ASSEMBLY INSTRUCTIONS PLEASE READ! IN ORDER TO COMPLY WITH MANDATED ANTI TIPPING SAFETY REGULATIONS, THIS UNIT HAS A LOCKING MECHANISM THAT ALLOWS TO OPEN ONLY ONE DRAWER AT A TIME. WARNING! Serious or fatal injuries can occur from furniture tip over. Use tip over restraint (provided) to secure this product to the wall. Description Item No. : BROOKLYN 3 DRAWER CHEST : BD-8003 ITEM NO.
BEFORE ASSEMBLY Thank you for purchasing this quality product. This product has been designed for easy assembly and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is missing or defective, please contact the store where purchased. If hardware is missing, or you need help with assembly, please call toll free 888-944-8396.
PART LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have the following parts: NO Description Qty A Top C Sketch NO Description Qty 1 B Bottom Frame 1 Side Panel (Left) 1 D Side Panel (Right) 1 E Back Rail 1 F Back Panel 2 G Anti-tip Board 1 H Drawer Side 3 I Drawer Side 3 J Drawer Front 3 K Drawer Back 3 L Drawer Bottom 3 M Support Bar 3 ITEM NO.
HARDWARE LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have all of the following hardware: NO Description Qty 1 Short Bolt (M6 x 30mm) 2 Sketch NO Description Qty 6 8 Pan head screw (M4 x 25mm) 6 Long Bolt (M6 x 60mm) 2 9 Wooden Knob (30 x 30mm) 6 3 U-washer (M6) 2 10 Short Screw (M4 x 30mm) 6 4 Spring Washer (6.5 x 11mm) 6 11 Short Pan head screw (M4 x 15mm) 2 5 Flat Washer (6.
NOTE: WARNING LABEL (INCLUDED) STEP 1 Attach side panel (C) to top (A) with bolts (1) and washers (4) and (5) as shown below. Tighten with Allen key (6). ITEM NO.
STEP 2 Attach bottom frame (B) to side panel (C) with bolt (2) and u-washer (3), bolts (1) and washers (4) and (5) as shown below. Tighten with Allen key (6). Insert back rail (E) and anti-tip board (G) into side panel (C). Slide back panels (F) into the grooves as shown below. STEP 3 Attach side panel (D) to top (A) and bottom frame (B) with bolt (2) and u-washer (3), bolts (1) and washers (4) and (5) as shown below. Tighten with Allen key (6).
STEP 4 Attach drawer sides (H) and (I) to drawer front (J) with screws (7) as shown below. Tighten with a screwdriver. Insert drawer bottom (L) into the grooves at bottom of drawer sides (H), (I) and front drawer (J) as shown below. STEP 5 Attach drawer back (K) to drawer sides (H) and (I) with screws (7) as shown below. Tighten with a screwdriver. Attach support bars (M) to bottom of drawers with screws (10) as shown below. Tighten with a screwdriver. ITEM NO.
STEP 6 Attach knobs (9) to front of drawers with pan head screws (8) as shown below. Tighten with a screwdriver. ITEM NO.
STEP 7 Move the arm of the Anti-tip Snapper to the forward locked position, then install the 1st drawer as shown below. STEP 8 Move the arm of the Anti-tip Snapper to the forward locked position, then install the 2nd drawer as shown below. ITEM NO.
STEP 9 Move the arm of the Anti-tip Snapper to the forward locked position, then install the 3rd drawer as shown below. ITEM NO.
STEP 10 Attach brackets (13) to the back of the unit with screws (11) through the smaller holes in the brackets as shown below. Important! Properly attach the other brackets (13) to the wall in an area of drywall or plaster with a wood stud: Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood stud(s) in the wall. Place the unit into position so both mounting brackets are vertically in line.
