ASSEMBLY INSTRUCTIONS WARNING! Serious or fatal injuries can occur from furniture tip over. Use tip over restraint (steel band included) to secure this product to the wall. Description Item No. : BROOKLYN 3 DRAWER NIGHTSTAND : BD-8013 Printed in Vietnam ITEM NO.
BEFORE ASSEMBLY Thank you for purchasing this quality product. This product has been designed for easy assembly and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is missing or defective, please contact the store where purchased. If hardware is missing, or you need help with assembly, please call toll free 888-944-8396.
PART LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have the following parts: NO Description Qty A Top C Bottom panel E Upper Drawer front G Upper Drawer back I Lower Drawer side (L-R) 4 K Drawer bottom 3 Sketch NO Description Qty 1 B Side panel (L-R) 2 1 D Back panel 1 F Upper Drawer side (L-R) H Lower Drawer front J Lower Drawer back 1 1 Sketch 2 2 2 Printed in Vietnam ITEM NO.
HARDWARE LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have all of the following hardware: NO Description Qty 1 Bolt (M6 x 30mm) 3 Sketch NO Description Qty 8 2 Spring washer (6.5 x11mm) 8 Flat washer (6.5 x13mm) 8 4 Long screw (M4 x 35mm) 26 5 Wooden knob (30 x 30mm) 3 6 Pan head screw (M4 x 30mm) 3 7 Allen key (M4 x 30mm x 110mm) 1 8 Steel band 2 9 Short screw (M3.
STEP 1 Attach top (A) and bottom panel (C) to side panel (B) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (7). Slide back panel (D) into the grooves as shown below. STEP 2 Attach bottom panel (C) and top (A) to the other side panel (B) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (7). Printed in Vietnam ITEM NO.
STEP 3 Attach drawer sides (F) to drawer front (E) with screws (4) as shown below. Tighten with a screwdriver. Insert drawer bottom (K) into the grooves at bottom of drawer sides (F) and drawer front (E) as shown below. STEP 4 Attach drawer back (G) to drawer sides (F) with screws (4) as shown below. Tighten with a screwdriver. STEP 5 Attach knob (5) to front of drawer with pan head screw (6) as shown below. Tighten with a screwdriver. Carefully put the drawer into the unit. Printed in Vietnam ITEM NO.
STEP 6 Attach drawer sides (I) to drawer front (H) with screws (4) as shown below. Tighten with a screwdriver. Insert drawer bottom (K) into the grooves at bottom of drawer sides (I) and drawer front (H) as shown below. STEP 7 Attach drawer back (J) to drawer sides (I) with screws (4) as shown below. Tighten with a screwdriver. STEP 8 Attach knobs (5) to front of drawers with pan head screws (6) as shown below. Tighten with a screwdriver. Carefully put the drawers into the unit.
STEP 9 Attach steel bands (8) to the unit with screws (9) as shown below. (to secure the product to the wall and reduce the risk of tipping over). Important! Properly attach steel bands (8) to the wall in an area of drywall or plaster with a wood stud: Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood stud(s) in the wall. Drill 1/8-inch (3mm) diameter hole(s) into the wood stud(s) located in the wall, where you marked with the pencil.