Manual

7
005 S
GB
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
Disposing
Cutter and Adjustment
The cutter is user replaceable. The cutter will service
up to approximately 1000 discs.
Do not attempt to replace cutter while ma-
chine is in operation. Caution should be
used when removing and installing cutter.
Cutter teeth are sharp.
Remove Power
Turn power switch off prior to replacing cutter. Remo-
ving the unit from the power source is acceptable; the
memory control circuit contains a battery back-up and
will retain the destroyed disc count.
Remove Old Cutter
Step 1: Rotate pressure arm to the right as shown
above.
Step 2: Remove the old cutter by gently twisting the
plastic housing of the cutter @ 1/8 turn clo-
ckwise.
Step 3: Gently grasp the cutter housing and pull
straight up.
Insert New Cutter
Insert the new cutter by aligning the three plastic tabs
and metal keyed shaft of the cutter into the cutter
spindle receptacle. Gently press the cutter into positi-
on; press down and turn the plastic cutter housing @
1/8 turn counter-clockwise. While holding plastic tabs,
the cutter may need to be rotated to allow the shaft to
drop in place. Reposition pressure arm to the center
over cutter.
Adjustment
Minor adjustment of cutting depth is possible by ro-
tating the pressure adjustment ring either clockwise
(to relieve pressure on the disc cutting surface) or
counter-clockwise (to increase pressure on the disc
cutting surface).
To remove and clean, or remove and replace the
dust bag, open the back cover by pressing un-
der one of the Waste Collection Bin tabs while
lifting up—repeat on opposite side; remove the
bag and insert a new bag. The dust bags are de-
signed to hold the information bearing layers up
to 500 discs. If needed, additional replacement
bags may be purchased using the order form on
the back of this manual. Two dust bags were in-
cluded in the original packaging.
Cleaning the machine
Dust Bag Removal
To clean the unit, please remove the dust bag
periodically and dispose of the dust bag in a
trash receptacle.
You can use a small vacuum cleaner to perio-
dically vacuum any dust particles that have ac-
cumulated on the top surfaces of the unit. You
may also use a moist cleaning towel to wipe the
unit down. Please do not use chemical cleaning
agents to clean the unit as the nish of the pla-
stic parts may discolor.
Trouble Shooting-Technical Support
Error Code: E20
Carefully vacuum out particle debris. Remove
the particle debris with a vacuum; thoroughly
clean around the Disc Retaining Spindle. Reset
the LED indicator by depressing the red Stop
button. If the problem persists call technical sup-
port to resolve the issue.
Error Code: 500
This shows that 500 discs have been destroyed.
Digital “500” will ash. This is a reminder to cle-
an the unit and check both dust bag and cutter,
replacing as necessary. To reset the LED indica-
tor power the unit off, depress and hold the blue
Start button, power the unit on while continuing
to hold the blue Start button for two seconds or
until a long beep is heard, then release the blue
Start button.
After the Error Code: 500 is displayed and the
unit is reset the LED will display the total discs
destroyed. The example to the left represents
10,230 discs destroyed. The LED will rst dis-
play 10 then 230. Turn power switch off and back
on exit this mode and the counter to 000.
Error Code: E00
The unit incorporates a safety feature to prevent
the cutter from operating with the cover open.
E00 shows that the cover has been opened whi-
le power is applied to the unit. Simply shut the
cover completely and the error will reset.
Recycle for a Greener Earth
Unit is designed to grind the data layer of a CD-
ROM, CD-R, or CD-RW disc thus making the
information totally unreadable. The resulting
process produces a clear polycarbonate disc;
the residual ink and metals are collected in the
dust bag.
Both the dust bag and the polycarbonate disc
can be discarded in a normal trash container.
However, an alternative recycling program is
offered, which takes all discarded materials and
recycles them for a cleaner environment.
Example of Properly
Processed CD-R Disc
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
90019 4 11/13