Datasheet

ManualsBrandsIntersil ManualsDriversTransceiver RS-232 5.5V 8mA PDIP

FN4315.10

HIN202E, HIN206E, HIN207E, HIN208E,

HIN211E, HIN213E, HIN232E

+/-15kV, ESD-Protected, +5V Powered,

RS-232 Transmitters/Receivers

The HIN202E - HIN232E family of RS-232

transmitters/receivers interface circuits meet all ElA high-

speed RS-232E and V.28 specifications, and are particularly

suited for those applications where ±12V is not available. A

redesigned transmitter circuit improves data rate and slew

rate, which makes this suitable for ISDN and high speed

modems. The transmitter outputs and receiver inputs are

protected to ±15kV ESD (Electrostatic Discharge). They

require a single +5V power supply and feature onboard

charge pump voltage converters which generate +10V and

-10V supplies from the 5V supply. The family of devices

offers a wide variety of high-speed RS-232

transmitter/receiver combinations to accommodate various

applications (see Selection Table).

The HIN206E, HIN211E and HIN213E feature a low power

shutdown mode to conserve energy in battery powered

applications. In addition, the HIN213E provides two active

receivers in shutdown mode allowing for easy “wakeup”

capability.

The drivers feature true TTL/CMOS input compatibility, slew

rate-limited output, and 300Ω power-off source impedance.

The receivers can handle up to ±30V input, and have a 3kΩ

to 7kΩ input impedance. The receivers also feature

hysteresis to greatly improve noise rejection.

Features

• High Speed ISDN Compatible . . . . . . . . . . . . . 230kbits/s

• ESD Protection for RS-232 I/O Pins to ±15kV (IEC1000)

• Meets All RS-232E and V.28 Specifications

• Requires Only 0.1µF or Greater External Capacitors

• Two Receivers Active in Shutdown Mode (HIN213E)

• Requires Only Single +5V Power Supply

• Onboard Voltage Doubler/Inverter

• Low Power Consumption (Typ) . . . . . . . . . . . . . . . . . 5mA

• Low Power Shutdown Function (Typ) . . . . . . . . . . . . .1µA

• Three-State TTL/CMOS Receiver Outputs

• Multiple Drivers

- ±10V Output Swing for +5V Input

-300Ω Power-Off Source Impedance

- Output Current Limiting

- TTL/CMOS Compatible

• Multiple Receivers

- ±30V Input Voltage Range

-3kΩ to 7kΩ Input Impedance

- 0.5V Hysteresis to Improve Noise Rejection

Applications

• Any System Requiring High-Speed RS-232

Communications Port

- Computer - Portable, Mainframe, Laptop

- Peripheral - Printers and Terminals

- Instrumentation, UPS

- Modems, ISDN Terminal Adaptors

Selection Table

PART

NUMBER

POWER SUPPLY

VOLTAGE

NUMBER OF

RS-232

DRIVERS

NUMBER OF

RS-232

RECEIVERS

NUMBER OF

0.1µF

EXTERNAL

CAPACITORS

LOW POWER

SHUTDOWN/TTL

THREE-STATE

NUMBER OF

RECEIVERS

ACTIVE IN

SHUTDOWN

HIN202E +5V 2 2 4 Capacitors NO/NO 0

HIN206E +5V 4 3 4 Capacitors YES/YES 0

HIN207E +5V 5 3 4 Capacitors NO/NO 0

HIN208E +5V 4 4 4 Capacitors NO/NO 0

HIN211E +5V 4 5 4 Capacitors YES/YES 0

HIN213E +5V 4 5 4 Capacitors YES/YES 2

HIN232E +5V 2 2 4 Capacitors NO/NO 0

Data Sheet August 2002

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143

| Intersil (and design) is a registered trademark of Intersil Americas Inc.

Summary of content (21 pages)

PAGE 1
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E ® Data Sheet August 2002 FN4315.10 +/-15kV, ESD-Protected, +5V Powered, RS-232 Transmitters/Receivers Features The HIN202E - HIN232E family of RS-232 transmitters/receivers interface circuits meet all ElA highspeed RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available.
PAGE 2
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Ordering Information (Continued) Ordering Information PART NO. TEMP. RANGE (oC) PACKAGE PKG. NO. PART NO. TEMP. RANGE (oC) PACKAGE PKG. NO. HIN202ECB 0 to 70 16 Ld SOIC (W) M16.3 HIN208EIP -40 to 85 24 Ld PDIP E24.3 HIN202ECBN 0 to 70 16 Ld SOIC (N) M16.15 HIN211ECA 0 to 70 28 Ld SSOP M28.209 HIN202ECBN-T 0 to 70 Tape and Reel HIN211ECA-T 0 to 70 Tape and Reel HIN202ECP 0 to 70 16 Ld PDIP E16.
PAGE 3
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts HIN202E (PDIP, SOIC) TOP VIEW HIN206E (PDIP, SOIC, SSOP) TOP VIEW T3OUT 1 24 T4OUT 15 GND T1OUT 2 23 R2IN 14 T1OUT T2OUT 3 22 R2OUT R1IN 4 21 SD R1OUT 5 20 EN T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN 16 VCC C1+ 1 V+ 2 C1- 3 C2+ 4 13 R1IN C2- 5 12 R1OUT 6 11 T1IN T2OUT 7 10 T2IN V- 9 R2OUT R2IN 8 C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ +5V 9 +5V 16 1 0.1µF + 3 4 0.
PAGE 4
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN208E (PDIP, SOIC, SSOP) TOP VIEW HIN207E (SOIC, SSOP) TOP VIEW T3OUT 1 T1OUT 2 T2OUT 3 22 R2OUT 21 T5IN 20 T5OUT 5 T2IN 6 19 T4IN T1IN 7 GND VCC 1 24 T3OUT T1OUT 2 23 R3IN R2IN 3 22 R3OUT R2OUT 4 21 T4IN T1IN 5 20 T4OUT R1OUT 6 19 T3IN R1IN 7 18 T2IN GND 8 17 R4OUT VCC 9 16 R4IN 23 R2IN R1IN 4 R1OUT T2OUT 24 T4OUT 18 T3IN 17 R3OUT 8 16 R3IN 9 C1+ 10 15 V14 C2- V+ 11 13 C2+
PAGE 5
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN211E (SOIC, SSOP) TOP VIEW T3OUT 1 T1OUT 2 T2OUT 3 HIN213E (SOIC, SSOP) TOP VIEW 28 T4OUT T3OUT 1 28 T4OUT 27 R3IN T1OUT 2 27 R3IN 26 R3OUT T2OUT 3 26 R3OUT R2IN 4 25 SD R2IN 4 25 SD R2OUT 5 24 EN R2OUT 5 24 EN T2IN 6 T1IN 7 23 R4IN T2IN 6 23 R4IN 22 R4OUT T1IN 7 22 R4OUT R1OUT 8 21 T4IN R1OUT 8 21 T4IN R1IN 9 20 T3IN R1IN 9 20 T3IN 19 R5OUT GND 10 19 R5OUT VCC 11 18 R5IN VCC 11 18 R
PAGE 6
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN232E (PDIP, SOIC, SSOP) TOP VIEW +5V 16 1 C1+ 1 16 VCC V+ 2 15 GND 14 T1OUT C1- 3 C2+ 4 13 R1IN C2- 5 12 R1OUT 6 11 T1IN T2OUT 7 10 T2IN V- 0.1µF 3 4 0.1µF T1IN 9 R2OUT R2IN 8 + T2IN R1OUT + 5 C1+ C1C2+ C2- VCC +5V TO 10V VOLTAGE INVERTER V+ +10V TO -10V VOLTAGE INVERTER + 11 +5V 400kΩ T1 10 +5V 400kΩ T2 0.1µF V- 6 + 0.
PAGE 7
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Absolute Maximum Ratings Thermal Information VCC to Ground. . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) < VCC < 6V V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . (VCC -0.3V) < V+ < 12V V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . -12V < V- < (GND +0.3V) Input Voltages TIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V < VIN < (V+ +0.3V) RIN . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Electrical Specifications Test Conditions: VCC = +5V ±10%, (VCC = +5V ±5% HIN207E); C1-C4 = 0.1µF; TA = Operating Temperature Range (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS TIMING CHARACTERISTICS Output Enable Time, tEN HIN206E, HIN211E, HIN213E - 600 - ns Output Disable Time, tDIS HIN206E, HIN211E, HIN213E - 200 - ns HIN213E SD = 0V, R4, R5 - 4.0 40 µs HIN213E SD = VCC , R1 - R5 - 0.
PAGE 9
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Test Circuits (HIN232E) +4.5V TO +5.5V INPUT 0.1µF C3 0.1µF C1 - 2 V+ + 3 C1- + - 0.1µF + C2 - - + 3kΩ 1 C1+ 1 C1+ VCC 16 2 V+ GND 15 3 C1- T1OUT 14 4 C2+ R1IN 13 RS-232 ±30V INPUT 5 C2- R1OUT 12 TTL/CMOS OUTPUT 6 V- 0.
PAGE 10
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E the output, and a logic 0 results in a voltage between +5V and (V+ -0.6V). Each transmitter input has an internal 400kΩ pullup resistor so any unused input can be left unconnected and its output remains in its low state. The output voltage swing meets the RS-232C specifications of ±5V minimum with the worst case conditions of: all transmitters driving 3kΩ minimum load impedance, VCC = 4.5V, and maximum allowable operating temperature.
PAGE 11
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E 1 C1 + 0.1µF TD INPUTS OUTPUTS TTL/CMOS RTS RD 4 HIN232E 3 T1 11 14 T2 10 CTS TD (2) TRANSMIT DATA 7 RTS (4) REQUEST TO SEND 13 12 R2 9 + C2 0.1µF - 5 R1 RD (3) RECEIVE DATA 8 CTS (5) CLEAR TO SEND 15 VCC 16 - 2 C3 + + C4 6 V- V+ 0.2µF 6 2 +5V - RS-232 INPUTS AND OUTPUTS 0.2µF VCC 16 HIN232E C1 + 0.1µF DTR INPUTS OUTPUTS TTL/CMOS DSRS DCD R1 1 4 3 5 T1 11 14 T2 10 12 9 7 13 R2 R1 15 8 + C2 0.
PAGE 12
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Die Characteristics DIE DIMENSIONS: PASSIVATION: 128 mils x 77 mils Type: Nitride over Silox Nitride Thickness: 8kÅ Silox Thickness: 7kÅ METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ TRANSISTOR COUNT: 185 SUBSTRATE POTENTIAL PROCESS: GND CMOS Metal Gate Metallization Mask Layout HIN232E VPIN 6 C2PIN 5 C2+ PIN 4 C1PIN 3 PIN 2 V+ PIN 1 C1+ T2OUT PIN 7 R2IN PIN 8 T3OUT PIN 9 PIN 17 VCC R2OUT PIN 10 PIN 11 T2IN PIN 12 T1IN 12
PAGE 13
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Dual-In-Line Plastic Packages (PDIP) E16.3 (JEDEC MS-001-BB ISSUE D) N 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AE D BASE PLANE -C- SEATING PLANE A2 A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.
PAGE 14
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) N INDEX AREA 0.25(0.010) M H 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 SYMBOL 3 L SEATING PLANE -A- h x 45o A D -C- µα e A1 B 0.25(0.010) M 0.10(0.004) C A M B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3.
PAGE 15
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SSOP) M16.209 (JEDEC MO-150-AC ISSUE B) N INDEX AREA 16 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M 2 GAUGE PLANE 3 0.25 0.010 SEATING PLANE -A- INCHES E -B- 1 B M A D -C- µα e A1 B 0.25(0.010) M L C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - A1 0.002 - 0.05 - - A2 0.065 0.072 1.65 1.85 - B 0.009 0.014 0.22 0.38 9 C 0.004 0.
PAGE 16
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M16.3 (JEDEC MS-013-AA ISSUE C) N INDEX AREA 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE 0.25(0.010) M H B M INCHES E -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.
PAGE 17
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Shrink Small Outline Plastic Packages (SSOP) M24.209 (JEDEC MO-150-AG ISSUE B) N INDEX AREA 24 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M 2 GAUGE PLANE 3 0.25 0.010 SEATING PLANE -A- INCHES E -B- 1 B M A D -C- µα e A1 B 0.25(0.010) M L C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - 0.05 - - 0.072 1.65 1.85 - A1 0.002 A2 0.065 B S B 0.009 0.014 0.22 0.38 9 0.
PAGE 18
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M24.3 (JEDEC MS-013-AD ISSUE C) N INDEX AREA 24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE 0.25(0.010) M H B M INCHES E -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.020 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.5985 0.
PAGE 19
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Shrink Small Outline Plastic Packages (SSOP) M28.209 (JEDEC MO-150-AH ISSUE B) N INDEX AREA 28 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M 2 GAUGE PLANE 3 0.25 0.010 SEATING PLANE -A- INCHES E -B- 1 B M A D -C- µα e A1 B 0.25(0.010) M L C 0.10(0.004) C A M B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.
PAGE 20
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M28.3 (JEDEC MS-013-AE ISSUE C) N INDEX AREA 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE 0.25(0.010) M H B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3.
PAGE 21
HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E File Number Dual-In-Line Plastic Packages (PDIP) E24.3 (JEDEC MS-001-AF ISSUE D) N 24 LEAD NARROW BODY DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 N/2 INCHES -B- SYMBOL -AE D BASE PLANE -C- SEATING PLANE A2 A L D1 e B1 D1 eA A1 eC B 0.010 (0.25) M C L C A B S C eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2.