Keypads and Keystrokes CK71 Alphanumeric Characters Character Numeric With Function Keys Keypad Alphanumeric Keypad a b7 b8 b9 b4 b5 b6 A B C D E F b c d e f 168 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad g b1 b2 b3 b0 bb¡ b¢ b£ b¤ b¥ b¦ b§ b¨ b© bª b« b¬ bm b Ctrl b Alt by7 G H I J K L M N O P Q R S T U V W X Y Z yA h i j k l m n o p q r s t u v w x y z A 70 Series Mobile Computer User Manual 169
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad B by8 by9 by4 by5 by6 by1 by2 by3 by0 byby¡ by¢ by£ by¤ by¥ by¦ by§ by¨ by© byª by« yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV C D E F G H I J K L M N O P Q R S T U V 170 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad W by¬ bym b y Ctrl b y Alt 0 1 2 3 4 5 6 7 8 9 yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 X Y Z 0 1 2 3 4 5 6 7 8 9 CK71 Characters and Functions To Enter Numeric With Function Keys Keypad Alphanumeric Keypad : (colon) cs ; (semicolon) N/A b8 b5 cX , (comma) $ (dollar) ! (exclamation) N/A cS cW 70 Series Mobile Computer User Manual N/A N/A 171
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad - (hyphen or minus) . cs . bs bY bS cX cV bV bT cT bU cU bW c2 b2 bZ b4 b6 cS cW j .
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Backspace { u d l r yy e cm y s b m or c m | { u d l r yy e cm y s b m or c m | b| Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Alt Alt Ctrl Ctrl Ctrl Intermec Dashboard m m To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F1 ¡ ¢ £ ¤ ¡ ¢ £ ¤ CK71 Function Keys F2 F3 F4 70 Series Mobile Computer User Manual 173
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F5 ¥ ¦ § ¨ © ª « ¬ c¡ c¢ c£ c¤ c¥ c¦ c§ c¨ c© cª c« c¬ ¥ b¡ b¢ b£ b¤ b¥ bA bB bC bD bE bF bG bH bI bJ bK bL bM bN F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 174 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CK71 Intermec Terminal Emulation (ITE) Keys To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Attention c0 Autolog N/A Clear b6 Duplicate N/A EEOF N/A Erase N/A cA c¤ c6 cD c¥ cE cF c1 c1 cG b3 cI cH cK cM cO cN b9 c¡ c¢ Find Field + Field Fieldmark Help Hex Home Keypad Menu Mode New Line Next Screen PA1 PA2 N/A cx bx N/A N/A N/A c.
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad PA3 c3 cd c£ cd cP c7 cR c| ce c5 c8 cQ bd Page Print N/A Previous Screen c7 Remove N/A Reset c| ce c5 c8 br Return Roll Down Roll Up System Request View View Down View Up 176 N/A bd bu N/A N/A 70 Series Mobile Computer User Manual
C ScanNGo Wi-Fi Configuration Bar Codes You can use the ScanNGo Wi-Fi configuration bar codes to quickly configure the 802.11 radio in your computer.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes Radio Configuration Bar Codes Use the following ScanNGo bar codes to enable the 802.11 radio and set the defaults for either Funk or Microsoft Wireless Zero Configuration security. After you scan the bar codes, you will still need to use Intermec Settings or another configuration program to set network-specific settings on your computer and to configure the wireless security. The CN70, CN70e, and CK70 are available with the EA30 imager only.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 2D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 1D Configuration Bar Codes You can configure the computer with a 1D imager (EV12). 1 Scan the START HERE bar code from the table and wait for the program to start. 2 Scan the 1/9 bar code. 3 Scan the rest of the bar codes in any order.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 1D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 180 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 70 Series Mobile Computer User Manual 181
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 182 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 70 Series Mobile Computer User Manual 183
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 184 70 Series Mobile Computer User Manual
I Index 185
Index Symbols .cab files, using to install applications 108 Numerics 70 Series computer models 2 features 5 802.11 communications, configuring 83 802.11 network status, troubleshooting 117 802.11 radio, default settings 145 802.
Index CDMA phone activating 54 carriers 54 certificate, loading 102 changing the battery 11 characters entering on CK70/CK71 keypad 24 entering on numeric keypad 23 entering on QWERTY keypad 23 entering with keystrokes 152– 176 charging accessories 11 charging the battery 11 CK70 keypads, illustrated 19, 20 keystrokes, listed 161–168 status LEDs 6, 7 CK70/CK71 battery, described 8 entering characters on keypad 24 magstripe reader adapter, described 8 CK71 keypads, illustrated 21, 22 keystrokes, listed 168–1
Index files, transferring to and from PC 36 fix interval, configuring with iGPS 72 flash file store, using computer as 37 flashlight, using 28 flick, screen gesture, described 41 Funk security configuring 802.1x 95 configuring LEAP 96 configuring static WEP 96 configuring WPA Enterprise (802.1x) 93 configuring WPA Personal (PSK) 94 configuring WPA2 Enterprise (802.
Index keypad (continued) keystrokes for entering characters 152–176 troubleshooting keys 121 Knowledge Central website 122 L language provisioning 10 launching applications automatically 110 LEAP, configuring with Funk 96 LEDs battery status, described 14 status, described 7 location, status LEDs 7 locked computer, troubleshooting 121 M magstripe reader adapter, described 8 magstripe reader snap-on adapter, described 8 mass storage device, using computer as 37 memory, computer 130 microSD card about 30 inst
Index product support calling 122 Profile Settings application, described 46 configuring with Intermec Settings 80 profile, choosing Funk security 93 Q QWERTY keypad CN70, illustrated 16 entering characters on 23 illustrated 16 QWERTY numeric keypad CN70e, illustrated 17 R reading distances EA30 area imager 135 EV12 linear imager 137 EX25 imager 139 Ready-to-Work LED described 7 reboot performing 123 power option described 26 recording a video 66 regulatory approvals 131 reset button, location 124 performin
Index Suspend, power option described 26 symbologies, supported 132 system software updating with microSD card 112 updating with SmartSystems Foundation 111 T terminal emulation, troubleshooting 115 tethered scanner, connecting 89 tethered stylus replacement kit, described 9 Tile bar described 40 illustration 40 Title bar described 40 illustration 40 status icon descriptions 42 transferring files, to and from PC 36 troubleshooting 115–119 802.11 network status 117 802.
Index www.intermec.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2012 Intermec Technologies Corporation. All rights reserved.
