Product Manual
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of
the inlet as follows:
1. Briey turn the “cutting system reverse” switch
(2) (g. 7) to position “R”. The cutting system and
the conveyor belt run in reverse. The material is
released and returned by the conveyor belt.
2. Redistribute the returned material, or remove
some of it from the conveyor belt (12).
3. After allowing the motor to cool down for
approximately 10 minutes (depending upon
ambient temperature), the machine can once
again be started in the forward direction and
shredding can be continued (rotary switch (2)
(g. 7) in position “1”).
MOTOR FAULT:
The machine is equipped with a thermally protec-
ted motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot lamp
„MOTOR FAULT“ (4) (g. 7) ashes.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the rotary switch (2) turned on?
- is the door (10) closed?
- is the collecting bag full?
The bag has to be emptied.
- is there a paper jam?
Follow the instructions under „AUTOMATIC
RESPONSE IN CASE OF OVER-LOADING“.
- is the motor overloaded?
Please refer to the section headed „MOTOR
FAULT“.
- Has one of the contactors failed?
See description under „ELECTRICAL MAL-
FUNCTION“.
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
other faults are statable, the machine
-
partment.
CUTTING SYSTEM
MAINTENANCE (6x50 mm):
After approximately 2 hours of con-
tinuous operation, spray some of the
included special oil onto an absorbant
sheet of paper and feeded to the cutting
system.
GEAR BOX MAINTAINANCE:
Both synchron gears, as well as the chain wheels
and drive chains must be greased monthly.
before the machine is opened.
Proceed as follows:
1. Remove the left-hand housing side panel and
the covering hood.
2. Grease the above mentioned parts with a brush
or a grease gun, and a standard, commercially
available grease.
3. Mount the side panel and the covering hood
and plug in the mains plug. The machine can
once again be placed into operation.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(main switch (1) (g. 7) switched to „0“).
ELECTRICAL MALFUNCTION:
If the control display (5) (g. 7) lights up and the
control display (4) (g. 7) blinks at the same time,
one of the integrated contactors is no longer
functional and the machine may no longer be
operated.
Switch the machine off at the mains switch (1)
(g. 7), pull the mains plug from the socket and
notify your dealer.
switch and lock it with a padlock before
repairs.
86434 12 08/16
14.95
9
MALFUNCTION
MAINTENANCE
ACCESSORIES
Description Order-No.
Plastic bag, 600 x 490 x 1500 x 0,06 mm 99969
Receptacle, 620 x 430 x 740 mm (optional) 75970
Lubrication bottle, 110 ml 88035
Angle guard set for extended table (optional) 86223
Note: Please contact your dealer when ordering accessories and replacement parts.
TECHNICAL DATA
Cutting width: 3.8x40 mm (cross-cut)
6x50 mm (cross-cut)
5.8 mm (strips)
11.8 mm (strips)
Cutting capacity (in two stacks):
3.8x40 mm: 100-110 sheets (70 g/m
2
)
85-95 sheets (80 g/m
2
)
6x50 mm: 130-140 sheets (70 g/m
2
)
110-120 sheets (80 g/m
2
)
5.8 mm: 130-140 sheets (70 g/m
2
)
110-120 sheets (80 g/m
2
)
11.8 mm: 180-190 sheets (70 g/m
2
)
155-165 sheets (80 g/m
2
)
Working width: 428 mm
Power input: 7 kW
Power output: 4 kW
Supply voltage: 400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz: 25 A
220V-230V/50Hz: 32 A
200V/50Hz: 35 A
Length: 1680 mm
Width: 1210 mm
Height: 1640 mm
Noise level: approx. 63 dB(A)
Weight: approx. 435 kg
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
DISPOSING
GB