(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A ® INTEX OWNER’S MANUAL INFLATABLE BOAT IMPORTANT THIS BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. READ IT THOROUGHLY BEFORE USING THIS PRODUCT AND KEEP IT FOR FUTURE REFERENCE. ISO-6185 BOAT DESIGN CATEGORY D Due to a policy of continuous product improvement, Intex reserves the right to change specifications and appearance, which may result in updates to the instruction manual without notice.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A TABLE OF CONTENTS INTRODUCTION.............................................................................................................................3 MANUFACTURE’S CERTIFICATION..............................................................................................3 SAFETY & WARNING.....................................................................................................................
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 Introduction 98A This manual has been compiled to help you to operate your craft with safety and pleasure. It contains details of the craft, the equipment supplied or fitted, its systems, and information on its operation and maintenance. Please read it carefully, and familiarize yourself with the craft before using it.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 Manufacturer’s Recommendation The total number of persons, motor power and total weight shall not exceed the limits printed on the boat. Please refer to the boat's hull label for the actual values of your boat. See Table A.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 Description Challenger Series 2 1 3 4 98A 5 6 8 10 Challenger 3a 11 1 2 3 4 5 6 8 10 11 Challenger 4a Seahawk Series Seahawk 1 2 4 5 6 " " - Recommended seating arrangement of the occupants. 7 8 1 9 10 11 2 4 5 3 Seahawk 2 1 2 3 6 7 Seahawk 3 4 5 6 7 8 9 10 11 Seahawk 4 " " - Recommended seating arrangement of the occupants.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Excursion Series 1 2 3 4 5 6 7 9 10 11 1 2 3 4 Excursion 2 1 2 3 4 5 6 6 9 11 10 1 2 3 4 5 6 Excursion 4 7 3 2 Excursion 5 " - Recommended seating arrangement of the occupants. 4 5 7 10 12 8 11 " 9 10 9 Mariner 3 1 7 11 Excursion 3 7 " 5 6 13 9 " - Recommended seating arrangement of the occupants.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Mariner 4 1 2 3 4 5 10 7 12 8 11 6 " 1 2 3 4 5 6 7 13 9 " - Recommended seating arrangement of the occupants.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Inflating Instructions Before starting, locate a clean area free of stones or other sharp objects. Unroll the boat so it is laid out flat, and locate your pump. Use a hand or foot operated air pump to inflate the boat. Do not use high-pressure air compressors. Adults should inflate the chambers following the numerical sequence marked on the valves.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 Fishing Rod Holder Use (Certain Models): 1. Slide the end cap over the end of the fishing rod. 2. Insert the fishing pole into the holder. 98A Fishing Rod Seat Installation: Certain Models: 1. Inflate each seat cushion slowly to about 75% of its capacity. 2. Attach the seat cushion hinge to the hinge on the boat. Repeat the connection on the other side and for all seats. See Fig A. 3.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A FOR BOATS WITH ROTATION OAR-LOCK: Coupler Cover 10733 10734 Shaft A Pin Blade Shaft B Coupler Retainer Ring 1. 2. 3. 4. 5.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Grab Line Installation (Certain Models): IMPORTANT: To properly install the inflatable boat’s grab line and/or accessory lines, first inflate the boat. If is necessary, begin the grab line installation at the rear of the boat by threading it through the rope holders completely around the outside of the boat. Tie the two loose ends in a square knot at the rear end of the boat.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Rules to Observe During Navigation • • • • • • • • • • • • • • • • • • Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others. Always keep control of your boat. Respect local regulations and practices. Near the shore, navigate in the designated boating area. Remember that weather conditions can rapidly deteriorate. Always be sure that you can reach a shelter rapidly.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Disassembly and Storage First clean your boat thoroughly following the Care and Maintenance instructions. Open all air valves and deflate boat completely. Remove all the accessories from the boat; seats, fishing rod holders, oars, gear pouch and battery pouch. Fold the left and right chambers of the boat towards the middle of the floor. It is not necessary to remove the slats to fold the boat.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 05/21/2014 98A Limited Warranty Intex Inflatable Boat Your Intex Inflatable Boat has been manufactured using the highest quality materials and workmanship. All Intex Inflatable Boats have been inspected and found free of defects prior to leaving the factory. This Limited Warranty applies to the Intex Inflatable Boat only.
