User Manual

(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/21/2013
109
SAVE THESE INSTRUCTIONS
English
Page 13
TROUBLESHOOTING GUIDE
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service Department
for assistance. See separate “Authorized Service Centers” sheet.
• Filter cord must be plugged into a 3 wire
outlet that is protected by a Class A
Ground Fault Circuit Interrupter.
• Reset circuit breaker. If circuit breaker trips
repeatedly, your electrical system may
have a defect. Turn off circuit breaker and
call an electrician to correct the problem.
• Let motor cool down.
• Adjust the chlorine and pH level. Consult your local
swimming pool supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace if damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Clear any obstructions in the intake hose by
discharging it inside pool wall.
• Tighten hose nuts, check hoses for damage, check
pool water level.
• Clean cartridge more often.
• Clean inside the plunger valve.
• Pull valve handle to full upright position.
• Install the nozzle at the upper position of pool inlet,
and the strainer at the lower position of pool outlet.
• Turn off pump, clear any debris or obstruction in the
outlet, remove all air from the filter pump and turn
pump on again.
• Turn off pump, if water leaking from the vacuum
release valve, then release valve needs to be
replaced. Contact Intex Service Center immediately
to order replacement. You may cover release valve
with the cap temporarily if you ensure that the strainer
cover / strainer grid is installed and you Do Not run
the pump while pool is occupied.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for damage.
• Clear any sticks or leaves in the intake hose.
• Turn and pull valve handle to full upright position.
• Remove cover & check for O-ring.
• Tighten cover or valve (Manually).
• Tighten or reinstall hose nut.
• Put the o-ring back into the groove.
• Replacea new hose.
• Open air release valve, wait until water starts to flow
out of the valves, then close it.
• The lower position of pool outlet connects to filter
pump water inlet. The upper position of pool inlet
connects to filter pump water outlet.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
THE WATER FLOW IS
VERY SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
• The motor is not plugged in.
• The GFCI circuit breaker
is tripped.
• Motor too hot and overload
protection shut motor off.
• Improper chlorine or pH levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is restricting
the water flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• The nozzle and strainer
connection are reversed.
• The vacuum release valve
on the plunger valve is
activated.
• The vacuum release valve
on the plunger valve is
leaking.
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• Faulty motor or the impeller is jammed.
• An air lock inside the cartridge chamber.
• O-ring missing.
• Cover or air release valve are not tight.
• Hose nuts are not well-fitted.
• Hose o-ring dislodged when
connecting the hose.
• Hose broken.
• There’s air trapped in the
pump housing and inlet hose.
• The inlet and outlet hoses
connection are reversed.
TROUBLE CAUSE SOLUTION