ASSEMBLY INSTRUCTIONS WARNING! Serious or fatal injuries can occur from furniture tip over. Use tip over restraint (steel band included) to secure this product to the wall. Description Item No. : BROKLYN 6 DRAWER DRESSER : BD-8006 Printed in Vietnam ITEM NO.
BEFORE ASSEMBLY Thank you for purchasing this quality product. This product has been designed for easy assembly and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is missing or defective, please contact the store where purchased. If hardware is missing, or you need help with assembly, please call toll free 888-944-8396.
PART LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have the following parts: NO Description Qty A Top C Sketch NO Description Qty 1 B Bottom panel 1 Vertical panel 1 D Side panel (L-R) 2 E Back rail 1 F Back panel 2 G Support leg 1 H Drawer side (L-R) 12 I Drawer front 6 J Drawer back 6 K Drawer bottom 6 M Support bar 6 Sketch Printed in Vietnam ITEM NO.
HARDWARE LIST When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please make sure you have all of the following hardware: NO Description Qty 1 Bolt (M6 x 30mm) 2 Sketch NO Description Qty 14 6 Pan head screw (M4 x 30mm) 12 Spring washer (6.5 x 11mm) 14 7 Wooden knob (30 x 30mm) 12 3 Flat washer (6.
STEP 1 Attach the top (A) and bottom panel (B) to vertical panel (C) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (4). STEP 2 Attach the top (A) and bottom panel (B) to side panel (D) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (4). Slide back panels (F) and back rail (E) into the grooves as shown below. Printed in Vietnam ITEM NO.
STEP 3 Attach the top (A) and bottom panel (B) to the other side panel (D) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (4). Attach support leg (G) to vertical panel (C) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (4). STEP 4 Attach back rail (E) to the unit with screws (5) as shown below .Tighten with a screwdriver. Printed in Vietnam ITEM NO.
STEP 5 Attach drawer sides (H) to drawer front (I) with screws (5) as shown below. Tighten with a screwdriver. Insert drawer bottom (K) into the grooves at bottom of drawer sides (H) and drawer front (I) as shown below. STEP 6 Attach drawer back (J) to drawer sides (H) with screws (5) as shown below. Tighten with a screwdriver. Printed in Vietnam ITEM NO.
STEP 7 Attach support bars (M) to bottom of drawers with screws (8) as shown below. Tighten with a screwdriver. STEP 8 Attach knobs (7) to front of drawers with pan head screws (6) as shown below. Tighten with a screwdriver. Carefully put the drawers into the unit. Printed in Vietnam ITEM NO.
STEP 9 Attach steel bands (9) to the unit with screws (10) as shown below. (to secure the product to the wall and reduce the risk of tipping over). Important! Properly attach steel bands (9) to the wall in an area of drywall or plaster with a wood stud: Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood stud(s) in the wall. Drill 1/8-inch (3mm) diameter hole(s) into the wood stud(s) located in the wall, where you marked with the pencil.