T E C H N I C A L M A N U A L O C T. 2 0 0 2 www.centiva.com by International Floors of America, Inc.
CENTIVA LUXURY FLOORING CONTENTS Introduction------------------------------------------------------------------------------------------------------------- 2-3 Product Characteristics ----------------------------------------------------------------------------------------------- 4-5 Product Specifications ----------------------------------------------------------------------------------------------- 6-10 Product Installation Guidelines Proper Subfloor Preparation ------------------------------------------
INTRODUCTION Important: To preserve the warranty and deliver the best possible installation to your customer, follow the instructions in this manual. Safety Warning: Centiva vinyl tile contains no asbestos fibers. When removing existing resilient floor coverings, carefully observe the following warning: Existing resilient floor coverings and black asphalt adhesive may contain asbestos. Improper procedures used to remove these products could release asbestos fibers into the air.
PRODUCT CHARACTERISTICS Classic Series* Homogeneous: Multi-layered/Chip Construction: Event Series Multi-layered & Film Photograph: Classic & Event Series Color & Textures: Special Edge Treatments: Centiva manufactures homogeneous products for heavy commercial or residential usage. These tiles are solid vinyl tiles with a standard gauge of 1/8” (3mm). Specially developed products in multi-layered sheet form including a recycled backing and high-density wear layer with a standard gauge of a minimum .
PRODUCT SIZE AND PACKAGING: Classic Series Product Coral Reef Size in Inches 9x9 12 x 12 12 x 18 18 x 18 18 x 36 4 x 36 6 x 36 36 x 36 Magics 9x9 12 x 12 12 x 18 18 x 18 18 x 36 4 x 36 6 x 36 36 x 36 Italian Marble 9x9 12 x 12 12 x 18 18 x 18 18 x 36 4 x 36 6 x 36 36 x 36 Concrete 9x9 12 x 12 12 x 18 18 x 18 18 x 36 4 x 36 6 x 36 36 x 36 New Terrazzo U.S.
CENTIVA PRODUCT SPECIFICATIONS Commercial and Residential: All material shall be Centiva by International Floors of America, Inc. Every style has a 10-character code. The first two characters represent the style, the next four are the color number, the next two are the surface, and the last two are the selected edge XX - XXXX - XX – XX in size XX” x XX” Centiva products shall only be installed with the IFA recommended adhesives.
Magics Construction: Standard Sizes: Gauge: Wearlayer: Packaged: Approximate Weight: Surfaces: Edge Treatments: Standard Colors: Slip Resistance Reference Specifications: Recommended Static Load: Taber Abrasion Test: Fire Performance: Smoke Density: Flame Spread: Pure solid vinyl 9” x 9”, 12” x 12”, 18” x 18”, and 36” x 36” slabs; custom sizes 1/8” Homogeneous throughout 45 s/f per carton (9” x 9”, 12” x 12”, 18” x 18”); 90 s/f per carton of 36” x 36” For larger projects, slabs of 36” x 36” may be put on p
New Terrazzo Construction: Standard Sizes: Gauge: Packaged: Approximate Weight: Surfaces: Edge Treatments: Standard Colors: Slip Resistance Reference Specifications: Recommended Static Load: Taber Abrasion Test: Fire Performance: Smoke Density: Flame Spread: Through layers of encapsulated chips including recycled backing 18” x 18” 1/8” 45 s/f per carton (18” x 18”) 47 lbs per 18” x 18” carton Smooth Square 5 plus custom colors* Dry – Excellent 0.7100 (ASTM C1028); Wet 0.
ULTRASTONE Rialto Construction: Standard Sizes: Gauge: Wearlayer: Packaged: Approximate Weight: Surfaces: Edge Treatments: Standard Colors: Slip Resistance: Critical Radiant Flux: Recommended Static Load: Smoke Generation: Flame Spread: Solid Vinyl Tile 12” x12”, 18” x 18”, and 36” x 36” slabs; custom sizes .120 mil (3mm) Clear Rigid, High-Density PVC of .
Good Ole Woods/Bamboo Construction: Standard Sizes: Gauge: Wearlayer: Packaged: Approximate Weight: Surfaces: Edge Treatments: Standard Colors: Slip Resistance Critical Radiant Flux; Recommended Static Load: Smoke Generation: Flame Spread: Solid Vinyl Tile 4” x 36” and custom .120 mil (3mm) Clear Rigid, High-Density PVC of .30 Mil 45 s/f per carton 47 lbs per carton Tick/Frost/Rustic Slight Bevel 9 and 2 plus custom colors* D-2047-82 Static Coefficient of Friction on wet and dry surfaces ASTM E-648 .
INSTALLATION Commercial & Residential There are three (3) basic requirements necessary to assure a long lasting, attractive Centiva® floor: 1. Proper Subfloor Preparation 2. Installation 3. Adhesives The following guidelines will help to ensure complete satisfaction with your installation by fulfilling these requirements. Centiva tiles and planks are suitable for surfaces on above and below grade. Centiva can be installed over concrete or wood subfloors. 1.0 SUBFLOOR PREPARATION 1.
2.0 INSTALLATION Before any installation takes place, please read the following information carefully: − All Centiva tiles and planks should be present at the jobsite for 48 hours at a temperature between 68-72 degrees F in order to acclimate properly. Avoid installations with temperatures above 80 degrees F and below 60 degrees F. All Centiva tiles and planks are duplications of natural or real products; therefore, shades and pattern variations will occur.
2.3 Laying Out The Job Site Using Centiva Classic And Event Series Tiles or Slabs 2.4 Diagonal Layout For Centiva Classic And Event Series Tiles Or Slabs Carefully determining where to begin your tile installation results Extra measurements and guidelines are needed for in the most professional looking job. Always try to end up with diagonal installations. A sketch is useful for any at least half a tile at each wall for best appearance. complicated installation.
2.5 Layout Of Room Using Centiva Event Series Ultraplank, Plankwood, Good Ole Woods Or Bamboo 2.6 Laying Of The Plank Spread adhesive following the specific recommendations for the adhesive outlined in the Adhesives section of the manual. Place the first piece of plank at the junction of the chalk lines. Continue to lay the plan, making sure each plank is flush against the chalk line and tight against the adjoining plank.
2.7 Useful Installation Tips: 2.8 • Intricate cuts around door frames, cabinets, transitions, etc. It is always recommended to fit in prior to spreading adhesive. See also adhesive pages. • Have several clean white cloths and a container of denatured alcohol or mineral spirits available for cleaning off excess adhesive from the tile as you work. Any excess adhesive must be removed from the tile surface, in between tile seams, or the surrounding area WHILE STILL WET.
3.2 IFA D-2001 Vinyl Plank & Luxury Vinyl Tile Flooring Adhesive Description & Data: Surface Preparation: IFA D-2001 adhesive is solvent-free, non-flammable, freeze/thaw stable, and nearly odor-free. It can be used where other adhesives might present potential health risks. It is suitable for office buildings, hotels, hospitals, schools, restaurants, nursing homes, etc. IFA D-2001 adhesive contain one or more micro-biocides to inhibit the growth of mold and mildew.
3.3 IFA PS-5000 Pressure Sensitive Vinyl Tile and Plank Adhesive Description & Data: Surface Preparation: PS-5000 adhesive is solvent-free, non-flammable, freeze/thaw stable, and nearly odor-free. It can be used where other adhesives might present potential health risks. It is suitable for office buildings, hotels, hospitals, schools, restaurants, nursing homes, etc. PS-5000 adhesive contains one or more micro-biocides to inhibit the growth of mold and mildew.
3.4 IFA EP-2000 Epoxy Adhesive (Solvent Free) Description & Data: Surface Preparation: Parts A & B IFA EP-2000 adhesive is solvent-free, non-flammable, and nearly odor-free. It can be used where other adhesives might present potential health risks. It is suitable for use in office buildings, hotels, hospitals, schools, restaurants, nursing homes, etc. IFA EP-2000 is recommended for the installation of vinyl flooring products on approved sub-floors.
CHEMICAL AND STAIN RESISTANCE This test was conducted in accordance with ASTM F 925, Resistance to Chemicals of Resilient Sheet Flooring. By this test, a specified reagent is applied to the surface of the flooring material and allowed to remain in contact for 60 =/- 1 minute. After the exposure of time, the reagent is cleaned from the surface using warm water and the surface dried.
PRODUCT WARRANTY Including 20-Year Limited Wear Warranty International Floors of America, Inc. warrants that its first line quality flooring material is free from manufacturing defects (workmanship and/or material) and will replace defective floor covering for a period of up to one (1) year from the date of purchase in accordance with the conditions set forth below.
by International Floors of America, Inc. Headquarters & Factory 1701 Mars Hill Road Florence, AL 35630 Ph: 256-767-4990 Fax: 256-760-1763 -21- Tech.man.
