BACnet MS/TP USER MANUAL Issue date: 05/2019 r1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Important User Information Disclaimer The information in this document is for informational purposes only. Please inform HMS Industrial Networks of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims any responsibility or liability for any errors that may appear in this document. HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous product development.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Router for the integration of MS/TP devices into BACnet IP enabled monitoring and control systems. ORDER CODE INBACRTR0320000 LEGACY ORDER CODE IBBACRTR0320000 © HMS Industrial Networks S.L.U - All rights reserved This information is subject to change without notice URL https://www.intesis.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng INDEX 1 Description ............................................................................................................................................... 5 Introduction ....................................................................................................................................... 5 Functionality ....................................................................................................................
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 1 Description Introduction This document describes how to route messages between BACnet MS/TP and BACnet IP networks using the Intesis BACnet MS/TP to BACnet IP Router. The aim of this is to make accessible data from devices in a BACnet MS/TP network to a BACnet IP network, and viceversa, in a transparent way. Configuration is carried out using the configuration software IntesisTM MAPS.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Functionality After the start up process, Intesis helps route BACnet communications from a BACnet IP to BACnet MS/TP network, allowing BACnet IP devices to communicate with BACnet MS/TP devices present in another network. It is not necessary to perform any mapping as the data from one side is shown on the other side in a transparent way.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 2 Protocol Implementation Conformance Statement BACnet Protocol Implementation Conformance Statement (PICS) Date: 2019-01-02 Vendor Name: HMS Industrial Networks S.L.U Product Name: INBACRTR0320000 Product Model Number: INBACRTR0320000 Application Software Version: 1.0 Firmware Revision: 1.0.0.0 BACnet Protocol Revision: 14 Product Description: BACnet Router Abstraction BACnet Router Objects.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Device Address Binding: Is static device binding supported? (This is currently necessary for two-way communication with MS/TP slaves and certain other devices.) Yes No Networking Options: Router, Clause 6 - List all routing configurations, e.g., ARCNET-Ethernet, Ethernet-MS/TP, etc.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Network Management BIBBs BIBB Type Active NM-CE-A Network Management - Connection Establishment–A NM-CE-B Network Management - Connection Establishment– B NM-RC-A Network Management - Router Configuration–A NM-RC-B Network Management - Router Configuration–B © HMS Industrial Networks S.L.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5 Objects Supported Object Types The objects supported are shown in the table below.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Objects and properties 5.2.1 INBACRTR0320000 (Device Object Type) Property Identifier Property Datatype Value Object_Identifier BACnetObjectIdentifier Object_Name ASHRAE IBOX (Device, 246000) R R CharacterString "INBACRTR0320000" R R Object_Type BACnetObjectType DEVICE (8) (Device Object Type) R R System_Status BACnetDeviceStatus OPERATIONAL (0) R R Vendor_Name CharacterString "HMS Industrial Networks S.L.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 5.2.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 6 Connections Find below information regarding the Intesis connections available. Power Supply Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply. Respect polarity applied of terminals (+) and (-). Be sure the voltage applied is within the range admitted (check table below). The power supply can be connected to earth but only through the negative terminal, never through the positive terminal.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Powering the device A power supply working with any of the voltage range allowed is needed (check section 8). Once connected the RUN led (Figure above) will turn on. WARNING! In order to avoid earth loops that can damage the gateway and/or any other equipment connected to it, we strongly recommend: • The use of DC power supplies, floating or with the negative terminal connected to earth.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 7 Set-up process and troubleshooting Pre-requisites It is necessary to have a BACnet IP client or MSTP device operative and well connected to the corresponding BACnet port of Intesis. Connectors, connection cables, PC to use the configuration tool and other auxiliary material, if needed, are not supplied by HMS Industrial Networks S.L.U for this standard integration.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 7.2.3 Configuration tab Select the Configuration tab to configure the connection parameters. Two subsets of information are shown in this window: General (Gateway general parameters) and BACnet Router (BACnet interface configuration). Figure 7.2 Intesis MAPS configuration tab 7.2.4 Signals All available objects, Object Instances, are listed in the signals tab.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 7.2.5 Sending the configuration to Intesis When the configuration is finished, follow the next steps. 1.- Click on Save button to save the project to the project folder on your hard disk (more information in Intesis MAPS User Manual). 2.- You will be prompted to generate the configuration file to be sent to the gateway. a.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Figure 7.5 Diagnostic More information about the Diagnostic section can be found in the Configuraion Tool manual. © HMS Industrial Networks S.L.U - All rights reserved This information is subject to change without notice URL https://www.intesis.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng Set-up procedure 1. Install Intesis MAPS on your laptop, use the setup program supplied for this and follow the instructions given by the Installation wizard. 2. Install Intesis in the desired installation site. Installation can be on DIN rail or on a stable not vibrating surface (DIN rail mounted inside a metallic industrial cabinet connected to ground is recommended). 3.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 8 Electrical & Mechanical Features Enclosure Plastic, type PC (UL 94 V-0) Net dimensions (dxwxh): 93x53x58 mm Recommended space for installation (dxwxh): 100x60x70mm Color: Light Grey. RAL 7035 Mounting Wall. DIN rail EN60715 TH35. Terminal Wiring (for power supply and low-voltage signals) Power Per terminal: solid wires or stranded wires (twisted or with ferrule) 1 core: 0.5mm2… 2.5mm2 2 cores: 0.5mm2… 1.
IntesisTM BACnet IP Server – BACnet MS/TP User Manual r1.3 eng 9 Dimensions 58 mm (h) 53 mm (w) 93 mm (d) Recommended available space for its installation into a cabinet (wall or DIN rail mounting), with space enough for external connections 70 mm (h) 60 mm (w) 100 mm (d) © HMS Industrial Networks S.L.U - All rights reserved URL This information is subject to change without notice https://www.intesis.
